NEC SuperScript 1800 Manuel utilisateur

A Phillips-head screwdriver is required for installing the NEC SuperScript 1800 PostScript

Level 2 Upgrade Kit.

Accessing the Printer Controller Board

Installing the PostScript Level 2 SIMM

This upgrade kit comes with one PostScript

Level 2 compatibility SIMM.

This product is not manufactured or distributed by Adobe Systems, Inc., the owners of the registered trademark PostScript

1. Turn off the printer.

Pull-out 500-sheet Cassette

(A)

3. Disconnect all cables from printer.

4. Position the printer so right-side can be accessed.

5. Remove screws from side-panel then open back-

panel

(B)

6. Pull tab to release side-panel

(C)

7. Slide side-panel towards back

(D)

8. Rotate side-panel away from printer (assure wire-snaps

on the parallel port are not in way), then lift away

(E)

9. Loosen top screw of controller board cover, remove

remaining 4 screws, then remove cover

(F)

1. Position the printer so you have access to the

controller board.

Figure

(A)

shows the controller board and the

location of the PostScript SIMM slot. The PostScript

SIMM must be installed into the ﬁrst slot.

3. Locate notch on the SIMM

(B)

4. Position the SIMM into the slot so that the notch is at

the bottom

(C)

5. Snap the SIMM into position

(D)

6. Use previous procedure as guide to replace printer side-

panel, 500-sheet Cassette, and printer cables.

7. For computers running Microsoft Windows, install a

PostScript printer driver as described by Chapter 3,

“Installing the Software,” of the SuperScript 1800 User’s

Guide. For Macintosh computers, use the Mac OS Help

system for choosing a PostScript printer.

ABC

DEF

Install the PostScript SIMM into the ﬁrst slot.

Notch

NEC

ART

. 808-878303-011A

UPER

CRIPT

1800

OST

CRIPT®

EVEL

2 C

OMPATIBILITY

PGRADE

NSTRUCTIONS

Use this instruction sheet for installing the optional NEC SuperScript 1800 500-sheet 2nd Cassette (Tray 3). The cassette can

hold 500 sheets of medium weight paper or 40 envelopes. Do not load transparencies or label sheets in the 500-sheet 2nd

Cassette. For a complete list of usable media sizes see Appendix B, in the

SuperScript 1800 User’s Guide

Installing the 500-sheet 2nd Cassette

Loading Paper in the 500-sheet 2nd Cassette

1. Turn off the printer.

2. Remove all cables

(A)

3. Make sure there is plenty of room around and

above the printer to work. Remove the 500-sheet

2nd Cassette from its packaging.

4. Put the 500-sheet 2nd Cassette unit next to the

printer.

5. Carefully place the printer on the 500-sheet 2nd

Cassette unit as shown

(B)

6. Reconnect all cables.

7. Turn on the printer

(C)

8. Make sure READY appears on the Operator Panel display.

9. If you are using the Windows PostScript printer driver,

open the Properties window, view the Device Options

(Windows 95/98) or Device Settings (Windows NT 4.),

and make sure that the optional cassette (Tray 3) is

selected.

10. Conﬁrm the installation by printing a printer

conﬁguration page from the Operator Panel as described

in Chapter 5 of the

SuperScript 1800 User’s Guide

1. Remove the tray from the 2nd Cassette unit

(A)

Take out the styrofoam packing.

2. Make sure the lever on the left-front side of the

cassette tray is positioned into the hole at the end of

the slot

(B)

3. Squeeze and adjust the Back Paper Guide to the

desired paper length

(C)

4. Make sure the Envelope Guide is adjusted to its back

position

(D)

5. Lift the tab on the top of Side Guide 1 and slide it to the

paper size indicated on the tray bottom

(E)

6. Place the paper into the tray

print side down

7. Move Side Guide 2 to ﬁt lightly against the paper

stack

(F)

8. Reinsert the tray into the 500-sheet 2nd Cassette unit.

To load envelopes please see the User’s Guide.

ABC

note: The 500-sheet 2nd Cassette is

referred to asTray 3 in the printer driver and

on the Operator Panel.

Envelope Guide

lever

NEC

UPER

CRIPT

1800

PTIONAL

500-

SHEET

ASSETTE

— I

NSTRUCTIONS

ART

. 808-878305-011A

A Phillips-head screwdriver is required for installing the NEC SuperScript 1800 IrDA and Serial Interface Upgrade Kit.

Accessing the Printer Controller Board

Installing the IrDA Interface Card and Adapter

1. Turn off the printer.

Pull-out 500-sheet Cassette

(A)

3. Disconnect all cables from printer.

4. Position the printer so right-side can be accessed.

5. Remove screws from side-panel then open back-

panel

(B)

6. Pull tab to release side-panel

(C)

7. Slide side-panel towards back

(D)

8. Rotate side-panel away from printer (assure wire-snaps

on the parallel port are not in way), then lift away

(E)

9. Loosen top screw of metal controller board cover, remove

remaining 4 screws, then remove cover

(F)

1. Position the printer so you have access to the back.

Remove screw from the metal back plate

(A)

3. Insert IrDA Interface Card into printer

(B)

4. Connect card with socket on controller board

(C)

5. Use screw, removed in Step 2, to fasten the card

(D)

6. Use previous procedure as guide to replace printer

side-panel, 500-sheet Cassette, and printer cables.

7. If only using the serial connection, go to Step 10.

8. Connect IrDA adapter to IrDA port

(E)

9. Aim adapter at your computer’s IrDA sensor. Do not

allow more than 3 feet of separation

(F)

10. For more information about installing the IrDA driver

or using the serial port, see Chapter 8 of the SuperScript

1800 User’s Guide.

ABC

DEF

E3 feet or less

Connect to

socket on

controller

board

NEC S

UPER

CRIPT

1800

AND

ERIAL

NTERFACE

PGRADE

— I

NSTRUCTIONS

ART

. 808-878300-011A

Tools Required

Accessing the Printer Controller Board

Turn off the printer.

Pull-out the Tray 2 (A).

Disconnect all cables from printer.

Position the printer so the right-side can be accessed.

Remove screws from side-panel, then open back panel (B).

Rotate side-panel away from the printer (assure wire-

snaps on the parallel port are not in the way), then lift

away (E).

Loosen top screw of controller board cover, remove

remaining four screws, then remove cover by lifting up

then towards you.(F).

ABEF

Cut Here

Second Fold Here Second Fold Here

Accessing the Printer Controller Board (continued)

Gently pull tab to release side-panel (C).

Slide side-panel towards back (D).

Phillips-head Screwdriver

Introduction

Installation involves accessing the Printer Controller Board

then installing the interface card.

SuperScript 1800

Instructions for the

Apple LocalTalk and Serial Interface Upgrade Kit

Cut Here

Second Fold Here

Cut Here

Connect card with socket on Controller Board (C).

Use screw, removed in Step 2, to fasten card (D).

13.

14. Connect the other end of the LocalTalk cable to your

Macintosh Computer.

Install the NEC SuperScript 1800 PPD onto your

Macintosh computer as described in Chapter 3,

"Installing the Software," of the SuperScript 1800 User’s

Guide.

See Chapter 8, "Printer Options," for information about

using the serial port.

18.

19.

20.

Installing the LocalTalk and Serial Interface Card

Position the printer so you have access to the back.

Remove screw from the metal back plate (A).

Insert Interface Card into the printer (B).

10.

11.

12.

Part No. 808-878301-011A

Connect

with socket

Installing the LocalTalk and Serial Interface Card (cont)

Second Fold Here

Use previous procedure (Step 1 to Step 9, "Accessing

the Printer Controller Board") as a guide to replace

printer side-panel, Tray 2, and printer cables.

If only using the serial connection, go to Step 11.

Connect Apple LocalTalk cable to interface card (E).

15.

16.

17.

Autres manuels pour SuperScript 1800

Table des matières

Autres manuels NEC Accessoires pour imprimantes

NEC

NEC SUPERSCRIPT 4400 SERIES Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel