National Instruments PXI-8109 Manuel utilisateur

INSTALLATION GUIDE

NI PXI-8109 and NI PXIe-8133

Flex Cable Replacement

This guide describes how to install the flex cable replacement for the

NI PXI-8109 and NI PXIe-8133 embedded controllers. For more detail and

a video demonstration of the cable replacement, please visit ni.com/info

and enter the Info Code 8133FlexReplace.

The flex cable can be replaced by hand. No tools are needed and the

controller does not need to be disassembled. Perform the following steps

for installation and removal instructions.

1. Locate the single-ended board to board flex cable on your

NI PXI-8109 or NI PXIe-8133 embedded controller as shown below in

Figure 1.

Figure 1. View of the Controller Back End with Board to Board Flex Cable

Caution Touch the metal part of the case to discharge any static electricity that might be

on your clothes or body.

1 Board to Board Flex Cable

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle

logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at

ni.com/trademarks for other National Instruments trademarks. Other product and company

names mentioned herein are trademarks or trade names of their respective companies. For patents

covering National Instruments products/technology, refer to the appropriate location: Help»Patents

in your software, the patents.txt file on your media, or the National Instruments Patent Notice

at ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/

export-compliance for the National Instruments global trade compliance policy and how to

obtain relevant HTS codes, ECCNs, and other import/export data.

*325798A-01*

2. Remove the existing cable by completing steps a and b below.

Caution Do not put pressure on additional components near the connector or scrape the

connector against components while removing the cable.

a. Gently remove by hand (no tools necessary) both sides of the

cable from the mating connectors on the two boards of the

controller.

1. Disconnect one side of the flex cable from its mating

connector.

2. Straighten the cable after disconnecting the first side.

3. Disconnect the second side of the flex cable from its mating

connector.

b. Discard the old cable.

3. Install the new cable.

a. The replacement cable will be flattened when it arrives.

b. Each connector is keyed in a way to prevent improper installation.

c. Connect one side of the new flex cable to the appropriate keyed

connector on the controller.

d. Slowly bend the cable using large angles such that the second flex

cable connector is above the mating connector on the controller,

and make the connection.

Caution Tight bends or creases in the cable will damage its functionality.

e. Once both sides of the cable are in place apply moderate pressure

on both sides to ensure a good connection. Do not push on other

components in the process. You may need to gently push the

middle of the cable toward the inside of the controller to square up

the connectors on the board.

4. Verify the cable is installed correctly.

a. Install the controller into a chassis.

b. Power on the chassis.

c. Verify the controller boots properly.

Autres manuels pour PXI-8109

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Contrôleurs

National Instruments

National Instruments NI 8350 Manuel utilisateur

National Instruments

National Instruments sbRIO-9637 Manuel utilisateur

National Instruments

National Instruments cRIO-9064 Manuel utilisateur

National Instruments

National Instruments cDAQ-9133 Manuel utilisateur

National Instruments

National Instruments cRIO-9030 Manuel utilisateur

National Instruments

National Instruments PXI Express Series Manuel utilisateur

National Instruments

National Instruments NI cRIO-9065 Manuel utilisateur

National Instruments

National Instruments PXIe-8100 Manuel utilisateur

National Instruments

National Instruments sbRIO-9628 Manuel utilisateur

National Instruments

National Instruments NI PXIe-8840 Manuel utilisateur

National Instruments

National Instruments FELDPoint FP-2000 Manuel utilisateur

National Instruments

National Instruments GPIB-232 Manuel utilisateur

National Instruments

National Instruments PXI-8109 Manuel utilisateur

National Instruments

National Instruments 7330 Manuel utilisateur

National Instruments

National Instruments NI-7931 Manuel utilisateur

National Instruments

National Instruments NI 9683 Manuel utilisateur

National Instruments

National Instruments NI PXIe-8135 Manuel utilisateur

National Instruments

National Instruments cRIO-9037 Manuel utilisateur

National Instruments

National Instruments RMC-8354 Manuel utilisateur

National Instruments

National Instruments NI PXIe-8133 Manuel utilisateur

National Instruments

National Instruments 73 Series Manuel utilisateur

National Instruments

National Instruments sbRIO-9605 Manuel utilisateur

National Instruments

National Instruments cRIO-9033 Manuel utilisateur

National Instruments

National Instruments NI PXIe-8840 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur