NEC VERSA 4000 BATTERY CHARGER WITH AC ADAPTER Manuel utilisateur
NEC Versa 4000 Windows 98 Upgrade Information 1
NEC Versa 4000
Windows 98 Upgrade Information
Follow the instructions provided in this document to upgrade your
NEC Versa®4000 system to Microsoft®Windows®98.
Please read these notes in their entirety.
CAUTION
Although not a requirement, NEC recommends that you use
the system’s AC power adapter throughout this process. The
Windows 98 upgrade is somewhat lengthy and interrupting
the process with a loss of power can be catastrophic if the
system performs an emergency save-to-file.
Background
If you are using the FAT16 file-system format (16-bit based File Allocation
Table), then the “Save-to-Disk” functionality in the BIOS setup does not have to
be disabled.
At present, the “Save-to-Disk” power management feature of this system does
not fully function in Windows 98. It is very important that this feature be
disabled, particularly if you will be using the FAT32 file system. Instructions
for disabling “Save-to-Disk” are in the section below labeled, “Disabling the
Save-to-Disk in the BIOS Setup.”
Note:
To identify your computer’s file system format,
double click on the My Computer desktop icon. Next, right
click on the C: drive icon, and select Properties. If the
system is running FAT32, it is listed here next to “File
system.” If it is FAT16, FAT or FAT 16 appears.
CAUTION
Converting your hard drive to the FAT32 file system format
will significantly enhance file operations and save disk
space.
If you intend to convert your hard drive to the FAT32 file
system format, it is imperative that you disable “Save-to-
Disk” functionality in the BIOS setup.
Failure to do this can result in catastrophic data loss.
2NEC Versa 4000 Windows 98 Upgrade Information
System Requirements
The system requirements for your NEC Versa using Windows 98 are
approximately the same as they are for using Windows 95. As with Windows
95, Windows 98 requires 16 MB of RAM. For hard disk space, a typical
installation requires 225 MB of free hard disk space, but may range from 165
MB to 300 MB, depending on system configuration and options selected.
The system requirements for your NEC Versa are:
A minimum of 16MB of RAM.
Approximately 50 MB additional hard disk capacity.
If backing up Windows 95 system configuration files, another additional
50 MB for a total of 100-MB additional hard disk space.
Note:
The Windows 98 Setup Wizard informs you if
your system has insufficient hard drive space to proceed.
NEC recommends that you do the following procedures in the order listed to
upgrade your system.
1. Disable the “Save-to Disk” feature in the BIOS setup.
2. Upgrade your operating system to Windows 98.
3. Upgrade your mouse driver.
Disabling Save-to-Disk in the BIOS Setup
Follow these steps to disable “Save-to-Disk” in the BIOS setup.
1. Boot the system and enter the BIOS setup utility by pressing the F2 key, as
indicated on the screen, before Windows is loaded.
2. Once the BIOS setup utility is displayed, press the right arrow key 3 times in
order to display the “Power Savings” menu.
3. Press the down arrow to select the “Suspend Mode” row entry.
4. Press the plus (‘+’) to change the “Suspend Mode” setting to “Suspend” if it
is set to “Save to Disk.” (The default setting is “Suspend.”)
5. Press the down arrow to select the “Auto Save To File” row entry.
6. Press the (‘+’) to change the “On” setting to “Off.”
7. Press the right arrow key once to display the “Exit” menu.
8. Highlight “Save Changes and Exit” if it is not already selected.
9. Press the Enter key twice to save the settings and reboot the system.
NEC Versa 4000 Windows 98 Upgrade Information 3
Upgrading To Windows 98
Use these steps to upgrade from Windows 95 to Windows 98.
1. Insert the Windows 98 installation CD-ROM into your system. If your
system has Auto Insert Notification enabled, a Windows 98 graphic appears
asking you if you want to upgrade to Windows 98. If you see the graphic,
answer “Yes” and skip to step 3. If you do not see this graphic, continue to
step 2.
2. Use Windows Explorer to navigate to the Windows 98 Setup utility, at the
root of the CD-ROM drive. (Your CD-ROM drive will most likely be E:.)
3. Double click on the Setup icon. The Setup Wizard guides you through the
installation process. Answer all prompts appropriately.
Note:
You must to make three key decisions
depending on your particular needs and system
configuration. Use the following guidelines.
Concerning docking stations: You should perform the
Windows 98 upgrade in the mode (docked or undocked)
which you use most often. This is purely a decision of
convenience, as Windows 98 upgrades docking
configurations on an “as detected” basis.
Early during the Windows 98 upgrade process you are
prompted to decide if you want to back up your Windows
95 system files. Whether or not you backup your
Windows 95 system files is a judgement decision that is
left entirely to you. Just keep in mind that approximately
50 MB of hard drive space will be consumed by doing so.
Early during the Windows 98 upgrade process you are
prompted to make a Windows 98 bootable Startup
diskette, which loads CD-ROM drivers. If your system
cannot run both a floppy drive and a CD-ROM drive at
the same time, skip this section by selecting “Cancel” at
the “Insert diskette” screen. Later, when you have the
floppy drive installed, go to the Control Panel,
Add/Remove Programs, select the “Windows Setup” tab,
and create a startup diskette.
Upgrading the NEC Mouse Driver
When restarting your Versa computer using the Windows 98 operating system
in DOS mode, you may experience system problems. To prevent potential
system problems, install this updated version of the NEC Versa mouse
(VersaGlide) driver.
4NEC Versa 4000 Windows 98 Upgrade Information
Downloading the VersaGlide Driver
Follow these instructions to download the VersaGlide driver.
1. Create a temporary directory on your hard drive, for example C:\Mouse.
2. Access the NEC CSD Windows 98 upgrade page for the NEC 4000 systems.
3. Scroll down the page and click the driver file L6010FM3.EXE.
4. Save the file to the temporary directory.
Extracting the VersaGlide Driver
Follow these instructions to extract the VersaGlide driver.
1. Insert a diskette in drive A:.
2. Double click L6010FM3.EXE.
A message prompts you to insert a target disk to drive A:.
3. Press Enter.
The disk is formatted and the appropriate drivers are copied to the disk.
4. When the process is complete, close the DOS box.
Installing the VersaGlide Driver
Follow these instructions to install the VersaGlide driver.
1. Go to Start, Settings, Control Panel, and double click the Mouse icon.
Note:
If you cannot find Mouse Properties or if your
version does not have a Change option, refer to the
mouseini.txt file for "Installing from Device Manager."
2. Select the General tab, then click Change.
The Select Device screen appears.
3. Click Have Disk. The diskette is already in drive A:.
4. Confirm or correct the source file path (normally "A:\"), then click OK.
The Select Driver windows displays NEC VersaGlide.
5. Click NEC VersaGlide, then click OK to copy the driver files to your
system.
6. Click Close.
The System Settings change message prompts you to restart your computer.
7. Click Yes to restart your computer and activate the new mouse driver.
NEC Versa 4000 Windows 98 Upgrade Information 5
NEC Versa 4000
Windows 98 Upgrade Information
819-200542-000 Rev. 00
8/98
Autres manuels pour VERSA 4000 BATTERY CHARGER WITH AC ADAPTER
4
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels NEC Ordinateur portable
NEC
NEC Versa E3100 Instructions d'installation
NEC
NEC VERSA 4000 BATTERY CHARGER WITH AC ADAPTER Manuel utilisateur
NEC
NEC VERSA LXI - VERSION 10-2000 Manuel utilisateur
NEC
NEC VERSA LXI#RELEASE NOTES Mode d’emploi
NEC
NEC Versa Series Manuel utilisateur
NEC
NEC VERSA FXI Manuel utilisateur
NEC
NEC VERSA S5500 Series Manuel utilisateur
NEC
NEC Versa LX Manuel utilisateur
NEC
NEC VERSA 4200 Manuel utilisateur
NEC
NEC VersaPro VG17H/BB-D Manuel utilisateur
NEC
NEC J6N Manuel utilisateur
NEC
NEC VERSA 6050MH - SERVICE Manuel utilisateur
NEC
NEC VERSA VX Manuel utilisateur
NEC
NEC VERSA 6220 - SERVICE Manuel utilisateur
NEC
NEC VERSA 2200 WINDOWS 98 - UPGRADE INFORMATION Manuel utilisateur
NEC
NEC Generation N3000 M760s Manuel utilisateur
NEC
NEC VERSA DAYLITE Mode d’emploi
NEC
NEC Versa P700 Instructions d'installation
NEC
NEC VERSA P600 Instructions d'installation
NEC
NEC VERSA 2000 WINDOWS 98 - UPGRADE INFORMATION Manuel utilisateur
