MULTISPAN DI-22U Manuel utilisateur
Terminal Connection:
ON OFF Delay Timer
DI 22U
Power Supply :
12V DC to 240V DC &
20 to 240V AC,50/60 Hz
Time Range : 0.1 sec to 10 Sec/Min/hour
Output:
1 Relay O/P (2 C/O, 5A 230 VAC)
KNOB
for time range setting
RELAY OUTPUT
PIANO SWITCH
for time range selection &
Delay on/off mode selection
MAIN LED
for visualisation of power
supply status
12V DC to 240V DC &
20 to 240V AC ,50/60Hz
Power Supply (A1 & A2) :
A1 25
26
28
16
15
18 A2
DI 22U
DI 22U
Supply Voltage
NO 1 NO 2
C1 C2
NC 1 NC 2
18 28
15 25
16 26
+
-
Dip switch selection:
Timing Diagram:
OFF ON
Switch
Settings
1 2 3 4
Switch 4
ON Delayed OFF
Delayed ON
OFF
Switch-1,2 & 3 for
time range selection
Switch 4 for Mode selection
ON
ON
ON
ON OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
1 Sec
10 Sec
30 Sec
100 Sec
10 Min
30 Min
100 Min
10 hrs.
ON
ON
OFF
OFF
OFF
OFF
SW 1
SW 2
SW 3
Multiplier
(Knob Indication) Range
0.1 Sec X 10
1 Sec X 10
3 Sec X 10
10 Sec X 10
1 min X 10
3 min X 10
10 min X 10
1 Hrs. X 10
t = Set Time
t t
t t
Power
ON Delay
OFF Delay
Terminal Connection:
12V DC to 240V DC &
20 to 240V AC ,50/60Hz
Power Supply (A1 & A2) :
A1 25
26
28
16
15
18 A2
DI 22U
Supply Voltage
NO 1 NO 2
C1 C2
NC 1 NC 2
18 28
15 25
16 26
+
-
Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
SAFETY PRECAUTION
All safety related codifications, symbols and instructions that appear in this operating
manual or on the equipment must be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might
impair the protection provided by the equipment.
90.00
47.00
22.5
66.35
NOTE:
All dimension are in mm.
WARNING GUIDELINES
WARNING : Risk of electric shock.
1. To prevent the risk of electric shock, power supply to the equipment must be kept OFF
while doing the wiring arrangement. Do not touch the terminals while power is
being supplied.
2. To reduce electro magnetic interference, use wire with adequate rating and twists of the
same of equal size shall be made with shortest connection.
3. Cable used for connection to power source, must have a cross section of 1mm or greater.
These wires should have insulations capacity made of at least 1.5kV.
4. A better anti-noise effect can be expected by using standard power supply cable for the
instrument.
Dimension
MECHANICAL INSTALLATION GUIDELINES
1) To install the instrument on a DIN rail, raise the clamp at the back of the instrument
and place it on the rail. Now release the clamp, so the instrument fits on the DIN rail.
2) Ensure proper fitting of the instrument by pulling it outwards.
3) To remove the instrument raise the clamp to release it from the DIN rail.
4) The equipment in its installed state must not come in close proximity to any heating
source, caustic vapors, oil steam, or other unwanted process byproducts.
5) Do not connect anything to unused terminals.
Product improvement and upgrade is a constant procedure.
Multispan reserves the right to change specifications without prior notice.Printing and typographical errors reserved.
Multispan Control Instruments Pvt. Ltd.
72/B,Phase 1, GIDC Estate,Vatva,Ahmedabad-382445,Gujarat,India.
Followus
+91-9978991476/9978991474/9978991482
INSTALLATION GUIDELINES
1. This equipment, being built-in-type, normally becomes a part of main control panel and in
such case the terminals do not remain accessible to the end user after installation
and internal wiring.
2. Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to
enter the product or else it may lead to a safety hazard that may in turn endanger life or
cause electrical shock to the operator.
3. Circuit breaker or mains switch must be installed between power source and supply
terminal to facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit
breaker must be installed at convenient place normally accessible to the operator.
4. Use and store the instrument within the specified ambient temperature and humidity
ranges as mentioned in this manual.
Table des matières
Autres manuels MULTISPAN Minuteur
MULTISPAN
MULTISPAN SQT-1044 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-4244 Manuel utilisateur
MULTISPAN
MULTISPAN DT 10S Manuel utilisateur
MULTISPAN
MULTISPAN UTR-2244 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-433 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-1033 Manuel utilisateur
MULTISPAN
MULTISPAN MDT-4310N Manuel utilisateur
MULTISPAN
MULTISPAN CYL-22 Feuille d'instructions
MULTISPAN
MULTISPAN SDX 22-02 Manuel utilisateur
MULTISPAN
MULTISPAN CYL-22U Manuel utilisateur
MULTISPAN
MULTISPAN MDT-4310 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-1244 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-2033 Manuel utilisateur
MULTISPAN
MULTISPAN FRT 22 Manuel utilisateur
MULTISPAN
MULTISPAN DIN-63 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-413 Manuel utilisateur
MULTISPAN
MULTISPAN DIN-63C Manuel utilisateur
MULTISPAN
MULTISPAN UTR - 1044 Manuel utilisateur
MULTISPAN
MULTISPAN UTR 1044 Manuel utilisateur
MULTISPAN
MULTISPAN UTR-1044 Manuel utilisateur
