MuxLab 500409 Manuel utilisateur

2321 Rue Cohen, Montreal Quebec, Canada. H4R 2N7

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: [email protected] URL: www.muxlab.com

Specifications

Environment

HDMI 2.0

Devices

DVD, plasma, projectors, monitors, TV,PC, laptops, servers

supporting HDMI.

Transmission

Transparent to the user

Bandwidth

594MHz

Signals

HDMI 2.0 and HDCP 2.2

Connectors

One (1) HDMI receptacle.

One (1) RJ45S for Cat 6a/7 unshielded or shielded twisted pair.

One (1) 3.5mm jacks for 1-way IR (emitter orsensor) (IR port

supports carrier wave from 38to 60KHz)

Note: HDMIcables not included.

Maximum Distance

Based on amaximum

length of 6.6 ft (2 m) of

HDMI cable per end.

30m (100ft) at 4K/60 (4:4:4) uncompressed over Cat 6a/7

40m (130ft) at 4K/30 (4:4:4) uncompressed over Cat 6a/7

45m (148ft) at 1080p/60 uncompressed over Cat 6a/7

Note: When installed in an electrically noisy environment, an

STP cable must be used. Also, cross-connection reduces the

effective distance depending on the grade oftwistedcable used.

RJ45 Pin Configuration

Reverse Polarity

Sensitive. Use EIA/TIA

568A or 586B straight-

through wiring.

RJ45 Link

Pin 1 (R) Pin 2 (T)

Pin 3 (R) Pin 6 (T)

Pin 4 (R) Pin 5 (T)

Pin 7 (R) Pin 8 (T)

Cable

One (1) Cat 6a/7 or bettertwisted pair cables required

Power Supply

One (1) 110-240V/12VDC @ 2A with blade US, UK, Euro

Power Consumption

6 Watts

Temperature

Operating: 0° to 40°C Storage: -20° to 70°C

Humidity: Up to 95% non-condensing

Enclosure

Metal black

Dimensions

90 x 44 x 23 mm

Weight

1.02 lbs.

Compliance

Regulatory: FCC, CE, RoHS

Warranty

2 years

Order Information

500409HDMI / Bi-IR Extender Kit

HDMI Extender Kit

500409

Quick Installation Guide

Overview

The HDMI 2.0 Extender Kit allows HDMI equipment supporting uncompressed video

up to 4K/60 (4:4:4) resolutions to be connected over Cat6a/7 unshielded twisted pair

cable in a point-to-point configuration at distances up to 30m at 4K/60, 40m at 4K/30

and 45m at 1080p. The unit supports HDCP 2.2, and audio pass-through up to Dolby

Atmos & DTS:X. The HDMI 2.0 Extender Kit supports a 1-way IR port (carrier wave)

for remote control of end devices. The kit comes with one (1) Transmitter and one (1)

Receiver as well as an IR Emitter and IR Sensor for remote control applications.

Applications

Applications include commercial and residential AV systems, classroom projector

systems, digital signage, boardroom systems, collaborative PC systems, and medical

information systems.

Installation

1. Identify the connectors on the Transmitter and Receiver as indicated on the product

labels.Verify that the distance between the HDMI Transmitter and Receiver is

within MuxLab specifications (see Specifications table).

2. To install the Transmitter:

2a Connect the Transmitter to the HDMI video source with an HDMI compliant

cable.

2b Connect one (1) length of Cat 6a (or higher) grade UTP cable to

RJ45 LINK connector on the Transmitter.

3. To install the Receiver:

3a Connect the Receiver to the HDMI display equipment with an HDMI

compliant cable.

3b Connect the one (1) Cat 6a (or higher) grade UTP cable to the RJ45

LINK connector on the Receiver.

4. This kit supports PoC, allowing the Transmitter to power the Receiver, or the

Receiver to power the Transmitter. Connect the 12VDC power supply to either the

Receiver or Transmitter first, and then plug the power supply into an AC power

outlet. If power is present, the blue power LED of the Transmitter and the Receiver

will be ON.

Note: Power the HDMI Extender only after all connections are made.

5. Power the HDMI equipment and verify the image quality.

6. Connect the IR Sensor to the 3.5mm Stereo Jack of the receiver and the IR

Emitter to the 3.5mm Mono Jack of the Transmitter.

Note: You can differentiate the IR Sensor and the IR Emitter by looking at the

3.5 mm plug. The IR Sensor is using a Stereo Plug (3 Contacts) and the IR

Emitter a mono plug (2 Contacts).

7. Position the IR Sensor so that it is directed to the hand-held remote control. For a

clear IR signal reception, aim the hand-held remote control to the top of the IR

Sensor enclosure.

8. Position the IR Emitter as close as possible to the source’s IR Sensor (i.e. DVD

player). For a clear IR signal reception, the IR Emitter can be glued on the source’s

IR Sensor. The IR Emitter’s signal is transmitted from the side of the enclosure.

9. If infrared remote control is needed to control the Display equipment from the

Source, connect the IR Emitter to the 3.5mm Stereo Jack of the receiver and the IR

Sensor to the 3.5mm Mono Jack of the Transmitter.

10. The following diagram shows the final configuration.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions

in respect to the installation of the HDMI Extender Kit:

Symptom

TX LED

RX LED

Probable

Cause

Possible

Solutions

Power/Link

No Image

OFF

No power

•Check power connections

No Image

UTP or HDMI Cable

•Check the UTP Or HDMI

cables.

No Image

Synchronization

•Check cable length.

Flickering

Image

Synchronization

•Check cable length

•Check the HDMI Cable

Quality.

Choppy sound

Synchronization

•Check cable length

•Check the HDMI Cable

Quality.

Green or pink

hue

DDC communication

•Cycle power of the HDMI

Extender.

•Check UTP cables and

replace.

Image flickers

when powering

up nearby

equipment

Interference

•Use STP cables

IR not

functioning

Interference from sunlight,

Fluorescent, Neon or Halogen lights

•Place the IR equipment

away for the interfering

light

IR not

functioning

Interference from RF radiation from

the TV

•Place the IR equipment

away for the RF radiation

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Autres manuels MuxLab Extenseur

MuxLab

MuxLab 500760-KVM Manuel utilisateur

MuxLab

MuxLab 500756 Manuel utilisateur

MuxLab

MuxLab 500730 Manuel utilisateur

MuxLab

MuxLab 500800 Manuel utilisateur

MuxLab

MuxLab 500462 Manuel utilisateur

MuxLab

MuxLab 500459-100 Manuel utilisateur

MuxLab

MuxLab 500070 Manuel utilisateur

MuxLab

MuxLab 500417 Manuel utilisateur

MuxLab

MuxLab 500417 Manuel utilisateur

MuxLab

MuxLab VGA Balun II Manuel utilisateur

MuxLab

MuxLab 500770-TX Manuel utilisateur

MuxLab

MuxLab 500752 Manuel utilisateur

MuxLab

MuxLab 500759-TX-HLO Manuel utilisateur

MuxLab

MuxLab 500458-ARC Manuel utilisateur

MuxLab

MuxLab 500754 Manuel utilisateur

MuxLab

MuxLab 500752 Manuel utilisateur

MuxLab

MuxLab 500464-V2 Manuel utilisateur

MuxLab

MuxLab 500464 Manuel utilisateur

MuxLab

MuxLab 500757 Manuel utilisateur

MuxLab

MuxLab 500752 Manuel utilisateur

MuxLab

MuxLab 500456 Manuel utilisateur

MuxLab

MuxLab 500402 Manuel utilisateur

MuxLab

MuxLab 500409 Manuel utilisateur

MuxLab

MuxLab 500752 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manuel utilisateur