MUELLER CO. H-607 Manuel utilisateur

Mueller®H-607 Power Operator (Parker Motor)

GENERAL

Read and understand operation instructions for this tool before using it. Use

only parts approved by Mueller Co.

The H-607 Power Operator may be used to provide hydraulic power to drive

Mueller®CH-6, CL-12, and C1-36 Model #5 Large Drilling Machines.

OPERATING INSTRUCTIONS

Reliable Connections

Water (Canada)

1.705.719.9965

www.muellercanada.com

[email protected]

International

1.423.490.9555

www.mueller-international.com

[email protected]

DANGER

1. Failure to use hydraulic hoses

labeled and certied as non-

conductive when using hydraulic

tools on or near electrical lines may

result in death or serious injury.

Before using hoses labeled and

certied as non-conductive on

or near electrical lines, be sure

each hose is maintained as non-

conductive. Each hose should be

regularly tested for electrical current

leakage in accordance with your

safety department instructions.

2. A hydraulic leak or rupture may

cause oil injection in the body or

cause other severe personal injury.

a) DO NOT exceed specied ow and

pressure for this tool. Excess ow

or pressure may cause a leak or

rupture.

b) DO NOT exceed rated working

pressure of hydraulic hose used

with this tool. Excess pressure may

cause a leak or rupture.

c) Check hook, hose, couplers and

connectors daily for leaks. DO

NOT feel for leaks with your hands.

Contact with a leak may result in

severe personal injury.

d) DO NOT lift or carry tool by the

hose(s). DO NOT abuse hose. DO

NOT use kinked, torn or damaged

hose.

IMPORTANT

3. Make sure hydraulic hoses are

properly connected to the tool before

pressurizing system. Reversing

tool operation can result in severe

personal injury and/or equipment

damage.

4. DO NOT connect closed-center

tools to open-center hydraulic

systems. This may cause extreme

system heat and/or severe personal

injury.

DO NOT connect open-center tools

to closed-center hydraulic systems.

May result in loss of other hydraulic

functions powered by the same

system and/or severe personal injury.

5. Bystanders may be injured in your

work area. Keep bystanders clear of

your work area.

6. Wear hearing, eye, foot, hand and

head protection.

Water (U.S.)

1.800.423.1323

www.muellercompany.com

[email protected]

Gas (North America)

1.800.798.3131

www.muellergas.com

[email protected]

• Weight – 31 lbs. (14 kg)

• Length – 14” (36 cm)

• Width – 5” (13 cm)

• Height – 6” (20 cm)

SPECIFICATIONS

• Flow Range 7-9 gpm/ 26-34 lpm

• Motor Speed (without load)

61 rpm at 8 gpm

• Pressure 1500 psig (105 barg)

Mueller®H-607 Power Operator (Parker Motor)

Be sure to read and understand the

operating instructions for the Mueller

Drilling Machine used in conjunction with

the H-607 Power Operator.

To connect the H-607 Power Operator to

the Mueller Drilling Machine:

1. When using the CL-12 machine,

loosen the thumb screw holding the

lifting yoke and pivot in place. Remove

these parts for future use.

When using the C1-36 machine, loosen

the thumb screw on the pivot base

attached to the front bearing plate of the

drilling machine. Remove pivot and keep

for future use.

2. Position the H-607 Power Operator

over the pivot base and install the pivot

pin supplied with the H-607 Power

Operator.

3. Tighten the thumb screw to retain

the pivot pin.

4. Connect the H-607 Power Operator

to the hydraulic system, observing the

precautions provided on the previous

page.

The H-607 Power Operator MUST be

connected correctly to the hydraulic

system for the motor to turn in the

correct direction, and to prevent

possible equipment damage to the

motor or cutter, or severe personal

injury. The correct rotation is to drive

the machine spindle clockwise.

5. Turn on the hydraulic system and

momentarily activate the valve on the

H-607 Power Operator to allow the

motor drive square to align with the

square on the machine drive spindle.

The motor should drop into place.

6. Swing the eyebolt on the Drilling

Machine up between the ears on the

base of the H-607 Power Operator

– the washer should be on top of the

ears. Tighten the wing nut.

The directional control valve on the

H-607 Power Operator is detented,

and will remain in the ON position

when the valve lever is moved to the

ON position.

NOTE: Drilling machine must come

to a complete stop before reversing

direction of rotation. Failure to come

to a complete stop may damage

motor and/or machine and void

warranty.

OPERATION INSTRUCTIONS

The trademarks, logos and service marks displayed in this document herein are the property of Mueller Co., LLC, its affiliates or other third parties. Products marked with

a section symbol ( § ) are subject to patents or patent applications. For details, visit www.mwppat.com. These products are intended for use in potable water applications.

Please contact your Mueller Sales or Customer Service Representative concerning any other application(s).

Reliable Connections

Form 11903 – 06/17

Table des matières

Autres manuels MUELLER CO. Outils