NAD MT1 Manuel utilisateur

®

MT 1 MEDIA TUNER

Mounting Instructions

MOUNTING INSTRUCTIONS FOR THE C375BEE

The MT1 is compatible with C375BEE. Using the supplied exible at cable

(FFC), DC power connector and screws, the MT1 can be installed in a C375BEE

by undertaking the following procedure.

Note that if the C375BEE has a PP375 Phono Preamplier Module already

installed, the MT1 and the PP375 can be linked together using the other

supplied FFC.

STEP 1

Pre-install the requisite cables to their respective connector points on the MT1

as shown. Connect the FFC to the MT1’s PHONO port only if the C375BEE has a

PP375 already installed.

STEP 2

Make the following connections:

1 DC POWER connector from MT1 to corresponding P216B in C375BEE’s main

board.

2 FFC from MT1’s ANALOG OUT to P213B on C375BEE’s main board.

3 If the optional PP375 module is installed: FFC from MT 1’s PHONO port to

the corresponding FPC (exible printed circuit) connector of the PP375

module.

Ensure good harnessing by exing and safely contorting the FFC and

DCPOWER connectors.

STEP 3

Remove the dummy cover at the back of the C375BEE and install in its place the

MT1. Use the supplied screws to x into place the MT1.

3

2

1

IMPORTANT!

The MT1 is only compatible with C 375BEE units that have the

0.5Wstandby logo on their rear panels.

Copyright 2015, NAD Electronics International, a division of Lenbrook Industries Limited

All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.

No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

While every effort has been made to ensure the contents are accurate at the time of publication, features and specifications may be subject to change without prior notice.

MDCMT1_QS_V07  SEP 2015

1

2

MOUNTING INSTRUCTION FOR THE C356BEE

The MT1 is compatible with C356BEE. Using the supplied exible at cable

(FFC), DC power connector and screws, the MT1 can be installed in a C356BEE

by undertaking the following procedure.

STEP 1

Pre-install the requisite cables to their respective connector points.

Connect the following

1 DC POWER connector from MT1 to corresponding CB48 on C356BEE’s main

board.

2 FFC from MT1’s ANALOG OUT to CB36 on C356BEE’s main board.

Ensure good harnessing by exing and safely contorting the FFC and DC POWER

connectors.

STEP 2

Remove the dummy cover at the back of the C356BEE and install in its place the

MT1. Use the supplied screws to x into place the MT1.

NOTE

Download the latest MT1 owner’s manual from the Manuals/Downloads tab at

http://nadelectronics.com/products/hi-mdc-modules/MT-1-Media-Tuner-Module

Autres manuels pour MT1

1

Table des matières

Manuels Tuner populaires d'autres marques

Tunersys

Tunersys WS16 1 Manuel utilisateur

Arcam

Arcam DT91 Manuel utilisateur

Magnum

Magnum MD 102T Manuel utilisateur

HDHomeRun

HDHomeRun 20121008 Manuel utilisateur

Crestron

Crestron C2N-TXM Manuel utilisateur

Eico

Eico HFT-92 Manuel utilisateur

MFJ

MFJ MFJ-928 Manuel utilisateur

Sony

Sony ST-SA5ES Manuel utilisateur

Sirius Satellite Radio

Sirius Satellite Radio SC-FM1 Manuel utilisateur

Antique Automobile Radio

Antique Automobile Radio 283501B Manuel utilisateur

Monacor

Monacor PA-1200R Manuel utilisateur

Technics

Technics ST-X301L Manuel utilisateur

Manhattan

Manhattan 176156 Manuel utilisateur

Marantz

Marantz ST-15S1 Manuel utilisateur

Korg

Korg HA-40 Manuel utilisateur

Harman Kardon

Harman Kardon TU915 Manuel utilisateur

Teac

Teac T-1D Manuel utilisateur

Pioneer

Pioneer GEX-P700DAB Manuel utilisateur