MTX RANGER-10 Manuel utilisateur
MTX.COM
OWNER’S MANUAL
RANGER-10
POLARIS®RANGER®AMPLIFIED SUBWOOFER ENCLOSURE
MTX.COM
2
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support
at 1-800-225-5689.
When connecting power and ground wires ensure that the red power wire is fused at the point
where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a
short circuit develops between the vehicle connection point and the product.
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
• RANGER-10AmpliedSubwooferEnclosure
• EBC and EBC Extension Wire
• Mounting Hardware
Top Mounting Bracket
90°Bottom Mounting Bracket
M6 14mm Bolt with Washer and Lock Washer
5⁄16 Self-tapping Screws
ST6.3 25mm Self-tapping Screw
ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED
MTX recommends using StreetWires PS1K-10 amp kit which includes the following:
• Power and Ground Wire to Run to the Battery
• 20A ATC Fuse Holder
• Accessory Connection Wire
• RCA Cables to Connect to the Source
INSTALLATION TOOLS
The following is a list of suggested tools needed for installation:
• Torx - T40
• 3⁄8" Socket
• Flat Blade Screwdriver
• Pry Tool
• 1⁄8" Drill Bit
INTRODUCTION
ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris®
RANGER®.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris®
RANGER®. Congratulations and enjoy the ultimate audio experience with MTX!
FITS THE FOLLOWING VEHICLES
• RANGER®XP 570 / 900 (2014 and Up)
• RANGER®DIESEL (2014 and Up)
• RANGER®6X6 (2014 and Up)
• RANGER CREW®XP 570-6 (2014 and Up)
• RANGER CREW®XP 900-5 EPS / 900-6 EPS (2014 and Up)
• RANGER CREW®DIESEL (2014 and Up)
MTX.COM 3
FEATURES
• 10"All-WeatherAmpliedSubwooferEnclosure
• Integrated250-WattRMS/500-WattPeakPowerAmplier
• Integrated Power and Ground Connections
• Low Level Input with External Gain Control
• Dash Mount Bass Control Knob (Included)
• Mounts Underneath Driver’s Seat (2 Seat Model) or Underneath Driver’s Side Rear Seat
(4 Seat Model) - Direct Fit, No Cutting Required
SPECIFICATIONS
• RMS Power Handling: 250-Watts
• Peak Power Handling: 500-Watts
• Frequency Response: 31Hz - 130Hz
MTX.COM
4
INSTALLATION
Step 1 - Lift the driver’s seat up and remove the plastic tub. The tub will not be reused.
Step 2 - Remove the T40 screws from the driver’s side. The single cab RANGER uses four screws on
theoorarea,onescrewonthefrontfenderarea(thelowestscrew),andonescrewonthebackof
the side panel.
MTX.COM 5
The dual cab RANGERusestwoscrewsontheoorarea,onescrewonthefasciabelowtheseat,
and one screw on the back of the side panel.
Step 3 - Remove the front and rear locking pins.
MTX.COM
6
Step 4 - Loosenthepipeclamponthefuelllerpipewithaatbladescrewdriver.Thefuelllerpipe
should be able to be pulled from the rubber fuel pipe. Take care when doing so.
WARNING: Do not smoke during this step.
Step 5 - Carefullypullawaythesidepanelfromvehicle.Thegascap/fuelllerpipeisattachedto
the plastic side panel and will slide out of the rubber fuel pipe.
MTX.COM 7
Step 6 - Slide the long part of the enclosure into the vehicle frame above the gas tank. The subwoofer
will face the top of the gas tank. Two brass inserts will be visible when looking down from the top and
the MTX logo will be pointing towards the outside of the vehicle.
Step 7 - Remove the two T40 screws as shown above. These screws hold down the vehicle plastic
brace under the seat.
Step 8 - Line up the larger enclosure mounting bracket with the alignment holes for the vehicle
mounting screws. Using the T40 screws from Step 7 screw the bracket to the vehicle, hand tighten.
Attach the bracket to the two brass inserts in the top of the enclosure using the included M6 bolts
and washers, hand tighten.
MTX.COM
8
Step 9 - Line up the brass insert on the front of the enclosure with the hole in the vehicle frame. Using
the included M6 bolt and washer, attach the enclosure to the vehicle.
Step 10 - Tighten all M6 bolts into the enclosure as well as the T40 bolts holding the top enclosure
bracket to the vehicle.
Step 11 - The small 90°angle bracket attaches to the vehicle using the two pre drilled holes on the
frame. The two larger holes in the bracket are for the 5⁄16" self-tapping bolts. Secure the bracket to the
frame using the included bolts.Thebracketwillsitushwiththeenclosure.
MTX.COM 9
Step 12 - Attach the enclosure to the 90°angle bracket using the included ST6.3 self-tapping screws.
A 1⁄8" drill bit should be used to pre drill holes in the enclosure. Be careful not to strip them when
tightening into the enclosure material. Do not use an impact driver for these screws.
Step 13 -Now that the enclosure is securely tightened in place, the power and signal wires need to
be connected to the battery and signal source.
• The Red wire should be connected directly to the battery’s positive terminal and fused with a
20A fuse.
• The Black wire should be directly connected to the battery’s negative terminal.
• If your vehicle is equipped with the Polaris®busbar kit, the Red and Black wires can be
connected to the busbar under the hood. The Red wire will still need to be fused.
• The Blue wire can be connected to the ACC / Key Turn On located on the busbar of any vehicle.
Step 14 - Connect the RCA inputs to the signal source of your choice
Step 15 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot
that is attached to the orange/grey wires. Set the gain to the bass level desired.
Step 16 - The included EBC can be connected and mounted to a desired location to allow easy trim
adjustment of the bass level after the gain has been set.
Step 17 - Replace all the parts and screws that have been removed to return the RANGER back to its
completely assembled state.
MTX.COM
10
NOTES:
Table des matières
Autres manuels MTX Subwoofer
MTX
MTX JGC10A-T45 Manuel utilisateur
MTX
MTX LOLITA Manuel utilisateur
MTX
MTX Thunder 85 TS8512-22 Manuel utilisateur
MTX
MTX JackHammer Manuel utilisateur
MTX
MTX T4158A Manuel d'instructions
MTX
MTX Thunder TS8512-22 Mode d’emploi
MTX
MTX CT12SW Manuel utilisateur
MTX
MTX Thunder TR7510-22 Mode d’emploi
MTX
MTX X Thunder XT12-44 Manuel utilisateur
MTX
MTX MTX Thunder 4000 T4104A Manuel utilisateur
MTX
MTX Thunder T8510-44 Manuel utilisateur
MTX
MTX MTX Thunder 8000 T8154A Manuel utilisateur
MTX
MTX RTP8 Manuel utilisateur
MTX
MTX TSW10 Manuel utilisateur
MTX
MTX Thunder TR5512-44 Mode d’emploi
MTX
MTX Thunder TR7515-44 Mode d’emploi
MTX
MTX Thunder T8512-04 Mode d’emploi
MTX
MTX T41012A Manuel d'instructions
MTX
MTX Thunder TS8510-44 Mode d’emploi
MTX
MTX RTT12P Manuel utilisateur
