MULTIGUARD Micro Manuel utilisateur

multiGuard® micro

Remote control and alarm via GSM

Manual

Ver. 2.02

Profort A/S • Gunnar Clausens Vej 3 DK 8260 Viby J • Tel. +45 70233600 Fax +45 70233601 • E-mail: [email protected] www.profort.dk

INDHOLD

1. SYSTEM DESCRIPTION...................................................2

2. MOUNTING ...................................................................3

Prepare the central unit ..................................3

Install SIM-card...............................................3

Electric mounting ............................................3

DIP switches for analog inputs........................3

3. PREPARE PC ..................................................................4

3.1 Connect PC ...............................................4

3.2 Set-up via USB-RS232 serial converter......4

3.3 Find Com-number .....................................4

4. INSTALLATION OF PC-PROGRAM ..................................5

5. SETTING UP WITH ”QUICK-SETUP” ...............................6

Window 1: Modem .........................................6

Window 2: Receiver(s) ....................................7

Window 3: Inputs............................................8

6. SETTING UP WITH SMS................................................13

Shift PIN-code ...............................................13

Lost password ...............................................13

Deactivate password.....................................13

Setting up receiver(s) ....................................13

Delete receiver ..............................................14

Setting up zone for receiver ..........................14

Approve telephone numbers.........................14

Change the priority of receivers ....................14

6.1 SETTING UP DIGITAL INPUT.......................................14

Set up text.....................................................14

Send alarm only if text is entered..................14

Set up zone for digital input..........................15

Use input 0 for connection/disconnection .....15

Set up filter on input .....................................15

Use input for counting pulses........................15

Activate 24V .................................................16

Execute command in text field......................16

6.2 SET UP ANALOG INPUTS ...........................................16

6.3 SETTING UP OUTPUT .................................................17

Activate output in case of alarm ...................17

Set up macro .................................................17

Record IR-code ..............................................18

Transmit IR-code ...........................................18

6.4 SYSTEM MESSAGES AND ALARMS ............................18

Acknowledge command................................18

Send alarm immediately on power failure.....18

Send status message.....................................19

Set time in the unit........................................19

Time controlled connection/disconnection ....19

Text to and from serial port (RS232) .............19

Data communication with PLC ......................19

6.5 COMMANDS FOR SET-UP ..........................................20

7. OPERATION................................................................. 26

Connect/disconnect the unit..........................26

Control by SMS..............................................26

Control by DTMF ...........................................26

Acknowledge alarm ......................................26

Requests to the unit ......................................26

Restore to default settings ............................27

9. FREQUENTLY ASKED QUESTIONS ................................29

10. SPECIFICATIONS........................................................ 31

multiGuard® micro

Remote control and alarm via GSM

Mounting

Ver. 2.02

1. SYSTEM DESCRIPTION

The unit is used for controlling relays and data/alarm-

transmission via the GSM-network. It contains GSM-

modem and a built-in antenna. Power supply: 8-24V

The unit can be set up with alarm texts of your own

choice via SMS or via the PC COM-port and the

enclosed ”Quick-setup” program.

Extra equipment:

•External antenna with 2,5 m. cable

(Profort no. 3690003)

•3,6V rechargeable LiIon battery

(Profort no. 009010)

•Temperature probe

(Profort no. 007995)

•Advanced PC-program “Basic” for many settings

on PC

(Profort no. 900902)

Functions

1 digital input

•Make (NC) / break (NO)

•Gnd/24V DC

1 analog input

•0-10 V

•0-20 mA

•PT100

•Profort temperature probe

•as digital input

1 Infra Red input

•Learns up to 10 IR-codes from a IR remote

control

Activation of 1relay-output

•Activate remotely with SMS and DTMF

•Activate as a function of input (from 10

sec. to 16 min. or follows input).

1 Infra Red output

•Transmits up to 10 IR-codes by SMS/DTMF

Forward alarms to max. 25 recipients

•as SMS messages

•as voice call with DTMF-tones

•as e-mail (depending on the telephone

company)

Calls 3 times in case of no answer.

Acknowledgement of alarm by pressing # during

the message (the call list will be interrupted).

Automatic alarm in case of sabotage and power

failure (also in disconnected state).

Back-up 14 days in case of power failure with

3,6V battery and in ‘sleep mode’.

Time functions:

Time based connection/disconnection

Time based status messages

Time registration in the log

Commands in the text for inputs

Alarm from 8 zones

Log: 256 records

Data communication with PLC via RS 232

Variable filter time for inputs: 10 sec. to 30 min.

Delay alarms for 30 sec. when connecting

/disconnecting the unit

Remote control of the unit with macros

System overview

multiGuard® micro

Remote control and alarm via GSM

Mounting

Ver. 2.02

2. MOUNTING

The unit has a built-in GSM-modem. All types of SIM-

cards can be used except from 3G cards. However it is

recommended to use a SIM-card “Pay and go”

instead of an ordinary SIM-card because the latter

often has an expiry date after e.g. 6 months.

Prepare the central unit

1. Lift the front cover of the unit.

The unit must be turned off!

2. Connect all relay-outputs and inputs to the unit.

Use at least 24 AWG – or stronger if possible.

Install SIM-card

3. Insert the SIM-card to be used

into a GSM-mobile phone.

4. Check that the SIM-card’s PIN

code is set to 1234 (default for

most telephone companies). If not, set the PIN

code to 1234 or deactivate the PIN code.

5. Check if it is possible to call from the card, and

send/receive SMS.

6. Remove the SIM-card fromf the GSM-mobile

phone and insert it into the GSM-unit.

7. Check that any inputs and relay-

outputs are properly connected

and place the front cover onto

the central unit again.

8. Connect the central unit to 230 VAC or

12-24 V AC/DC. Wait approx. 10 sec. while the

GSM-modem makes contact to the GSM-network.

When you hear 4 ’beeps’ and the red LED lights

continuously for approx. 20 sec. the unit is ready.

9. Send, if necessary, a SMS with ”1234 OK” to

get the GSM signal strength. It must be higher

than 25%.

Electric mounting

The unit can be mounted on a DIN-rail.

1. If the GSM-conditions are bad, replace the

internal antenna by an external antenna.

2. Mount, if necessary, 9V rechargeable battery.

3. Connect outputs:

Relay-outputs are potential free relay contacts that

break (NO) or make (NC) by means of instructions to

the unit. As default all relay-outputs are open.

4. Connect digital inputs:

Digital inputs are optocouplers. The inputs are

activated by 0V default (gnd) or 24 VDC on inputs

(can be changed in the set-up program). If the

supply is removed the inputs will deactivate. In both

cases an alarm can be sent from the central unit.

NB! Input 0 can also be used for

activating/deactivating the unit (toggle switch or

bell switch). Input 1 can be used for counting pulses.

GND or 24V on inputs, selected as option in the PC-

software.

5. Connect analog inputs:

As default the analog inputs function as ordinary

digital inputs (all Dip - switches off). If the analog

inputs are to be adapted to standard equipment: 0-

10VDC, 0-20 mA or PT100 probe, the Dip-switches

in the GSM-modem must be adjusted as illustrated

below.

DIP switches for analog inputs

Digital: Dip-switch 1-4 off

0-10VDC: Dip-switch nr. 1 on

0-20mA: Dip switch nr. 2 on

PT100: Dip switch nr. 3 on

Profort probes: Dip switch nr. 4 on

Each analog input has 4 Dip-switches.

Equipment and probes must be connected

between gnd and Ain1.

multiGuard® micro

Remote control and alarm via GSM

Prepare PC

Ver. 2.02

3. PREPARE PC

Start by connecting the serial converter and finding

the COM-port number on the PC.

3.1 Connect PC

1. Connect the COM-port output of the unit to

COM1 or the USB plug on the PC. Use a 9

pole serial cable or a USB to RS 232 serial

converter. The illustration below shows the

connections used in a RS232 cable.

Minimum requirements, PC:

Windows 95, 32 Mbyte RAM

Monitor, 800x600 screen

COM-port or USB-port

3.2 Set-up via USB-RS232 serial converter

When the USB cable is connected to the USB plug on

the PC Windows provides the PC with a COM-

number. A PC can have more than one COM-port,

and the actual COM-number provided by Windows

depends on which COM-port is used for setting up

the unit. Therefore it is necessary to check which

COM-number Windows has given to the selected

COM-port.

1. Install the driver enclosed with the USB-

converter and follow the instructions for this

product.

2. Connect the USB-cable to the USB-plug on

the PC.

Notice that the next time you connect the

USB-cable to either the same or another

COM-port the given COM-number can have

been changed.

3.3 Find Com-number

3. Select the menu START on your PC.

4. Select Control panel > System.

5. Select Hardware > and the first button

just below.

6. Select Ports.

Read the USB-to-Serial COM-Port.

multiGuard® micro

Remote control and alarm via GSM

Installation of PC-program

Ver. 2.02

4. INSTALLATION OF PC-PROGRAM

When the COM-no. is identified start the PC-

program for setting up the unit.

Install the set-up program on the PC:

1. Check that the COM-port output of the

unit is connected to COM1 or the USB

plug on your PC.

2. Insert CD-ROM in PC and click OK.

Windows suggests to install the setup-program

in C:\Programmes\Profort

To change this location, press Change Directory

and select the required folder.

3. Click the button in the upper left corner in

order to start the installation.

The installation runs automatically and

takes about 20 sec.

4. Start the setup-program on the PC. If the

text ”Version conflict” appears select the

latest version.

5. Enter the product key in the

window ’Product key’ which is automatically

displayed: The product key is written on the

cover of the CD-ROM.

If you have entered a product key to access

Quick-setup the screen below will be displayed:

6. Select the number of the COM-port to

which the unit is connected. If a correct

COM-port is selected the text

”Connection to multiGuard” in the

bottom

left corner will appear.

NB! If the text ”No Connection” appears

either a wrong COM-port is selected, the

unit is turned off or the RS232 cable is

defect.

If the text ’Connection to multiGuard’ doesn’t

appear, you have to check if

the correct COM-port has been selected.

7. Click the ‘Back’ button. Select

Communication port, only available

communications ports are listed.

8. Click the ’Next’ button and you will be

guided step by step through 4 setting

windows (see Setting up with Quick-

setup).

multiGuard® micro

Remote control and alarm via GSM

Setting up with

Quick set-up

Ver. 2.02

5. SETTING UP WITH ”QUICK-SETUP”

Start Quick set-up on the PC and follow the set-up instructions through the 4 windows. The settings will

be stored in unit’s ’flash memory’ and can be recovered in case of power failure. If the unit is coded

without a SIM-card the front cover must be removed.

Window 1: Modem

Present password: The password of the unit. When starting set-up the default password 1234 must be

applied. Remember that the PIN-code of the SIM-card in the unit also has to be

1234 when starting set-up.

GSM-number: Here the telephone number of the SIM-card in the unit is entered (optional unless the

clock-function is applied).

New password: Only numbers – not letters (4 digits). Here a new password, if required, is entered.

The PIN-code of the SIM-card will be changed similarly. If the password must be

deactivated the new password must be: 0000.

ID: Numbers or letters. Here an ID of the unit (max. 32 digits), if required, is entered.

Can be sent with all alarms.

NB! The password is applied for sending commands to the unit. The ID is transmitted

from the unit in case of alarm. If no ID is entered the password will also be the ID.

multiGuard® micro

Remote control and alarm via GSM

Setting up with

Quick set-up

Ver. 2.02

Window 2: Receiver(s)

It is possible to encode max. 25 receivers/ telephone numbers.

Forward alarms

Alarm messages can be forwarded as SMS, DTMF or E-mail. If you wish to receive both a SMS and an

analog voice message it is necessary to set up the same telephone number twice. A phone number can be

of max. 15 digits. An E-mail address can be of max. 48 characters.

Zone

In the field ’Zone’ (optional) is indicated whether all alarm messages are to be forwarded to the entered

telephone number or if this actual telephone number is to be called only in case of alarm from a specific

zone (0-7). Only one zone can be entered. If the same telephone number is to be called in case of alarm

from e.g. 2 zones the actual telephone number must be entered twice. If the field ’Zone’ is empty, alarm

from all zones will be received. The field ‘Zone’ disappears when the option ‘Approve’ is active.

Approve telephone numbers

If one or more telephone numbers are selected in the field ‘Approve’ the unit accepts SMS and analog

calls only from these numbers.

NB!: If the approved telephone number is not correct it is necessary to connect a cable in order to contact

the unit.

multiGuard® micro

Remote control and alarm via GSM

Setting up with

Quick set-up

Ver. 2.02

Window 3: Inputs

if the unit is not to be set up with user defined texts the unit will send the following standard messages in

case of alarm:

•S0: Make/close on input 0.

•B0: Break/open on input 0

If the unit is to be set up with user defined texts these can be encoded by means of the enclosed program

”Quick-setup”.

Text for inputs

In the window ’Inputs’ the text (max. 64 characters) to be displayed when an input changes position

is entered.

It is not necessary to enter a text also for closed position. That is if the activated relay is within a distance

of where it is possible to go inspect the problem. But it can be helpful if you are far away from the

activated relay and need a feedback on whether e.g. an irrigation plant has been inspected and again

functions normally.

If an alarm is to be sent only from the inputs which have a text, select either ‘ID + Text’ (return ID an

alarm text) or ‘Text’ (return only alarm text) in the field ‘Only send the alarm if text is entered’. Thereby

empty inputs will be filtered.

If ’Only send the alarm if text is entered’ is empty all alarms will be sent whether a text is entered or not.

multiGuard® micro

Remote control and alarm via GSM

Setting up with

Quick set-up

Ver. 2.02

Zone

”Zone” is optional and can be used for locating alarms in categories, e.g. some alarms in zone 1 and

other alarms in zone 2.

Filter

If “Filter” is selected, alarms will be sent only if the position of the input has been constant during the

filter time. See description of filter time below.

Analog input

The central unit has 1 analog input to which technical equipment can be connected in order to measure

an exact value, e.g. a temperature. In the field ‘Type’ select measuring equipment (0-10 V, 0-20 mA, PT

100, Profort 007995, Profort 007990). If the field ’Type’ is empty the analog inputs function as digital

inputs.

For 0-10V and 0-20mA the values for voltage and milliamp are optional for volt (fra –999 til +999). No

decimales.

Example:

In Scale (min max) define the values for 0V and 10V. ‘Min’ corresponds to 0V and ‘Max’

corresponds to 10V (default setting). Define e.g. that -20ºC corresponds to 0V and 60ºC corresponds to

10V. For the other measuring equipment in the list the values are already entered but can be modified.

In Alarm (min max) define the allowed interval. Define e.g. that min. is 0ºC and max. is 30ºC.

If the value gets higher or lower than the values in the Alarm (min/max) interval an alarm text (max. 64

characters) will be sent. For instance if the temperature drops below 0ºC or rises to 31ºC. The message

will be displayed in the inbox or on a mobile phone.

An Ok text (max. 64 characters) will be returned when the value is again between Alarm min. and max. If

information on a value is required, e.g. the temperature in a room, a request can be sent to the unit either

by SMS with the command V1 R

Set up input

’Input 0 used for connecting/disconnecting: Select how to change position on input. Either by using

‘Level’ (level control) or ‘Pulse’ (pulse control). If empty input 0 is a regular alarm input.

‘Input 1 used for counting pulses’: If selected input 1 is used for counting pulses. If empty

input 1 is a regular alarm input.

’Filter time’: Indicates a variable filter time for inputs. In the field ‘Filter’ for inputs is selected which

inputs are going to use the entered filter time. Select 10 sec., 20 sec., 40 sec., 1 min., 2 min., 4

min., 8 min., 15 min. and 30 min.

‘Only send the alarm if text is entered’: If a text is entered for inputs and wireless detectors, the alarm will

be sent. If there is no text, the alarm will not be sent. ‘ID + Text’: sends position, ID and text.

‘Text’: sends only text. The alarm text can be adapted to interface to pager systems or CCTV via

the serial port.

multiGuard® micro

Remote control and alarm via GSM

Setting up with

Quick set-up

Ver. 2.02

’Activate digital input’: The input can be set to GND or 24 VDC mode. In GND mode the input is activated

by a 0 VDC supply (GND) and input is closed. If the supply is removed inputs will open. In 24

VDC mode the input is activated by a 24 VDC supply and input will close. If the supply is

removed the input will open.

All digital inputs are either gnd or 24 VDC mode.

Activating commands in the text field

It is possible to enter one or more commands in the text field for digital and analog inputs so that a SMS-

message will be sent and at the same time a command will be carried out when the input changes it’s

position.

Commands in the beginning of the text field means that the command will be carried out also if the unit

is disconnected. If the command is at the end of the text field the command will not be carried out when

the unit is disconnected.

Example of a command in the text:

In this example the command OK means that the unit sends the actual GSM signal strength to all

telephone numbers when input 0 is open, e.g. by pressing a button. The receiver gets a SMS with the

signal strength in percent.

If no message is to be sent when input 0 shifts from open to closed position no text is to be entered in the

field ”Text when input is closed”.

Several commands must be separated

by a semicolon.

Commands start with < and ends with > ,

e.g.: <S0> will close relay.

Table des matières

Autres manuels MULTIGUARD Télécommande

MULTIGUARD

MULTIGUARD Light Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation

MULTIGUARD micro Manuel utilisateur

Manuels Télécommande populaires d'autres marques