NEC MultiSync UN462A Manuel d'utilisation et d'entretien
Firmware Update Procedure
by HTTP Server
Rev.0.1
2
Read This Manual before Attempting Firmware Update
This manual describes the procedure for updating firmware of monitor by using the HTTP server function.
For details on the HTTP server function, the names of the components of the monitor, the Display Menu
screen operations, and so on, refer to the instruction manual.
Precautions
Target models:
UN462A/UN462VA/UN492S/UN492VS/UN552A/UN552S/UN552VS/UN552/UN552V/UX552S/
UX552
Series name is A50UN. This name is displayed in "SERIES".
Do not turn off the main power to the monitor or remove the LAN cable during firmware update.
For details on making a connection to the monitor from a computer through a network, using the
HTTP server function of the monitor, read "LAN Control" in the instruction manual.
As your Web browser, you must use "Microsoft Internet Explorer 10.0" or later.
Since the monitor uses "JavaScript" and "Cookies", change your browser settings to enable the use
of these functions. The way in which these settings are made depends on the version of the browser.
So, refer to the browser Help and so on.
Updating the firmware does not affect any data set in the screen menu of monitor.
To apply a firmware version update over the network, DISPLAY and MEDIA PLAYER of
NETWORK FUNCTIONS must be enabled.
Symbols
This manual uses the following symbols.
Note
Describes information that must be noted.
Tip
Provides supplementary explanations and useful information.
3
Preparations to Be Completed Prior to Firmware Update
1. Connect a LAN cable to the monitor.
4
Updating Firmware
1. Start the Web browser on the computer to access the home screen
of the monitor.
The URL of the home screen of the monitor is "http://<IP address of the monitor>/pd_index.html".
2. Click "UPDATE FIRMWARE" on the menu on the left side of the
screen.
The GO TO UPDATE FIRMWARE screen appears.
5
3. Check the IP ADDRESS of MediaPlayer.
Tip
If you want to update the firmware by daisy chain, refer to "Daisy chain Firmware Update" (→
P13).
4. Click the [GO TO UPDATE FIRMWARE] button.
6
5. Click the [OK] button.
The UPDATE FIRMWARE screen appears.
6. Click the [Browse] button under "SELECT IMAGE".
7
7. Select the firmware image file to be updated and then click the
[Open] button.
Tip
The following table lists the initial file names of the firmware image files.
Firmware File name(Note) Extension
FIRMWARE NDS_CDT_A5 _UN_R****.pac .pac
（Note）R**** ：Revision Number
The names of the firmware image files can be changed (the name can consist of up to 1024
characters, including the extension).
Do not change the extension of a firmware image file.
If you want to update the firmware by daisy chain, refer to "Daisy chain Firmware Update" (→
P13).
8
8. Click the [UPDATE] button.
The dialog for confirming the start of update appears.
Firmware update starts. A message appears on the screen of the monitor and the LED (⑩in the
figure below) blinks in green. Upon the completion of update, the blinking pattern of the LED
changes. Go to "9. Confirm the LED blinking pattern of the monitor." (→P9).
Note
DonotturnoffthemainpowertothemonitororremovetheLANcableduringfirmware
update.
9
Tip
Time required ofupdateis 10minutes.
During update, " Updating...**%." is displayed on the screen.
9. Confirm the LED blinking pattern of the monitor.
Upon the completion of update, the LED blinking pattern changes.
Refer to "Confirming the Firmware Update Results" (→P10).
10.Turn the main power to the monitor off and then on again.
Note
To terminate firmware update, this procedure must be performed.
Otherwise, the monitor may fail to run normally
10
Confirming the Firmware Update Results
Upon the completion of update, the green-blinking LED changes to one of the following.
Alternately blinking in green and red (update successful).
Blinking in red (update failure).
When the LED is blinking in green and red alternately (update successful):
Update has completed normally.
Tip
When update has been successful, the screen of the monitor displays the following.
Autres manuels pour MultiSync UN462A
1
Ce manuel convient aux modèles suivants
10
Table des matières
Autres manuels NEC Moniteur
NEC
NEC LCD1810 - MultiSync - 18.1" LCD Monitor Mode d’emploi
NEC
NEC LCD1960NX - MultiSync - 19" LCD Monitor Manuel utilisateur
NEC
NEC MultiSync MD21GS-2MP Manuel du produit
NEC
NEC MultiSync LCD2180UX Manuel utilisateur
NEC
NEC LCD2070NX - MultiSync - 20" LCD Monitor Manuel utilisateur
NEC
NEC LCD19WMGX - AccuSync - 19" LCD Monitor Manuel utilisateur
NEC
NEC MultiSync EA271F Manuel utilisateur
NEC
NEC MultiSync X431BT Manuel utilisateur
NEC
NEC MultiSync ME Series Manuel utilisateur
NEC
NEC MultiSync V463 Manuel utilisateur
NEC
NEC MultiSync FE700+ Manuel utilisateur
NEC
NEC MultiSync X554UNS Manuel utilisateur
NEC
NEC MultiSync C551 Manuel utilisateur
NEC
NEC MultiSync V552 Manuel utilisateur
NEC
NEC ESERIES Manuel utilisateur
NEC
NEC V461-2 Manuel utilisateur
NEC
NEC SpectraView 2690 Manuel utilisateur
NEC
NEC MultiSync LCD2690WUXi Manuel utilisateur
NEC
NEC MultiSync V754Q Manuel utilisateur
NEC
NEC MultiSync V521 Manuel utilisateur
