MuxLab 500086 Manuel utilisateur

8495 Dalton Rd, Montreal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL: www.muxlab.com

Specifications

Environment

Digital Audio

Standard Supported

LPCM, Dolby Digital® 5.1, DTS, and Dolby® True HD

Input / Output signal

S/PDIF coax cable or TOSLINK optic cable, input selectable.

Sampling rate

Up to 96kHz/24bits

Maximum distance between

unit

500 ft. (150m)

Connectors

RCA, TOSLINK, POWER, RJ45 on each unit.

Power requirement

1W max, 5V DC

S/PDIF spec

Coax 75 ohm with RCA connector,

level: 500mVp-p into 75 ohm

TOSLINK spec

Plastic optic cable with EIAJ/JEITA RC-5720C connector,

Wavelength: red 660nm, level: -15dBm max.

Cabling Requirement

(not supplied)

Any 4-pair straight cable CAT5/5E/6 with RJ-45 connector.

Coax and second Optic Cable.

Included in this kit

1 x TX unit, 1 x RX unit, 1 x 5V Power supply,

1 x Optic Cable 3ft (1m) and 1 x Installation guide.

RJ45 Pin Configuration

Pair 4+5 (data), 1+2+7(+5V), 3+6+8(0V)

Compatible mounting

hardware

500902, 500900, 500910, 500915

Temperature

Operating: -40° to 85°C (-40° to 185°F)

Storage: -40° to 85°C (-40° to 185°F)

Humidity

Maximum 95% (non-condensing)

Enclosure

ABS UL94HB fire retardant plastic

Dimensions

2.25” x 2.25” x 1.0” (6 x 6 x 2.5 cm) each box.

Shipping Weight

1 lb. (450g)

Warranty

2 Years

Order Information

500086 Digital Audio Extender

DIGITAL AUDIO EXTENDER KIT

500086

Quick Installation Guide

Overview

The Digital Audio Extender allows one (1) source of digital audio signal: coax (S/PDIF)

or optic (TOSLINK) to be connected to a receiver: coax or optic to up to 500 ft. (150m)

in a point-to-point configuration. The Extender supports most standards to transmit two

channels of uncompressed lossless PCM audio or compressed 5.1/7.1 surround sound,

such as Dolby Digital Plus or DTS-HD High Resolution Audio (multichannel digital

audio Dolby Digital® 5.1, DTS, and Dolby® True HD).

Applications

Transmission of Digital Audio Signal

Installation

One source unit can be connected to one receiver unit using a CAT5/6 cable. To install

the unit, perform the following steps:

Caution: Do not attempt to open the housing. There are no user-serviceable parts

inside the unit. Opening the unit will void your warranty.

Do not connect the unit to a telecommunication outlet wired to unrelated

equipment. Making such a connection may damage the equipment and/or

the unit. Verify that the desired twisted pairs are not being used for other

LAN or telephone equipment.

1. Use a dedicated 4-pair Cat5e/6 cable between the source and the receiver unit.

2. Patch panels are compatible.

3. Verify the wiring is “straight-through”, has 4 twisted pairs and has the standard Ethernet

RJ45 connector.

4. Connect the 5V power supply to one side only. Any side can be used.

5. Connect the unit to the audio source, either by coax source or optic. On the source

side, select which type of input is used. Both sides can be connected but only one is

used to transmit audio. At the receiver side both outputs will contain the same

signal. Note that some AV system may require that you connect only one signal.

Troubleshooting

The following tables describe some of the symptoms, probable causes and possible solutions regarding

the unit:

Symptom

Probable Cause

Possible Solutions

No audio

No signal from source

Source off.

Power missing. Check led.

Check continuity on all pair.

Check if pairs are not swapped.

Check if the four pairs are present.

Malfunctioning unit.

Intermittent audio or

no audio

Cable too long

If you still can’t diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Table des matières

Autres manuels MuxLab Extenseur

MuxLab

MuxLab 500752 Manuel utilisateur

MuxLab

MuxLab 500459-100 Manuel utilisateur

MuxLab

MuxLab 500450-LR Manuel utilisateur

MuxLab

MuxLab 500451-POE Manuel utilisateur

MuxLab

MuxLab 500390 Manuel utilisateur

MuxLab

MuxLab 500756 Manuel utilisateur

MuxLab

MuxLab 500041-WP-UK Manuel utilisateur

MuxLab

MuxLab 500451-PoE Manuel utilisateur

MuxLab

MuxLab 500759 Manuel utilisateur

MuxLab

MuxLab 100504 Manuel utilisateur

MuxLab

MuxLab 500752 Manuel utilisateur

MuxLab

MuxLab 500760-KVM Manuel utilisateur

MuxLab

MuxLab 500754 Manuel utilisateur

MuxLab

MuxLab 500850 Manuel utilisateur

MuxLab

MuxLab 500070 Manuel utilisateur

MuxLab

MuxLab 500732 Manuel utilisateur

MuxLab

MuxLab 500710 Manuel utilisateur

MuxLab

MuxLab 500752 Manuel utilisateur

MuxLab

MuxLab 500115 Manuel utilisateur

MuxLab

MuxLab 500759-TX Manuel utilisateur

MuxLab

MuxLab ProDigital 500485 Manuel utilisateur

MuxLab

MuxLab 500758 Manuel utilisateur

MuxLab

MuxLab 500112 Manuel utilisateur

MuxLab

MuxLab 500402 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manuel utilisateur