Munters BA1701 Manuel utilisateur

1© Munters Corporation, July 2017 QM1154r5

Instruction Manual

BA1701 Series Baﬄe Actuator

Models: BA1701 • BA1701-30

Aerotech

Baﬄe Actuator

2QM1154r5

BA1701 Series Baffle Actuator

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing a Munters Baffle Actuator. Munters equipment is designed to be the highest

performing, highest quality equipment you can buy. With the proper installation and maintenance it will provide

many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

3 Munters Corporation, July 2017 QM1154r5

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Dimensions 4

2. Installation Instructions 5-8

3. External Cabling Methods 9-10

4. Electrical Wiring 11

5. Operation 12-13

6. Maintenance 14

7. Troubleshooting 15-17

8. Exploded View and Parts List 18-19

4QM1154r5

1.1 Parts List

Unpacking the Equipment 1.

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all

components for signs of shipping damage. Any shipping damage is the customer's responsibility and should be reported

immediately to your freight carrier.

1.2 Inlet Dimensions

Each BA1701 includes:

1 - Baffle Actuator

1 - Hardware Package (HP1032)

  

  

  

  

  

  

  

  

HP1032 for Baﬄe Actuator

ID Qty. Cat. No. Description

[A] 4 KS2463 1⁄4” x 1.5” Hex Lag Screw, ZP

[B] 2 AC1039 3⁄16” Cable Clamp, ZP

[C] 4 KN1001 1⁄4”-20 Hex Nut, ZP

[D] 1 AC1037 Cable Assembly, 60”L., 1⁄4”-20 THRD ENDS

[E] 1 AC1048 Thimble for 1⁄8” Dia. Cable, ZP

[F] 4 AC1286 3.5”Dia. Pulley w/ Hanging Bracket, CI

[G] 4 KS2650 5⁄16” x 5” Open Eye Lag Screw, ZP

[H] 2 AC1038 5⁄16” x 9” Hook & Eye Turnbuckle, AL/ZP

Actuator Speciﬁcations

Power: 110-120 VAC

Amps: 0.5

Phase: 1 Frequency: 60 Hz

Load Capacity: 700 lbs.

Note:

These actuators are designed to open or close Aero-Baffle accordingly from signals received from any one

of Munters Air-Monitor Controls or Environmental Computer Controls.

51⁄16”

75⁄8”

255⁄16”

5 Munters Corporation, July 2017 QM1154r5

Installation Instructions 2.

WARNING

High Voltage, disconnect

power before servicing.

Step 1

Install the actuator in the location shown on your ventilation system drawing

or as shown in Figures 1A and 1B. Secure to framing using (4) Lag Screws

[A]. See Figure 2A for typical installation of a ceiling mounted actuator.

See Figure 2B for typical installation of a wall mounted actuator.

Figure 1A

Figure 1B

6QM1154r5

Installation InstructionsChapter 2

         

              

  ! "

# $ % 

CEILING MOUNT

Figure 2A

SIDE VIEW

 &  % '    (  % %

) * + " ,

-  . /   ! " 0 .  &  % '    (  % %

) * + " ,

-  . /   ! " 0 .  &  % '    (  % %

 &  % '    (  % %

23⁄”

LOOKING UP FROM FLOOR

WALL MOUNT

Figure 2B

SIDE VIEW FRONT VIEW

  ! "

  

      

       

1 2 2  3  4 

 6

 3 

8 9

;

< =

E F

G I

8 9

;

< =

E F

 &  % '    (  % %

# $  %   

         

              

  ! "

  

      

       

1 2 2  3  4 

 6

 3 

7 Munters Corporation, July 2017 QM1154r5

Installation InstructionsChapter 2

Step 2

Fold Cable Assembly [D] in a “U” shape and insert 2 threaded ends through nylon block on end of actuator.

Pull 2 threaded ends through and attach to the Ball Nut Flange using (4) Nuts [C]. See Figures 3.

Figure 4

Figure 3

K L M N O P

O Q R S T U V V T W R S X N Y P

K X S Z [ \ S Z ] ^

U ] M L Q M Z _ ` Z L V a [ b

c d T [ e X T f Q b g ] _ T h N i P

j Q S S k Z d l S Q M T

lL S S T X N m P

j Q S S g M L n

Step 3

Secure Open Eye Lag Screw [G] to wall in direct line with BA1701. Then

attach Pulley [F] to Eye Screw as shown. See Figures 4.

\ Q S S K L M m S Q [ b T

8QM1154r5

o p q r s p t u v w x y z

Step 4

Unthread both ends of Turnbuckle [H] until they are 9” long, with an equal amount of threads showing at both

ends. Pull the cables attached to the baffle through pulleys and loop ends through eye of turnbuckle and secure

with Cable Clamp [B]. See Figures 5.

Installation InstructionsChapter 2

Figure 5

Figure 6

{ | s v w {v| } ~ x  z

|v v o  ~  v|  w

 ~ w r   w  | 

t q w  x  z

Step 5

Place Cable Thimble [E] over hook end of Turnbuckles [H]. Place Cable Assembly [D] in groove of Thimble [E].

See Figures 6.

|   w{ | s v w

|v v   p 

p v v w  x  z

o p q r s p t u v w x y z

{ | s v w {v| } ~ x  z

|v v o  ~  v|  w

 ~ w r   w  | 

t q w  x  z

|   w{ | s v w

|v v   p 

p v v w  x  z

{ | s v w    w }s v  x  z

o p q r s p t u v w 

{ | s v w

o   }s v w x  z

9 Munters Corporation, July 2017 QM1154r5

External Cabling Methods 3.

           

    ¡ ¢ £ ¤ ¤  ¥ ¦

     § ¨ ©  ¤ ¤ ª  ¤  « ¦

BAFFLE MACHINE AND CABLING WITHOUT HAND WINCH

Note:

When the baffle machine is connected directly to the

inlets, they will both travel at the same rate and the

normal load will be applied to the curtain machine.

Note:

When a Hand Winch is connected to the inlets and two free pulleys are connected

in line, the inlets will travel at the same rate as the baffle machine. For every 1” the

baffle machine travels the inlets will move 1”. The normal load will be applied to the

baffle machine.

¬ §  «   ¨ ª  ¤  « ¦

BAFFLE MACHINE AND CABLING WITH HAND WINCH INSTALLED

           

    ¡ ¢ £ ¤ ¤  ¥ ¦

     § ¨

¬ §  «   ¨ ª  ¤  « ¦

    ® £ ® ¯ ° ± ²  ³ ¤ 

´   ¡ ©    

µ § £ ¶ ¤   ¨   ¢ £ ¤ ¤  ¥ ¦

    ¡ ² « «    ®   «

¢ §   «

10 QM1154r5

· ¸ ¹ º » ¼ ¸ ½ ¾ ¿ À »

Á ¿ Â » Ã Ä Å Æ Æ » Ç È

· ¸ ¹ º » É Ê

Ë ¸ Æ Æ Ì À Æ » Í È

Î É Ï Í ¾ » Ê Ì À Æ » Í È

¼ ¸ Â ¿ Ð Å Ð Ñ Ò Ó Ô À Õ Æ »

Ö ¸ À Ã Ë ¿ À ½ ¾

Á Ê » » Ä Å Æ Æ » Ç

BAFFLE MACHINE AND CABLING WITH HAND WINCH INSTALLED

Note:

When a Hand Winch is connected to the inlets and a Free Pulleys is connected

to the baffle machine, the inlets will travel at twice the rate of the baffle machine.

This is because for every 1” the baffle machine travels the inlets will move 2”.

Twice as much load will be applied to the baffle machine, therefore, it will have

half the pulling capacity.

Note:

When a Hand Winch is connected to the baffle machine and a Free Pulleys is

connected to the inlets, the inlets will travel at half the rate of the baffle machine.

This is because for every 1” the baffle machine travels the inlets will move ½”.

Only half of the load will be applied to the baffle machine, therefore, it will have

twice the pulling capacity.

Baffle

¼ ¸ ½ ¾ ¿ À »

Á ¿ Â » Ã Ä Å Æ Æ » Ç È

Baffle

É Ê

Ë ¸ Æ Æ Ì À Æ » Í È

Î É Ï Í ¾ » Ê Ì À Æ » Í È

¼ ¸ Â ¿ Ð Å Ð Ñ Ò Ó Ô À Õ Æ »

Ö ¸ À Ã Ë ¿ À ½ ¾

Á Ê » » Ä Å Æ Æ » Ç

External Cabling MethodsChapter 3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Munters Contrôleurs

Munters

Munters Green RTU RX Manuel utilisateur

Munters

Munters SMART-8C Manuel d'instructions

Munters

Munters TRIO Manuel d'utilisation

Munters

Munters CCU5000 Manuel d'instructions

Munters

Munters Pig Guard Plus Expansion Manuel d'instructions

Munters

Munters Rotem Trio 20 Manuel d'utilisation

Munters

Munters Rotem Trio Manuel utilisateur

Munters

Munters MUX 2 Manuel d'instructions

Munters

Munters TRIO Manuel utilisateur

Munters

Munters Farm Center Manuel d'instructions

Munters

Munters Trio Poultry Controller Manuel utilisateur

Munters

Munters Farm Premium Manuel utilisateur

Munters

Munters TRIO Manuel utilisateur

Munters

Munters IA0090 Manuel utilisateur

Munters

Munters Platinum Touch Manuel utilisateur

Munters

Munters Rotem RBU-27 SE Mode d’emploi

Munters

Munters CO2 Sensor Manuel d'instructions

Munters

Munters Farm Center Pro Manuel d'instructions

Munters

Munters Element Manuel d'instructions

Munters

Munters G2 Manuel utilisateur

Munters

Munters Platinum Touch Manuel utilisateur

Munters

Munters TRIO Manuel d'utilisation

Munters

Munters MD2 Manuel utilisateur

Munters

Munters Green Field Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur