Multicomp pro MP780052 Manuel utilisateur

Voltage Tester

Model No. MP780052

Read all instructions before using the appliance and retain for future reference.

• Please follow all safety operation instructions.

• Check probes and case insulation before using. If you find any breakage

or abnormality, or you consider the device is broken, stop using the device

immediately.

• Test using a known live source in the AC voltage range to confirm the tester is

working properly before use.

• Use caution with voltages above 30VAC as a shock hazard may exist.

• Insulation type and thickness and other factors may effect the operation, use other

methods to verify live voltages if there is any uncertainty.

• Do not use the product for any purpose other than that for which it is designed.

• Turn the tester off when not in use to save the battery.

• Remove the battery if the meter is not to be used for long periods.

• Replace the battery as soon as the low battery warning appears to avoid possible

electric shock or personal injury caused by incorrect readings.

PRODUCT OVERVIEW

WHAT’S INCLUDED

• Voltage Tester

• Batteries.

• Instruction manual.

IMPORTANT SAFETY INFORMATION

OPERATION

1. Screw on battery cover

2. Flashlight

3. Flashlight ‘on/off’ button

4. 12V mode button

5. Tester ‘on/off’ button

6. LED indicators

7. Detector tip

8. Worklight 1

234

• Turning the tester on: Momentarily press the tester On/Off button (5). The

sounder will beep once and the green LED will illuminate to indicate that the tester

is on and ready for use.

• Turning the tester off: Momentarily press the On/Off button. The tester will beep

twice and the green LED will turn off.

• Turning the sounder off: With the tester off, press and hold the On/Off button until

the green LED is illuminated. The tester will now operate without the sounder. To

turn the sounder off when the tester is on, press and hold the On/Off button until the

green LED flashes. To turn the sounder back on, press and hold the On/Off button

until the green LED flashes and the sounder beeps.

• Verify Operation: Before using tester, make sure the green LED is glowing and

check the tester on a known live AC voltage that is within the defined detection

range of the tester.

CLEANING

• Clean the tester with a clean, soft cloth.

• Do not use any chemicals, abrasives or solvents that could damage the tester.

MAINTENANCE

1. Carefully unscrew the battery cap at the rear (flashlight end) of the tester.

2. Replace the batteries with two AAA 1.5V batteries observing the polarity.

3. Carefully align the 2 flashlight contact springs on the cap with the contacts above

the batteries.

4. Press the cover onto tester and rotate clockwise until engaged. Do not use

excessive force.

5. The IP67 dust and water ingress protection level is

determined by the correct fitting of this cap.

NOTE: When batteries are loaded for the first time,

please remove the white, rectangular security strip

before installing the batteries.

• High Voltage Mode (200 to 1000V AC): Place the tip of the tester near an AC

voltage. If the tester detects voltage within the defined detection range, the green

LED will turn off, the red LED will turn on, and the sounder will beep rapidly.

• Low Voltage Mode (12 to 1000V AC): Press and hold the 12V button (4). The

green LED will change to yellow to indicate the tester is in the low voltage mode.

While pressing the 12V button, place the tip of the tester near an AC voltage. When

AC voltage is detected, the yellow LED will turn off, the red LED will flash and the

sounder will beep.

NOTE: The flash rate and beeping rate will increase as the tester gets closer to the

voltage source. If the tester detects high voltage, it will automatically change over to

the high voltage mode: The red LED will change to a steady glow and the sounder will

beep rapidly. The tester cannot determine the actual voltage. The voltage level where

the tester switches from the low to high voltage mode is effected by insulation type and

thickness, distance from the voltage source, and other factors.

• Low Battery Indication: Replace the batteries if the green LED does not turn on.

When the tester is on and the batteries are too low for reliable operation, the beeper

will beep three times and the green LED will turn off indicating the tester is not

operational. Replace the batteries to restore operation.

• Auto Power Off: To conserve battery life, the tester will automatically turn off after

approximately 5 minutes of inactivity. When powering down, the beeper will beep

twice and the green LED will turn off.

• Flashlight: Momentarily press the Flashlight button (3) to turn the flashlight

on or off. To conserve battery life, the flashlight will automatically turn off after

approximately five minutes. The beeper will beep twice as the flashlight turns off.

NOTE: If the battery voltage is too low to operate the flashlight, the tester will indicate

this condition by beeping three times and the flashlight will turn off. The voltage detector

has it’s own low battery threshold and may remain operational, verify it’s condition before

using the tester.

SPECIFICATIONS

Detection voltage ranges High: 200V to 1000V AC Low: 12V to 1000V AC

Frequency range 50/60Hz

Batteries Two AAA 1.5V batteries

Operating temperature 0°C to 50°C (32°F to 122°F)

Storage temperature -10°C to 60°C (14°F to 140°F)

Humidity 80% max

Altitude 2000 meters

Pollution Degree 2

Safety Compliance CAT IV-1000V

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &

ELECTRONIC EQUIPMENT.

These symbols indicate that separate collection of Waste Electrical and Electronic Equipment

(WEEE) or waste batteries is required. Do not dispose of these items with general household

waste. Separate for the treatment, recovery and recycling of the materials used. Waste batteries

can be returned to any waste battery recycling point which are provided by most battery retailers.

Contact your local authority for details of the battery and WEEE recycling schemes available in

your area. Made in China

LS12 2QQ

PO Box 13362 Dublin 2

Man Rev 1.1

Table des matières

Autres manuels multicomp pro Équipement de test

multicomp pro

multicomp pro MP720025 Manuel utilisateur

multicomp pro

multicomp pro MP720012 Manuel utilisateur

multicomp pro

multicomp pro MP720105 Manuel utilisateur

multicomp pro

multicomp pro MP740890 Manuel utilisateur

multicomp pro

multicomp pro MP720024 Manuel utilisateur

multicomp pro

multicomp pro MP72016 Manuel utilisateur

multicomp pro

multicomp pro MP720780 Manuel utilisateur

multicomp pro

multicomp pro MP720644 Manuel utilisateur

multicomp pro

multicomp pro MP720856 Manuel utilisateur

multicomp pro

multicomp pro MP720009 Manuel utilisateur

multicomp pro

multicomp pro MP780426 Manuel utilisateur

multicomp pro

multicomp pro MP700110 Manuel utilisateur

multicomp pro

multicomp pro MP720774 Manuel utilisateur

multicomp pro

multicomp pro MP780051 Manuel utilisateur

multicomp pro

multicomp pro MP760855 Manuel utilisateur

multicomp pro

multicomp pro MP Dual Channel Series Manuel utilisateur

multicomp pro

multicomp pro MP700499 Manuel utilisateur

multicomp pro

multicomp pro HDS-N Series Manuel utilisateur

multicomp pro

multicomp pro MP700005 Manuel utilisateur

multicomp pro

multicomp pro MP780833 Manuel utilisateur

multicomp pro

multicomp pro MP720645 Manuel utilisateur

multicomp pro

multicomp pro MP720854 Manuel utilisateur

multicomp pro

multicomp pro MP780834 Manuel utilisateur

multicomp pro

multicomp pro MP780050 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

multicomp pro MP780052 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques