Necto Group 2AMDI511IPVRDS Manuel utilisateur

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

USER MANUAL 2AMDI511IPVRDS

SUBJECT INDEX:

DESCRIPTION

TECHNICAL SPECIFICATION

DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE

OPERATION MODES

LINEAR POTENTIOMETER MODE 100KOHM

MODE 0-10V/1-10V PASSIVE

PUSH MODE

DALI MODE

PARAMETERS CONFIGURATION

pag|1

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

CONTROL INPUTS

DALI

0-10V;1-10V PUSH NO

(INSULATED) LINEAR POTENTIOMETER

X1 X1

MAX OUTPUT CURRENT*

da 170mA a 1050mA

TECHNICAL NOTES

- Mono channel Dimmers with Output Current PWM.

- Input Range: 8-53V DC.

- Output Current PWM with current from 170mA a 1050mA

(54.6W at 52V DC).

- Input Controls: Insulated Push button x1, DALI x1,

Linear Potentiometer 100K x1, 0-10V Passive x1,

1-10V Passive x1.

- Printed Circuit UL.

- Protection Class: IP20.

- Standard Dimension 40x80x24.45 mm.

- Dimension with accessories 40x100x24.45 mm.

- Reverse polarity protection.

- Open circuit protection.

- Surge voltage protection.

- Over temperature protection.

- Short circuit protection.

PULSANTE N/O ISOLATO

DIMMER MONOCANALE MULTIPROTOCOLLO COSTANT CURRENT

2AMDI511IPVRDS

NO isulated switch

Mono channel Dimmers with Output Current PWM. Input Range: 8-53V DC.

Output Current PWM with current from 170mA a 1050mA (54.6W at 52V

DC). In order to set the output current you will need the 2AMIN4030000N

interface sold separately. Default current 350mA. In order to set the fade

output and the logarithmic or linear output you will need the 2AMIN4030000N

interface sold separately, the other working modes are automatically

detected by the device. Please refer to user manual.

pag|2

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

CODE INPUT

VOLTAGE

(MAX) OUTPUT

CURRENT

n. OUTPUT

CHANNELS

MAX OUTPUT

POWER CONTROL INPUTS CASE DIM.

2AMDI511IPVRDS 8-53V DC DA 170mA

A 1050mA 154.6W A 52V DC

INSULATED PUSH BUTTON X1

DALI X1

LINEAR POTENTIOMETER

100K X1

0-10V PASSIVE X1

1-10V PASSIVE X1

YES 40X80 mm

h 24,45 mm

pag|3

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

POWER SUPPLY CONNECTION DIAGRAM AND LED 2AMDI511IPVRDS - FIGURE N. 1

The 2AMDI511IPVRDS dimmer has to be powered according to the polarity showed in FIG. 1

through the DC IN (+ and -) terminals.

In case the power supply polarity is inverted no damage will be caused to the device .

The LED (LED PWR) positioned on the circuit board indicates the presence of power supply.

The LED (LED DIM) shows the dimming level of the output.

The LED load connection has to be made by using the OUT (L+ and L-) terminals.

DEVICE POWER SUPPLY AND CONNECTION

TO THE LED MODULE

pag|4

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

POTENTIOMETER WIRING 2AMDI511IPVRDS - FIGURE N. 2

In order to activate this mode of control/operation just connect a linear potentiometer of 100 Kohm between the D+

and D- inputs and disconnect the remaining inputs.

By default, the dimming curve follows a logarithmic trend proportional to the resistance value set by the

potentiometer.

A resistance value of less than 5 Kohm is interpreted as load off.

The maximum brightness value is reached by exceeding the value of 95 Kohm.

In case the potentiometer is disconnected, the dimmer sets the output to the saved level (see preset level

change).

The preset value is zero by default.

On the rst run in this mode it could be necessary to set the input to a value greater than 50% (55K or higher on DD

+ input) in order to congure the dimmer to the potentiometer mode.

*This setting can be congured through the interface cod. 2AMIN4030000N

OPERATION MODES

LINEAR POTENTIOMETER MODE 100KOHM

pag|5

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

WIRING 0-10V 2AMDI511IPVRDS - FIGURE N. 3

In order to activate this mode of control/operation just connect the active control signal of 0-10V/1-10V between

the D+ and D- inputs (being careful to observe the correct polarity) and disconnect the remaining control signals.

The maximum current absorbed by 0-10V dimmer interface is 0,1 mA.

By default, the dimming curve follows a logarithmic trend proportional to the control voltage. A voltage value of less

than 1V is interpreted as load off.

In case the 0-10V/1-10V signal is disconnected, the dimmer sets the output to the saved level (see preset level

change). The preset value is zero by default.

On the rst run in this mode it could be necessary to set the input to a value greater than 50% (5V or higher on DD

+ input) in order to congure the dimmer to the 0-10V/1-10V mode.

*This setting can be congured through the interface cod. 2AMIN4030000N

MODE 0-10V/1-10V PASSIVE

pag|6

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

WIRING BUTTON 2AMDI511IPVRDS - FIGURE N. 4

In order to activate this mode of control/operation it is necessary to remove any control signals from the D + and Dinputs

and connect between the DALI/P1 and DALI/P2 inputs, a signal in direct or alternating voltage

(DC voltage range:10÷265V, AC 12÷265Vac 50÷65Hz) interrupted by a normally open button (N.O.).

No polarization is needed for the input signal.

The maximum current absorbed by the PUSH interface is about 2mA.

The dimmer saves the output position in order to restore the set level in case of power failure (preset).

PUSH interface operation

Single Click (rapid press (<1sec))

- Turns on or off the output (ON/OFF).

Double Click (rapid press (<1sec))

- Sets maximum brightness (output= 100%)

Long Press (long press (>1sec))

- If the dimmer is in OFF position, it sets the output to the minimum value (default= 1%)

- If the dimmer is in ON position, the long press enables the output dimming (up/down).

PUSH MODE

pag|7

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

DALI 2AMDI511IPVRDS WIRING - FIGURE N. 5

In order to activate this mode of control/operation it is necessary to shortcircuit the D+ and D- inputs and connect

the DALI bus between the DALI/P1 and DALI/P2 inputs.

On the rst reception of a properly formatted DALI package the dimmer is congured in DALI mode. Once

congured in DALI mode and disconnected from the DALI bus the dimmer switches to the POWER ON LEVEL

mode set through DALI bus.

The maximum current absorbed by the DALI bus is about 2mA.

Below you can nd the implemented standard commands:

DIRECT ARC POWER

OFF

DOWN

STEP UP

STEP DOWN

RECALL MAX LEVEL

RECALL MIN LEVEL

STEP DOWN AND OFF

ON AND STEP UP

GO TO SCENE (0-15)

RESET

STORE ACTUAL LEVEL IN THE DTR

STORE THE DTR AS MAX LEVEL

STORE THE DTR AS MIN LEVEL

STORE THE DTR AS SYSTEM FAILURE LEVEL

STORE THE DTR AS POWER ON LEVEL

STORE THE DTR AS FADE TIME

STORE THE DTR AS FADE RATE

STORE THE DTR AS SCENE (0-15)

REMOVE FROM SCENE (0-15)

ADD TO GROUP (0-15)

REMOVE FROM GROUP (0-15)

STORE DTR AS SHORT ADDRESS

DALI MODE

pag|8

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

QUERY STATUS

QUERY BALLAST

QUERY LAMP POWER ON

QUERY LIMIT ERROR

QUERY RESET STATE

QUERY MISSING SHORT ADDRESS

QUERY VERSION NUMBER

QUERY DEVICE TYPE

QUERY PHISICAL MINIMUM LEVEL

QUERY POWER FAILURE

QUERY CONTENT DTR1

QUERY CONTENT DTR2

QUERY ACTUAL LEVEL

QUERY MAX LEVEL

QUERY MIN LEVEL

QUERY POWER ON LEVEL

QUERY SYSTEM FAILURE LEVEL

QUERY FADE TIME/FADE RATE

QUERY SCENE LEVEL (0-15)

QUERY GROUPS (0-7)

QUERY GROUPS (8-15)

QUERY RANDOM ADDRESS H

QUERY RANDOM ADDRESS M

QUERY RANDOM ADDRESS L

pag|9

USER MANUAL 2AMDI511IPVRDS

www.nectogroup.com

PARAMETERS CONFIGURATION

CLICK ON THE WANTED CONFIGURATION TO VIEW 2AMIN4030000N

PROGRAMMER IMAGE

Reset