MSI MS-IO36 Manuel utilisateur
Installation Guide
Copyright © 2006 MSI Computer Corp.
Overview:
MS-1036 is shipped out as a bare bone. Some of the components are equipped while some are not. This
installation guide provides you with the information of notebook hardware setup. Before assembling your
Notebook, please prepare the installation tools and appropriate items. If you are not clear about the
items, please contact your dealer for more information.
Package check list:
Optional Hardware Devices:
HDD, Mini PCI WLAN card, CPU, Memory
Before installing Devices in Notebook
• The peripheral devices contained herein depend on your actual system configuration.
• Third-party trademarks and names are the properties of their respective owners.
• The information contained herein is relevant to software and hardware references only and in
accordance with actual system configuration. All information is subject to change without notice.
Warning!
• Ensure power is turned off and Notebook Battery is removed before installing any hardware
devices.
• Use a grounded wrist strap before handling any computer components such as CPU, Memory,
HDD, mini-PCI Card, etc.
• Place components (CPU, Memory, HDD, mini-PCI Card, etc) on a grounded antistatic pad or on
the foam bed that came with the components whenever the components are separated from the
Notebook.
• If there are any difficulties installing hardware devices, please contact your dealer for further
information.
Open View
1. Cover latch
2. Display Panel
3. Quick Launch Buttons and Power button
4. Status LEDs
5. Keyboard
6. Touchpad
7. Stereo Speakers
8. Web Cam
Bottom View
1. CPU Compartment
2. Mini PCI Drive Compartment
3. Memory Compartment
4. Hard Disk Drive Compartment
5. Battery Unlock Button
6. Battery Pack
Rear View
Right view Left view
Open View
Step 1: Installing CPU
1-1 Lift the metal lever up until it can go no further.
1-2 a.b. Locate the golden cut edge on the CPU’s lower left-hand corner. Then insert the CPU into the
Socket
!!!The CPU will only fit in the correct orientation!!!
1-3 a.b. Adjust the CPU socket raising the lever. Make sure the CPU is properly installed. Then press the
CPU evenly by hand and lower the lever to lock the CPU in place.
!!! Please make sure the golden cut edge location is aligned with the notch of the CPU socket. If
the CPU does not align with the CPU socket, it will damage the CPU!!!
Step 2: Installing CPU Heat Sink and Fan
2-1 Use the Heat Sink and Fan that is provided.
2-2a.b. Plug the CPU fan connector before positioning the fan.
!!! Connect the wires correctly. There is only one way to connect. DO NOT force in. !!!
!!! Warning: failure to connect the fan may cause damage to the CPU or the notebook!!!
2-3 Slide the CPU Heat Sink and Fan over the CPU.
!!! Be sure that there are no wires underneath the Heat Sink. !!!
2-3a.b.c. Align the three screws with the screw holes next to the CPU. May need to slide the Heat Sink to
the side to align. Tighten the three screws in 1-3-2 order.
!!! Improper connection of the CPU heat sink will damage the notebook and CPU!!!
Step 3: Installing Notebook Memory
3-1a.b. Align the memory module to the DIMM socket 1.
!!! Memory module can only fit in one direction due to the keyed notch. Wrong orientation will
cause improper installation and may damage the memory modules or DIMM sockets!!!
3-2 Push down the memory module gently until the metal-locking levers aside from the DIMM socket 1 is
fastened.
3-3 If you have more than one memory module, please repeat steps 3-1 and 3-2.
!!! Memory module can only fit in one direction due to the keyed notch. Wrong orientation will
cause improper installation and may damage the memory modules or DIMM sockets!!!
Step 4: Installing Mini PCI WLAN Card
4-1a.b. Align the Mini PCI Card to the Mini PCI socket.
4-2 Adjust the attached antennas and push down the Mini PCI Card gently until the metal-locking levers
aside from the Mini PCI socket is fastened.
!!! Mini PCI Card can only fit in one direction due to the keyed notch. Wrong orientation will cause
improper installation and may damage the Mini PCI card or Mini PCI socket!!!
4-3a.b. Connect the Black wire to the Main Connector.
4-4a.b. After connecting the black wire, connect the Gray wire to the AUX connector.
4-5a.b. After connecting both the black wire and gray wire, connect the short black wire to the Bluetooth
connector.
4-5a.b.c.d.e. After installing the CPU, Memory, and Mini PCI Card, gently slide the cover until it locks into
position. Lock down the cover by applying 4 screws.
Autres manuels MSI Ordinateur portable
MSI
MSI GF63 Thin 10SC Manuel utilisateur
MSI
MSI A13VF-012US Manuel utilisateur
MSI
MSI GF65 Thin 10SER-690 Manuel utilisateur
MSI
MSI FX620DX Manuel utilisateur
MSI
MSI GL63 8SE-056IT Manuel utilisateur
MSI
MSI X370 GAMING PRO CARBON Manuel utilisateur
MSI
MSI MS-1012 Manuel utilisateur
MSI
MSI GF65 Thin 10UE-010BE Manuel utilisateur
MSI
MSI Vector GP76 Manuel utilisateur
MSI
MSI CreatorPro M15 Manuel utilisateur
MSI
MSI CR630 Manuel utilisateur
MSI
MSI Prestige 16 Studio Manuel utilisateur
MSI
MSI L710 Manuel utilisateur
MSI
MSI MS-171F - Whitebook - 17 Manuel utilisateur
MSI
MSI GE70 MS-1756 Instructions d'installation
MSI
MSI GE603 Manuel utilisateur
MSI
MSI GX660R Manuel utilisateur
MSI
MSI A5EFK-076IT Manuel utilisateur
MSI
MSI Prestige 14EVO Manuel utilisateur
MSI
MSI GE66 Raider 10SGS-290IT Manuel utilisateur
