NAD S170 Instructions d'utilisation et d'installation

Service Information S170

You may have a complaint about the S170 initialising. This may

be due to the power supply connector pins making poor contact.

To improve contact between the power supply and the pc board

perform the following .From the connector marked X27 ,the wires will have

to be soldered directly to the pins on the pc board . This is a 6 pin connector

with only 5 wires used. Unplug the connector from the board and cut the

wires from the connector. Strip and solder each power supply wire to its

corresponding pin labelled on the pc board. See diagram 1. Use heat shrink

tubing to prevent shorting the wires when soldering to the pins on the pc

board . I f the unit is received for general service this procedure should be

carried out.

Diagram 1

!THIS AREA OF THE CONNECTOR

POWER SUPPLY DO NOT TOUCH. X27

MAIN

Cut wires here PC BOARD

Strip and solder to pc board connector

ww

Contact:

NAD Electronics International

633 Granite Court

Pickering, ON Canada L1K 3K1

Voice: 905-831-0799 FAX 905-837-6357

www.nadelectronics.com

Red wire

Green wire

Green wire

Gray wire

Yellow wire

DGND

+5v

-15v

AGND

+15V

AGND

+5v adj.

Service Information S170

You may have a complaint about the S170 initialising. This may

be due to the power supply connector pins making poor contact.

To improve contact between the power supply and the pc board

perform the following .From the connector marked X27 ,the wires will have

to be soldered directly to the pins on the pc board . This is a 6 pin connector

with only 5 wires used. Unplug the connector from the board and cut the wires

from the connector. Strip and solder each power supply wire to its

corresponding pin labelled on the pc board. See diagram 1. Use heat shrink

tubing to prevent shorting the wires when soldering to the pins on the pc

board . I f the unit is received for general service this procedure should be

carried out.

Diagram 1

!THIS AREA OF THE CONNECTOR

POWER SUPPLY DO NOT TOUCH. X27

MAIN

Cut wires here PC BOARD

Strip and solder to pc board connector

ww

Contact:

NAD Electronics International

633 Granite Court

Pickering, ON Canada L1K 3K1

Voice: 905-831-0799 FAX 905-837-6357

www.nadelectronics.com

Red wire

Green wire

Green wire

Gray wire

Yellow wire

DGND

+5v

-15v

AGND

+15V

AGND

+5v adj.

Autres manuels pour S170

1

Table des matières

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur

Phonic

Phonic XP 3000 Manuel utilisateur

Rockford Fosgate

Rockford Fosgate Power T1500-1bd Manuel du propriétaire