NEC NECCare Platinum Express5800/A1160 Manuel utilisateur

EXPRESS5800/A1160



Service Processor

Troubleshooting Guide 

Proprietary Notice and Liability Disclaimer

The information disclosed in this document, including all designs and related materials, is the

valuable property of NEC Corporation of America, Inc. and/or its licensors. NEC Corporation

of America and/or its licensors, as appropriate, reserve all patent, copyright and other

proprietary rights to this document, including all design, manufacturing, reproduction, use,

and sales rights thereto, except to the extent said rights are expressly granted to others.

The NEC Corporation of America product(s) discussed in this document are warranted in

accordance with the terms of the Warranty Statement accompanying each product. However,

actual performance of each product is dependent upon factors such as system configuration,

customer data, and operator control. Since implementation by customers of each product

may vary, the suitability of specific product configurations and applications must be

determined by the customer and is not warranted by NEC Corporation of America.

To allow for design and specification improvements, the information in this document is

subject to change at any time, without notice. Reproduction of this document or portions

thereof without prior written approval of NEC Corporation of America is prohibited.

Trademarks

Windows is a registered trademark of Microsoft Corporation.

Intel and Itanium are registered trademarks of Intel Corporation.

All other product, brand, or trade names used in this publication are the trademarks or

registered trademarks of their respective trademark owners.

PN: 456-01807-000 December, 2008

NEC Corporation of America

10850 Gold Center Drive, Suite 200,

Rancho Cordova, CA 95670

iii

Contents

Section 1 Introduction ....................................................................1-1

1.1. Documentation Updates..................................................................... 1-1

1.2. Preparing to Restore the Service Processor...................................... 1-1

1.2.1. Identifying the Boot Cell..................................................................... 1-1

1.2.2. Recording Partition Configuration...................................................... 1-3

1.2.3. Workstation Requirements................................................................. 1-3

1.3. Accessing the Service Processor....................................................... 1-3

1.3.1. Logging On to Partition Remote Console Interface............................ 1-3

1.3.2. Accessing EXPRESSSCOPE® Monitor Interface.............................. 1-4

Section 2 Upgrading the Service Processor.................................2-1

2.1. Checking Management Firmware Level using Remote console

interface ............................................................................................. 2-1

2.2. Obtaining Releases from the Support Site......................................... 2-3

2.3. Updating Management Firmware using Remote console interface ...2-3

Section 3 Troubleshooting the Service Processor ......................3-1

3.1. Possible Problem Symptoms for the Service Processor.................... 3-1

3.2. Loss of Communication With Partition Remote console interface ..... 3-1

3.2.1. Pinging the Service Processor........................................................... 3-1

3.2.2. Verifying Network Access to Your System.......................................... 3-2

3.2.3. Verifying Partition Network Settings................................................... 3-3

3.2.4. Rebooting the Service Processor....................................................... 3-4

3.2.5. Restoring the Service Processor to Default Settings......................... 3-4

3.3. Cell Is Not Responding ...................................................................... 3-5

3.3.1. Rebooting the Service Processor....................................................... 3-5

3.3.2. Checking Cell Interconnect Cable Connections.................................3-6

3.3.3. Restoring the Service Processor to Default Settings......................... 3-6

3.4. Error Messages Displayed on EXPRESSSCOPE® Monitor LCD...... 3-6

3.4.1. Message: “ID Indeterminate”.............................................................. 3-7

3.4.2. Message: “ID Conflict”........................................................................ 3-7

Contents

3.4.3. Message: “Segment Conflict”............................................................. 3-8

3.4.4. Message: “Segment Down” ............................................................... 3-9

3.4.5. Message: “Switch Error” .................................................................. 3-10

Section 4 Restoring the Service Processor .................................4-1

4.1. Before Restoring to Default Settings.................................................. 4-1

4.2. Restoring Service Processor to Default Settings............................... 4-1

4.2.1. Default Settings.................................................................................. 4-1

4.2.2. Restoring the Default Settings........................................................... 4-3

4.2.3. Configuring After Restoring................................................................ 4-3

Section 5 Configuring the Service Processor After Restoring...5-4

5.1. Configuring After Updating Management Firmware........................... 5-4

5.2. Configuring After Restoring Default Settings ..................................... 5-4

5.2.1. Reconfiguring Service Processor on a Non-boot Cell........................ 5-4

5.2.2. Reconfiguring Service Processor on a Boot Cell............................... 5-5

5.2.3. Reconfiguring Service Processor on a Boot Cell in a Multiple Cell

Partition.............................................................................................. 5-5

5.3. Configuration Procedures.................................................................. 5-6

5.3.1. Configuring Network Settings ............................................................ 5-6

5.3.2. Resolving Partitioning Inconsistencies............................................. 5-10

5.3.3. Creating Partitions ........................................................................... 5-10

5.3.4. Moving Cells to Other Partitions .......................................................5-11

5.3.5. Specifying Partition Settings ............................................................ 5-12

5.3.6. Adding User Credentials using Remote console interface............... 5-13

5.3.7. Eliminating Browser Startup Warnings using Remote console

interface........................................................................................... 5-14

5.3.8. Configuring Alerts and the SMTP Server using Remote console

interface........................................................................................... 5-15

Appendix A Related Documents and Web Resources ........ A-1

A.1 Express5800/A1160 Documentation Library......................................A-1

A.2 Web Resources .................................................................................A-2

Figures

Figure 1-1 EXPRESSSCOPE® Monitor LCD Main Screen Layout..............................1-2

Figure 1-2 Partition Setting Page..................................................................................1-2

Figure 2-1 Management Firmware Update Page..........................................................2-2

Figure 2-2 Management Firmware Revision Status......................................................2-2

Figure 2-3 Management Firmware Updates Page........................................................2-3

Figure 2-4 Management Firmware Revision Status......................................................2-4

Figure 3-1 Location of Maintenance LAN Port..............................................................3-2

Figure 3-2 Location of Boot Cell Indicator on Main Screen of EXPRESSSCOPE®

Monitor Interface....................................................................................................3-3

Figure 3-3 Location of Management Board Reset Button.............................................3-4

Figure 3-4 Location of Management Board Reset Button.............................................3-5

Figure 3-5 Location of Management Board Reset Button...........................................3-10

Figure 5-1 Settings Reserved.......................................................................................5-7

Figure 5-2 Expanded Network Menu............................................................................5-8

Figure 5-3 Setting IPAddress Value.............................................................................5-9

Figure 5-4 Applying IP Address Changes.....................................................................5-9

Figure 5-5 Partitioning Page.......................................................................................5-10

Figure 5-6 User Management Page............................................................................5-13

Figure 5-7 User Management Add New User Page....................................................5-14

Figure 5-8 SMTP Page...............................................................................................5-16

Figure 5-9 Alert Management Page............................................................................5-17

Figure 5-10 Alert Management - Modify Email............................................................5-18

Figure 5-11 Alert Management - Modify SNMP Trap ..................................................5-19

Using This Guide

This guide provides the information necessary for upgrading firmware on your Service

Processor or troubleshooting software problems with your Service Processor.

Who Should Use This Guide

This guide is intended for system administrators and facilities personnel who are

responsible for installing and administering Express5800/A1160 server.

Symbols and Conventions

This guide uses the following text conventions and graphic symbols.

Warnings, cautions, and notes have the following meanings:

WARNING

Warnings alert you to situations that could result in serious personal injury or loss

of life.

CAUTION

Cautions indicate situations that can damage the system hardware or software.

Note: Notes give important information about the material being described.

Names of keyboard keys are printed as they appear on the keyboard. For example,

Ctrl, Alt, or Enter.

Text or keystrokes that you enter appear as boldface type. For example, type

abc123 and press ENTER.

File names are printed in uppercase letters. For example, AUTOEXEC.BAT.

Related Documents

In addition to this guide, the following system documentation is useful.

NECCare™ Guide

The NECCare Guide contains information about NEC’s warranty and server registration.

Safety Notices

vii

Safety Notices

WARNING

To avoid a risk of injuries, maintenance procedures require trained technical

personnel.

In maintenance procedures with voltages of 42.4V peak or 60Vdc or more, take

safety measures, such as wearing insulated rubber gloves. Performing work

without these measures may cause electric shock.

In an emergency, such as a dangerous event that requires turning off the power

supply, turn off the breaker at the rear of the server. Turning off the breaker may

cause data destruction. Therefore, users should determine when to turn off the

breaker in accordance with specified operation criteria.

The server is equipped with a front stabilizer. Engage the front stabilizer during

installation. For stability and to distribute the weight, also attach side stabilizers.

Otherwise, the rack may topple over and cause injuries.

If you extend two or more devices from the rack at the same time, the rack may

topple over on you. Extend only one device from the rack at a time.

Exercise great care not to hurt your fingers on the rail when you mount/dismount

the equipment into/from the rack.

Lithium batteries can be dangerous. Improper handling of lithium batteries may

result in an explosion. Dispose of lithium batteries as required by local ordinance.

Replace only with the same or equivalent type battery.

A liquid crystal display is used in this server. When handling a damaged liquid

crystal display, take care to avoid exposure to the liquid inside the liquid crystal

display. The liquid can cause bodily harm. In the event the liquid is ingested,

gargle at once and consult a doctor immediately. If the liquid comes in contact

with skin or gets into the eyes, wash the skin with cool running water, or flush the

eye with cool running water for at least 15 minutes and consult a doctor.

The DVD-ROM drive uses a laser beam. Do not look or insert a mirror inside

while the system is on. A laser beam is invisible; if your eyes get exposed to it,

there is a risk of losing your eyesight.

Elevated Operating Ambient Temperature – If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may be greater

than the room ambient environment. Therefore, consideration should be given to

Safety Notices

viii

installing the equipment in an environment compatible with the maximum rated ambient

temperature of 89.6°F.

Reduced air Flow – Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not compromised.

To prevent fires, and damage to rack equipment and supply wiring, make sure that the

rated load of the power branch circuit is not exceeded. Equipment nameplate ratings

should be used when addressing this concern. For more information on installation and

wiring of power-related facilities, contact your electrician or local power company.

To prevent electrical shock, connect all rack and rack support equipment to the same

electrical circuit of the building wiring. If you are unsure, check the building wiring to

avoid remote earth conditions.

For safe operation, only connect the equipment to a building supply that is in accordance

with current wiring regulations in your country. In the USA those wiring standards are

regulated by Underwriter Laboratories (UL); in the U.K. by the Institution of Electrical

Engineers, (IEE) and in Canada by the Canadian Standards Association (CSA).

WARNING

Some locations within the server have high voltage and therefore are very

dangerous. To avoid risk of electric shock, turn off all server power and

disconnect power cables before working inside the server unit.

The main power of your server is turned off by turning off the power source to the

server or removing the power cable.

Before touching the parts in the server, wait for at least 10 to 15 seconds until

residual voltage is discharged.

Online maintenance – During and after servicing, do not leave the server door open

unless necessary to perform servicing.

WARNING

Take care not to short live components with conductive tools, such as an

adjustable wrench.

To prevent shock, take care not to drop or leave conductive parts, such as a

screw, in the server when servicing the system.

Be careful when accessing a fan or rotating parts to avoid cutting your hand or

fingers.

Safety inspections – When servicing the system, check equipment that can cause harm

due to deterioration, and if necessary, replace the part.

Safety Notices for Users Outside of the U.S.A. and Canada

PELV (Protected Extra-Low Voltage) Integrity: To ensure the extra-low voltage integrity

of the equipment, connect only equipment with mains-protected electrically-compatible

circuits to the external ports.

Remote Earths: To prevent electrical shock, connect all local (individual office)

computers and computer support equipment to the same electrical circuit of the building

wiring. If you are unsure, check the building wiring to avoid remote earth conditions.

Earth Bonding: For safe operation, only connect the equipment to a building supply that

is in accordance with current wiring regulations in your country. In the USA those wiring

standards are regulated by Underwriter Laboratories (UL); in the U.K., by the Institution

of Electrical Engineers, (IEE) and in Canada by the Canadian Standards Association

(CSA).

Autres manuels pour NECCare Platinum Express5800/A1160

Table des matières

Autres manuels NEC Serveur

NEC

NEC Express5800/R310e-E4 Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC NEC Express5800/R120d-2E Manuel utilisateur

NEC

NEC A1160 Guide d'installation

NEC

NEC NECCare Gold Express5800/320Fd Manuel utilisateur

NEC

NEC Express5800/140Rf-4 Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel d'utilisation

NEC

NEC Express5800/R110f-1E Manuel utilisateur

NEC

NEC SX-Aurora TSUBASA A300-4 Manuel utilisateur

NEC

NEC Express 5800 Manuel utilisateur

NEC

NEC N8100-1575F Manuel utilisateur

NEC

NEC Univerge SV8100 Manuel utilisateur

NEC

NEC Express 320Lc Manuel utilisateur

NEC

NEC Express5800/T120e Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel d'utilisation

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC Express5800 110Ej Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

NEC

NEC EXP805 Manuel utilisateur

NEC

NEC Univerge SV8100 R2 Guide d'installation

NEC

NEC N8146-43 Manuel utilisateur

NEC

NEC NEC Express5800 Series Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur