NAPCO GEMINI-P400 Manuel utilisateur

Using Your GEM-P400 Security System

ARMEDSTATUS

H 1 2 3 4

This page left blank intentionally

Congratulations on your purchase of an advanced GEMINI-P400 Security System. Meticulously developed by a leading

manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some

of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with

very easy, intuitive use. Please carefully review the information contained in this manual, so that you and all potential users of the

system familiarize yourselves with its operation, and can therefore take full advantage of GEMINI’s many convenience features and

amenities.

Your system consists of a control panel (a computer housed within a white metal panel enclosure), one or more GEMINI Decorator

Keypads for controlling the system, and various security detection devices. These detection devices are divided among separate

areas known as “zones”, set up throughout your premises. Each zone number corresponds to a Zone light on your Keypad’s display

area.

When a zone’s number is ON (or lit), it indicates that one or more detection device(s) assigned to that area are active or open. For

example, if Zone 1 is the front door, and it is open, the 1on the keypad display will be lit. If zone 2 is a motion detector, and there is

movement in that area, 2will light. Depending upon the actual layout your security professional has chosen to properly protect your

premises, each zone may function a little differently: The zone protecting your front door may be programmed as an Exit/Entry zone to

allow you time to enter the premises and disarm the system, without inadvertently sounding the alarm. Alternatively, a zone protecting

a window could be designated as an “instant” zone, so that if it is entered or opened while the system is on/armed, there will be an

immediate alarm.

Your easy GEMINI Keypad puts super-simple system control at your fingertips. Most keypad commands involve entering

your four digit User Code. This includes Arming (or activating) and Disarming (or deactivating) the system. Simply put, ARMED

means the system is ON; DISARMED means the system is OFF. If the system is OFF and you want to turn it ON, just enter your

Code. To turn the system back OFF, enter your code again. It’s easy, just always remember, in the event of an alarm, entering

your User Code will silence all Sirens. Your keypad is your command and status center, it keeps you informed visibly, using its

zone and status lights and audibly, using its built-in keypad sounder. For more information, please see Keypad Controls and Indicators

on page 5.

Introduction

System Information

Central Station Phone Number:________________________

Central Station Account Number: ______________________

For Service Call: ___________________________________

Entry Delay: _______________________________________

Exit Delay: ________________________________________

Alarm Time-Out:____________________________________

Table of Contents

Keypad Controls and Indicators ........................................5

Arming your System (When Leaving) ...............................6

Protecting Yourself While Home ........................................7

Emergency Keys ...............................................................8

Disarming the System ........................................................9

Silencing an Alarm .............................................................9

Special Functions.............................................................10

System Troubles ..............................................................11

Programming User Codes................................................13

Glossary ...........................................................................14

Important - Test Your System Weekly !

1Bell / Battery Test

Test your bell or siren by pressing Afollowed by 1. The bell

or siren will sound for 2 seconds and the battery will also be tested.

2 Zone Test

Walk throughout the premises opening each protected door or window,

and activating each motion sensor. Check the keypad to see that each

respective zone number displays in the window.

3Central Station Communication Test

(This test should only be performed on weekends or at a time

designated by your alarm company)

1. Notify Central Station of the impending test.

2. Secure all zones to light Status Light on your keypad.

3. Enter your User Code followed by Dto Arm the system.

4. Violate your alarm by opening a window / door etc.

5. The siren or bell should sound and the system will send the alarm

signals to the Central Station

6. Enter your User Code followed by Dto silence the alarm.

7. Call Central Station to insure that the alarm signals were received

properly.

ARMEDSTATUS

H1 2 3 4

Keypad Controls and Indicators

Trouble Light Hwill light and the Keypad

sounder will pulse to indicate that a system trouble

is present. (See System troubles, Page 11)

Status Light will light when all zones are

secure and system is ready to be Armed.

Armed Light will light when system is Armed,

and will flash when system is in Alarm

Press Afollowed by the corresponding

Function number to enable special functions

and options. (See Special Functions, Page 10)

To Bypass a zone, press Band the zone

number to be bypassed, and then Arm system.

Press Cto reset Fire Zone, clear miss-

entered codes, reset Alarm Memory, etc.

Numerical

Keys 1-9, 0.

Used to

enter User

Codes, Zone

numbers,

etc.

Emergency Keys Press simultaneously

to signal an emergency condition.

Press:

8+ Gfor Auxiliary Emergency or

9+Gfor Police Emergency.

(Programmable)

Zone Lights (1 through 4) will light to indicate

that the corresponding Zone is open, and will

flash to indicate a zone in alarm.

Press E

to bypass all

interior

protective

devices such

as motion

sensors, etc.

Press D

after entering

User Code

when Arming

or Disarming

System.

Press F

to remove

entry delay

from the Exit/

Entry door.

Arming Your System When Leaving

1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are

secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding. If any

zones cannot be secured, see Bypassing zones below.

2 Enter your user code and press D.The green Status light will go out, the red Armed light will light.

•If you make a mistake entering your code, press C, re-enter the code and press D.

3 Leave the premises through the Exit/Entry door. If the keypad gives a steady tone you have taken too long. Enter your

code again to disarm system and then re-enter code and leave.

Easy Arm

The optional Easy Arm feature allows the system to be armed by simply pressing D.This will allow the easy arming of the

system by someone who is not a regular system user.

Bypassing Zones

If an open zone cannot be immediately fixed, it can be left unprotected, or bypassed ,while the rest of the system is Armed.

To bypass a zone:

1 Press Bfollowed by the number of the zone to be bypassed. The bypassed zone’s number will flash slowly.

2 Enter your user code and press D.The green Status light will go out and the red Armed light will light.

3 Leave the premises through the Exit/Entry door.

When the system is subsequently disarmed, all bypassed zones will be reset, ready to be armed again. If it is necessary to

bypass any inoperative zone(s), it is important to have the zone(s) repaired as soon as possible.

A bypassed zone does not provide any protection, compromising system security.

Arming Your System

Protecting Yourself While at Home

1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are secure. If

any zones are open, the corresponding zone number will be lit. Secure those zones before proceeding.

2 Enter your User Code and press D. The green Status light will go out, and the red Armed light will light.

3 Before your exit delay expires, pressBto bypass any interior zones, deactivating devices such as motion sensors, and

allowing free movement throughout the premises. The Zone light of any bypassed zones will flash slowly.

Your system may have been programmed for Automatic Interior Bypass, in which case it will detect that you have not left the

premises and will automatically bypass any interior zones.

Instant Mode

Pressing Fwill cancel the Entry delay, activating the “Instant” mode. This is typically done in the evening when all family

members are home for the night. Instant Mode can be activated at any time after the system has been armed. The red Armed

light will flash rapidly while in the Instant Mode.

Easy Exit (optional)

Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises with the system armed. By

pressing Afollowed by 0, the protection is removed from the Exit/ Entry zone for 3 minutes.

This will allow, for example, an early morning commuter to exit the house in the morning, without having to disarm and rearm the

system, waking the family.

Arming with a System Trouble Present (TROUBLEHis lit)

If the GEM-P400 has a system trouble present, TROUBLE Hwill be lit and the keypad sounder pulsing. If you cannot immediately

clear the trouble, the system can still be armed. Simply press Afollowed by4to view the trouble.

Press Eto view any other troubles, and exit the TROUBLE mode when done. Enter your User Code and press Dto arm the

system. For more information, refer to page 11. Note: System troubles should be repaired as soon as possible.

Arming Your System

Emergency Buttons 89G

The three sets of emergency buttons, if programmed, are always active whether the system is

armed or disarmed. Discuss these Buttons with your installer. The emergency signal will only be

activated when the two respective buttons are pressed at the same time.

Auxiliary Alarm: Simultaneously press 8+Gto alert the central station of an

auxiliary emergency, if so programmed.

(The nature of this emergency alarm is to be determined by the installer).

Police Emergency: Simultaneously press9+Gto sound a police emergency alarm,

and to alert the central station of a Police emergency, if so programmed.

Emergency Conditions

Ambush Alarm

In the event that you are forced by an intruder to disarm your system, the ambush alarm can be

activated. Disarming the system with the Ambush Code will cause the system to disarm and

simultaneously send a silent ambush alarm signal to Central Station. If your system has the

Ambush feature enabled, the code assigned as the User 4 code will function as your Ambush Code.

8+G

Auxiliary Emergency

Enabled?

YES NO

9+G

Police Emergency

Enabled?

YES NO

Ambush Alarm

Enabled?

YES NO

Disarming Your System when Returning

1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the

system before your Entry Delay time expires.

2 Enter your User Code and pressD. The red Armed light will go out, indicating that the system has been disarmed.

Note: If you make a mistake entering your code, press Cand re-enter the code, followed by D.

Alarm Indication

If the Red Armed light is flashing rapidly, an alarm occurred while you were away. Proceed with caution!

For your own protection, leave immediately and call authorities from a neighbor's phone.

Silencing an Alarm

In the event that the system goes into alarm due to a violated burglary zone, the siren and the keypad sounder will activate

and the number of the zone in alarm will flash in the display. To silence the system, enter your user code followed by D.

The keypad sounder and siren will silence, but zone in alarm will continue to flash.

Press Cto reset this alarm memory.

Disarming Your System / Silencing an Alarm

Special Functions

By pressing Afollowed by the the appropriate key, (do not press simultaneously) these special functions and

features can be enabled:

Easy Arm (when system is disarmed)

The Easy Arm feature allows the system to be armed

pressing Afollowed by 0. This will allow the easy

arming of the system by someone who is not a regular

system user.

Easy Exit (when system is armed)

This function (if programmed) allows an occupant to leave

the premises without disarming the system. Pressing A

followed by 0while the system is armed will start a 3

minute period, during which you can leave through the Exit/

Entry door.

Bell / Battery Test

Pressing Afollowed by 1will cause the bell, or

siren to sound for 2 seconds. This will also initiate a test of

your battery to make sure it is adequately charged. The

P400 also performs an automatic battery test very 24 hours.

Access Output

If programmed, pressing Afollowed by 3will

activate the Access Output which may be configured to open

a door strike, turn on lighting, or activate some other special

feature your installer has provided.

Display System Trouble

Pressing Afollowed by 4when TROUBLE His lit

will cause the system to display any current system troubles.

Pressing Ewill exit the Display System Trouble Mode.

Chime Mode On / Off

Pressing Afollowed by 5will activate / deactivate

the door chime. Activating this feature will cause any door to

beep the keypad sounder when it is opened.

Program Mode

Pressing Afollowed by 8will enable the “Program

Mode”, which will allow you to program and erase user codes

(see Programming user codes, page 14)

Keypad Sounder On / Off

Pressing Afollowed by 9will deactivate / activate

the keypad sounder, depending on its present state. By

deactivating the sounder on a keypad installed in a bedroom,

for example, you will only turn off that keypad’s sounder. All

other keypads on the system will still sound normally.

Table des matières

Autres manuels NAPCO Système de sécurité

NAPCO

NAPCO Continental Access SUPER TWO CICP1300IOCOMBO Manuel

NAPCO

NAPCO MAGNUM ALERT 825 SYSTEM Manuel utilisateur

NAPCO

NAPCO Commercial GEMC Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 900 SYSTEM Manuel utilisateur

NAPCO

NAPCO Magnum Alert-700 Manuel utilisateur

NAPCO

NAPCO Gemini GEM-X255 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT-825 Manuel utilisateur

NAPCO

NAPCO SECURITY COMMAND CENTER Manuel utilisateur

NAPCO

NAPCO MA3000 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 854 SYSTEM Guide produit

NAPCO

NAPCO Prima Manuel utilisateur

NAPCO

NAPCO FREEDOM64 Manuel utilisateur

NAPCO

NAPCO Freedom F-64 Manuel utilisateur

NAPCO

NAPCO XP-400 Manuel

NAPCO

NAPCO Magnum Alert-800 Manuel utilisateur

NAPCO

NAPCO EXPRESS XP-600 Manuel utilisateur

NAPCO

NAPCO MAGNUM ALERT 3000 FIRE ALARM Manuel utilisateur

NAPCO

NAPCO Magnum Alert-700 Guide produit

NAPCO

NAPCO F-TPG Manuel utilisateur

NAPCO

NAPCO STARLINK SL-1 FD-T Manuel utilisateur

NAPCO

NAPCO FREEDOM - Manuel utilisateur

NAPCO

NAPCO EXPRESS XP-600 Manuel utilisateur

NAPCO

NAPCO XP-400 Manuel d'installation

NAPCO

NAPCO XP-400 Express Series Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur