NEC Versa AX Instructions d'installation
Versa AX Disassembly
nRequired Tools
nDisassembly Instructions
nReassembly Instructions
Disassembly and Reassembly - 2
Required Tools
All Versa AX maintenance procedures can be performed using the following tools:
nTweezers
nSmall flat-head screwdriver
nSmall Philips screwdriver
nRight-angled dentist style probe
Disassembly Instructions
This document contains step-by-step disassembly instructions for the Versa AX. The instructions are
clarified by images of the part that is being removed or disassembled. Furthermore, the screws that are
removed are shown next to the image of the parts themselves.
When disassembling the system unit, follow these general rules.
nDo not disassemble the system into parts that are smaller than those specified in
the instructions.
nLabel all removed connectors. Note where the connector goes and in what
position it was installed.
nTurn off the power and disconnect all power and all options. Also remove any
PC-Cards that are in the PCMCIA slot.
Disassembly and Reassembly - 3
1. Battery
Remove the battery pack of the notebook as follows:
a. Slide the latch into the unlock position as shown below and hold
it.
b. Slide the battery out of the bottom base.
Fig. 1: Battery and modem cap removal.
2. Modem
The following steps describe how to remove the modem:
a. Remove the screw of the modem cap (1x A1).
b. Slide open the modem cap and remove it.
Fig. 2: How to take out the modem.
c. Disconnect the modem connector cable.
d. Release the modem board like an SO-DIMM module.
e. Finally, take out the modem board.
A
Disassembly and Reassembly - 4
3. Memory
Next is described how to take out the memory module(s):
a. Remove the memory cap screw (A2) (see Fig. 1: ).
b. Slide the memory cap open.
c. Release the SO-DIMM memory module.
d. Remove the module.
Fig. 3: Removing the SO-DIMM module.
4. Front Cover
The front cover holding the touchpad should be removed according
to the next steps (also see Fig. 1: ):
a. Remove the three screws (2x B, 1xA3), which can be found on
the underside.
b. Lift up the front cover.
c. Disconnect the touchpad connector.
d. The front cover is now free from the notebook.
5. VersaGlide Touchpad
Disassemble the VersaGlide touchpad as follows:
a. Remove the flat cable of the touchpad buttons.
b. Disconnect the touchpad connector cable.
c. Remove the three button-board screws (3xC).
d. Remove the button board.
e. Carefully slide the touchpad frame down a little.
f. Push it upwards and take away the frame.
g. Lift up and take away the VersaGlide touchpad board
Note Take care that when placing the touchpad, the connector
on the touchpad board must face down, towards the buttons.
A
B
A
Disassembly and Reassembly - 5
Fig. 4: Underside of the Touchpad.
6. Hard Disk Drive
Here you can find the instructions for removing the hard disk drive:
a. Remove the two screws that hold the hard disk drive and it's
connector.
Note
During assembly the 3rd screw for fixing the HDD is inserted
during the assembly of the Front Cover.
b. Lift up the hard disk drive and remove it.
Fig. 5: Hard disk drive.
C
D
Disassembly and Reassembly - 6
7. HDD Bracket and Connector
These instructions explain how to remove the HDD bracket and the
HDD connector.
a. Remove the connector from the hard disk drive.
b. Remove the four screws (4xE) from the HDD bracket.
Fig. 6: Hard disk drive bracket.
8. Keyboard
Remove the keyboard as follows:
a. Slide the power-button cover (above the keyboard) slightly to
the right to unlock it.
b. Take away the power-button cover.
Fig. 7: Sliding off the power button cover.
E
Disassembly and Reassembly - 7
c. Lift the keyboard and disconnect the keyboard flat cable.
d. The keyboard is now free.
Fig. 8: Disconnecting the keyboard cable.
9. LCD Screen
Remove the LCD screen according to the following procedure:
a. Remove the two screws (2xA) on the back of the system.
Fig. 9: Removing the LCD screen (back)
b. Slide the LCD hinge covers outwards.
c. Remove the two screws (2xA) from the LCD cable box.
d. Remove the four screws on the LCD hinges (4xF).
Fig. 10: Removing the LCD screen (front).
A
A
F
Disassembly and Reassembly - 8
e. Take away the LCD screen.
10. LCD Panel Disassembly
Below you can find the complete set of steps required for
disassembling the LCD panel and all of its subcomponents:
a. Remove the small square stickers (2xH) to clear two screws
underneath.
b. Remove the two screws (2x J).
c. Remove the small rubber bumpers (2xG) at the top to clear two
screws underneath.
d. Remove the two screws (2x I).
e. Take off the LCD front bezel.
Fig. 11: Taking off the front bezel.
f. Remove the LCD lock and its spring.
g. Remove the single screw that holds the inverter-board (1xD).
h. Lift up the inverterboard and disconnect the two cables attached
to it.
i. Remove the screw (1xD) and the placeholder (1xK) for the cable
that runs to the inverterboard.
j. Remove the screw for the ground cable (1xI).
k. Remove the four screws from the LCD panel (4xL).
G
I
H
J
Disassembly and Reassembly - 9
Fig. 12: LCD screen disassembly.
l. Lift up the LCD panel from the back cover.
m. Remove the LCD cable connector from the back of the panel.
Fig. 13: Removing the LCD cable connector.
n. Remove the six screws holding the LCD hinges in place (6x J).
o. Take away the hinges.
Fig. 14: The hinges on the LCD back panel.
L
D
K
J
Disassembly and Reassembly - 10
11. Heatplate and CPU-Fan
Below you can find how to remove the heatplate:
a. Loosen the four screws of the heatplate.
Note The screws of the heatplate cannot be removed, as they
are locked in their position. They can only be loosened.
b. Take away the heatplate.
Fig. 15: Taking away the heatplate.
Note To securely re-seat the heatplate during (re-)assembly you
should first start with screw #1 then #2 etc…
c. Disconnect the fan power cable.
Fig. 16: The power fan cable and the DC/DC board screw.
D
Table des matières
Autres manuels NEC Ordinateur portable
NEC
NEC VERSA LXI#RELEASE NOTES Mode d’emploi
NEC
NEC VERSA SX HARD DISK DRIVE Manuel utilisateur
NEC
NEC VXI Series Manuel utilisateur
NEC
NEC VERSA ULTRALITE Manuel utilisateur
NEC
NEC VERSA SX HARD DISK DRIVE Manuel d'installation et d'exploitation
NEC
NEC VERSA 6060 WINDOWS 98 - UPGRADE INFORMATION Manuel utilisateur
NEC
NEC VERSA S5500 Series Manuel utilisateur
NEC
NEC VERSA VX Mode d’emploi
NEC
NEC VERSA N1100 Series Manuel utilisateur
NEC
NEC VERSA TXI Manuel utilisateur
NEC
NEC MobilePro 790 Manuel utilisateur
NEC
NEC VersaPro VB VG23T/B-T Manuel utilisateur
NEC
NEC VERSA TXI Mode d’emploi
NEC
NEC VERSA FXI Manuel utilisateur
NEC
NEC Versa LXi Manuel utilisateur
NEC
NEC Versa LX Manuel d'utilisation
NEC
NEC VERSA P600 Instructions d'installation
NEC
NEC VersaPro VB VC26M/BC-F Manuel utilisateur
NEC
NEC Versa LXi Manuel utilisateur
NEC
NEC VERSA LXI RELEASE NOTES Mode d’emploi
