Multiaqua CFFWA4P 04 Fiche technique

4-Pipe Universal Mount Fan Coil Unit

Please read this manual before using the fan coil unit.

Installation and service must be carried out by trained and qualified technicians only.

UNIVERSAL MOUNT

FAN COIL UNIT (4-Pipe)

________________________________________________________________________________

Operation and Installation Manual

CFFWA4P 04, 08, 12, 16 & 20

Rev. 1.3

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

GENERAL

Read the entire contents of this manual before beginning installation. Multiaqua assumes no responsibility for

equipment installed contradictory to any code requirement or installation instructions.

Careful attention has been given to the preparation of this IOM (Installation and Operation Manual) and the

content has been carefully compiled for your convenience. Dimensions were verified at the time of the writing

of this IOM. The manufacturer reserves the right to make changes for the improvement of products without

prior notice, therefore dimensions should always be field verified before the installation process begins.

The components of this unit have been inspected at the factory and readied for shipment. Upon receiving the

shipment, a visual inspection of the packaging must be performed. If any damage to the packaging is

discovered, an inspection of the components must be performed and noted on the delivery documents. If

component damage is found, a damage claim must be filed by the receiving party against the delivery party

immediately.

This product is designed and manufactured to permit installation in accordance with national codes. It is the

installer’s responsibility to install the product in accordance with national codes and/or prevailing local codes

and regulations.

Care must be taken to ensure the structural integrity of the supporting members, clearances, and provisions

for servicing, power supply, coil connections, and/or condensate removal. This unit is designed for a ceiling or

wall installation only.

The manufacturer reserves the right of change for the improvement of products without prior notice. Please

contact manufacturer or visit www.Multiaqua.com for the latest product information.

Recognize this symbol as an indication of important safety or

instruction related information throughout this publication.

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Table of Contents

INSTALLATION

Section 1. Inspection of Packaging 4

Section 2. Safety Precautions 4

Section 3. Operational Limits 4

Section 4. Selection of Installation Location 5-6

Section 5. Installation of the unit 7-9

Section 5a Ceiling Mounting

Section 5b Wall Mounting

DIMENSIONIAL DRAWINGS 10

FAN PERFORMANCE 11

PHYSICAL DATA 12

ELECTRICAL DATA 12

WIRING DIAGRAM 13

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Section 1) INSPECTION OF PACKAGING

1. It is advisable to place the unit close to the installation site without removing it from the package. Do

not put heavy tools or weights on the package.

2. Check the package to ensure no damage has occurred during transportation.

3. Check packaging for accessories inside the packaging materials before discarding.

4. Do not lift unit from packaging by the cover assembly, condensate, or by the water connections.

5. Remove cover assembly and lift the unit by the four corners of the unit body.

6. Once the unit is removed from the packaging, check and record the unit model and serial number for

future reference.

Section 2) SAFETY PRECAUTIONS

The appliance should be installed in accordance with NEC wiring regulations as well as, all mechanical codes.

1. When working on air conditioning equipment, observe precautions in this manual, and on all labels

attached to the unit.

2. Ensure that the electrical supply is the correct voltage required for your specific installation according to

the label on the equipment.

CAUTION: INSTALLING & SERVICING SHOULD BE CARRIED OUT BY TRAINED AND QUALIFIED SERVICE

PERSONNEL ONLY.

CAUTION: BEFORE STARTING ANY WORK, PUT ON ALL PERSONAL PROTECTION EQUIPMENT INCLUDING,

BUT NOT LIMITED TO, GLOVES AND SAFETY GLASSES REQUIRED FOR THE JOB.

CAUTION: BEFORE CARRYING OUT ANY WORK, TURN OFF THE MAIN POWER AT THE SERVICE

DISCONNECT AND FOLLOW ALL LOCKOUT- TAGOUT PROCEDURES.

Section 3) OPERATIONAL LIMITS

Power supply: Please refer to the label attached to the unit for correct power supply.

Minimum entering water temperature: 35.6°F

Maximum entering water temperature: 180 °F

Maximum water system pressure shall not exceed: 150 psi

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Section 4) SELECTION OF INSTALLATION LOCATION

1. Do not install the unit in rooms where any hazards are present which include, but are not limited to,

flammable gas, alkaline or acid substances, or where hazardous or corrosive atmosphere exists.

Aluminum/copper coils and/or internal plastic components can be damaged beyond repair. Cabinets are

internally insulated from the factory. However, when these units are installed in high ambient/high

humidity environments, additional external cabinet insulation may be required.

THESE UNITS ARE NOT RATED FOR EXPLOSION PROOF ENVIRONMENTS

2. Do not install in workshops or kitchens where airborne oil vapors or other chemicals may be deposited

on the coils, reducing the performance or damaging the internal plastic parts of the unit.

3. Choose a position near the wall as close to the center of the room as possible. See Figure 1

Figure 1

4. The installation location on the ceiling or wall must have

sufficient strength to carry the gross weight of the unit

listed in the table to the right. Mounting hardware

diameters listed are suggestions only Local code

requirements must he consulted by the installing

contractor.

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Section 4) SELECTION OF INSTALLATION LOCATION (continued)

5. Verify that the return grille (nothing within 36”) and supply louvers are not obstructed and the

conditioned air is able to circulate throughout the room. See Figure 2

Figure 2

6. Ensure there is sufficient space around he unit to service it. The dimensions shown in Figure 3 are

minimum suggestions. Your application may require more space to access controls, control valves, pumps,

or local code requirements.

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Figure 4

Section 5a) HORIZIONAL / CEILING INSTALLATION OF UNIT

1. For ceiling installation mark position of suspension rods, water pipes,

condensate drain, power supply cables, etc. Supporting rods can be fixed,

depending on the type of ceiling, as shown in Figure 4.

2. The casing is fixed to the slab with four (4) threaded rods. The rods should

have two (2) nuts and washers to lock the unit in position when using a

wooden or steel “trapeze style hanger”. See Figure 4. Installing

contractor may choose to use a field supplied, vibration elimination

solution on the hanging rods.

When lifting the unit into position, the unit must be supported

from end to end. Coil damage could result if this precaution is

not taken that is not covered by factory warranty.

3. Whenever the installation of the unit will be facilitated by using a lift,

the following precautions must be observed:

A. Remove the plastic return grille assemblies to protect it from

damage. This will be done by removing the filters and removing

two (2) screws in each section. See Figure 5

B. Insert plywood sheet between the lift and the unit so that the

unit will be protected while lifting the unit in place.

C. After the unit is secured to the lift, carefully lift the unit to the

ceiling.

4. Now that the unit is at ceiling height, attach threaded rods

to mounting brackets on the side of the unit. See Figure 6.

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Installation for all units

5. Ensure the unit is level, otherwise condensate water cannot drain properly.

6. Connect all supply and return water connections to the unit. It is recommended to use a vibration

eliminator, such as a flexible connector, to prevent the transmitting of vibration noise.

Connections can be routed either through the back/bottom panel or through the top/back of the

unit as illustrated in Figure 7 below. Locations of these openings are on the dimensional drawing.

Section 5b) VERTICAL / WALL OR UPFLOW INSTALLATION OF UNIT

1b. Unit can only be mounted with a top discharge or up flow in the vertical mounting

position.

2b. Wall construction as well as the fasteners used for wall/vertical mounting must be

capable of supporting the operational weight of the unit. The contractor and or

engineer on the job will be responsible for determining the need for reinforcements

that may be or may not be needed in the wall to support the operational weight of

the unit.

3b. When the unit is lifted into place the unit must be supported the entire length of

the unit to avoid coil damage during this process.

4b. Remember to allow 36” minimum from the front of the unit for service and good

return air flow.

The bottom of the unit will require 12” minimum of clearance to the floor for

service.

7. Connect the condensate drain to a gravity drain in compliance with all codes. After connection of the

chilled water and hot water lines, as well as the condensate drain, verify that the unit remains level.

All lines are to be insulated without air gaps in the insulation to

prevent condensation forming resulting in an undesired leak.

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

Figure 8

Figure 9

Section 5c) ELECTRICAL AND FRESH AIR INSTALLATION OF UNIT (Continued)

1. Make electrical supply connections in accordance with all code

requirements. Low voltage (24vac) and Line voltage connections

are located under the side cover on the left side of the unit when

facing in the direction of the airflow. See figure 8

2. Terminal strip configuration is

pictured here in Figure 9

3. Fresh air connections should be made at this time if applicable. There are no factory

predetermined connection locations for fresh air on the unit cabinet. Connections can be made

in the field by the contractor to the back or top of the unit into the fan compartment.

Contractor should supply and field fabricate boots for these connections to meet job

requirements as needed.

This source of fresh air MUST BE DELIVERED TO THE UNIT UNDER POSSITIVE PRESSURE as

these units are not rated for static pressure.

This source of fresh air must be turned off when the unit is not in operation to prevent

the introduction of unconditioned air into the conditioned space.

This source of fresh air must be filtered before delivery to the fan coil unit.

4. Reinstall filter grilles with the tow (2) screws in each section removed earlier. DO NOT OVER

TIGHTEN.

5. Unit is now ready for contractor start-up procedures and recording of benchmark data according

to all local and national requirements.

These specifications are subject to change without notice.

Check www.multiaqua.com for latest published information.

Fan coil unit - CFFWA4P Series

CFFWA4P Dimensional Drawing

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Multiaqua Ventilateur

Multiaqua

Multiaqua MHCFC4W-12 Fiche technique

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage