MP Aquinity2 P10 Manuel utilisateur

Aquinity² P10

User Manual

Editor:

membraPure GmbH

Wolfgang-Küntscher-Straße 14

D-16761 Hennigsdorf

Germany

Model: Aquinity² P10

Software: 2.1.10

Revision: 2

Date: 29.01.2019

Contents

1General................................................................................................................................ 1

1.1 About this manual....................................................................................................... 1

1.2 Symbols used in this manual...................................................................................... 1

1.3Liability and warranty.................................................................................................. 2

1.4 Copyright ..................................................................................................................... 2

1.5 Spare parts .................................................................................................................. 3

1.6 Disposal....................................................................................................................... 3

2Safety.................................................................................................................................. 4

2.1 Intended use................................................................................................................ 4

2.2 Contents of this manual.............................................................................................. 4

2.3 Changes and modifications to the equipment ........................................................... 5

2.4 User responsibility....................................................................................................... 5

2.5 Personal requirements................................................................................................ 5

2.6 Health and safety work ............................................................................................... 6

2.7 Personal protective equipment (PPE)......................................................................... 7

2.8 Potential hazards ........................................................................................................ 7

3System Features................................................................................................................. 8

3.1 General......................................................................................................................... 8

3.2 Series overview ........................................................................................................... 9

3.3 Technical data............................................................................................................. 9

3.4 Purification process and components ..................................................................... 10

3.5 Hardware ................................................................................................................... 12

3.5.1 Dispenser ........................................................................................................... 12

3.5.2 Control PCB (printed circuit board) ................................................................... 12

3.5.3 IEC Socket .......................................................................................................... 12

3.5.4 Front and side panels ........................................................................................ 13

4Installation and start up ................................................................................................... 14

4.1 Feed water requirements .......................................................................................... 14

4.2 Delivered parts........................................................................................................... 15

4.3 Setting up the system ............................................................................................... 15

4.4 Sealing plug............................................................................................................... 16

4.5 Connecting ................................................................................................................ 16

4.6 Module attachment................................................................................................... 17

4.7 Vent filter attachment ............................................................................................... 18

4.8 Sterile filter attachment ............................................................................................ 18

4.9 Electrical connection................................................................................................. 18

5System Control Panel....................................................................................................... 19

5.1 Normal operation mode ............................................................................................ 19

5.2 Tools .......................................................................................................................... 19

5.2.1 Changing the consumables............................................................................... 19

5.2.2 Changing the UV-lamp (in the pure water section) ........................................... 20

5.2.3 Change all Consumables ................................................................................... 21

5.2.4 Exporting Data.................................................................................................... 22

5.2.5 Prod. to max level .............................................................................................. 22

5.2.6 Process visualization......................................................................................... 22

5.2.7 Venting UPW ...................................................................................................... 23

5.3 History ....................................................................................................................... 23

5.3.1 Warning messages ............................................................................................ 23

5.3.2 Graphical values................................................................................................. 23

5.3.3 Logfile................................................................................................................. 24

5.4 User setup ................................................................................................................. 24

5.4.1 Limits setup ....................................................................................................... 24

5.4.2 System time settings......................................................................................... 25

5.4.3 Reset timers (manually)..................................................................................... 25

5.4.4 Operating hours ................................................................................................. 26

5.4.5 Manual stand by ................................................................................................ 26

6Errors and Countermeasures ........................................................................................... 27

7Care and maintenance...................................................................................................... 29

7.1 Intervals..................................................................................................................... 29

7.2 Replacement of sterile filter...................................................................................... 29

7.3 Modul replacement ................................................................................................... 30

7.4 Replacement of the UV lamp .................................................................................... 31

7.5Replacement of the reverse osmosis module.......................................................... 32

7.6 P&I scheme................................................................................................................ 33

7.7 Consumables............................................................................................................. 34

7.8 System update .......................................................................................................... 34

8Users FAQ’s ...................................................................................................................... 35

General

General1

About this manual1.1

This manual describes how to use the equipment safely and correctly. When operating this

equipment, it is essential that the user adhere to the safety and operating instructions

included in the manual. Local safety and general safety regulations should also be followed

when using this equipment.

Before using the equipment, the user must read the entire manual, particularly the section

on safety and the relevant safety warnings. The user must fully understand the instructions

before operating the equipment.

The user manual is a part of the equipment. It must be kept close to the equipment and be

accessible at all times for all users. Should the equipment be passed on to a third party, the

manual must also be passed on to the third party.

Symbols used in this manual1.2

Issues relevant to safety are characterized in this manual according to the following

symbols. These warnings must be observed in order to operate the equipment safely and

avoid accidents, damage or injury.

Risk of serious or fatal injury:

This symbol alerts the user to potential serious or fatal injuries. Do not operate

the equipment until you have completely understood the instructions and

proceed accordingly.

Risk of electric shock:

This symbol alerts the user to the presence of un-insulated electric power that

has the potential to cause serious or fatal injuries. Do not operate the equipment

until you have completely understood the instructions and proceed accordingly.

All maintenance work must be performed by qualified service personnel.

General

Important note:

This symbol alerts the user to potential sources of malfunctions or damage to

the equipment if operated improperly.

Important reference to the manual:

It can be dangerous to undertake work on those parts of the system, labeled

by this symbol, unless the manual has been read and understood.

Advice:

This symbol alerts the user to advice on efficient and trouble-free operation.

Liability and warranty1.3

The manufacturer of this product has many years of experience and expertise in the field of

water treatment technology. This manual has been written based on current safety code

legislation and state-of-the-art technology.

The user manual must be kept close to the equipment and available at all times for anyone

intending to use the equipment.

The user manual must be read before any work is carried out using the equipment! The

manufacturer does not accept liability for damage or faults that arise due to disregard for

the instructions in the manual.

The text and diagrams depicted in this manual do not necessarily match the equipment you

have received. The diagrams and images are not on a scale of 1:1.

The equipment delivered to you may be slightly different to the equipment described and

depicted here due to special features, additional options or changes in technology. If you

have any questions, please contact the manufacturer.

We reserve the right to make technical changes to the product and further develop it in

order to improve its functionality.

Copyright1.4

This manual must be treated as a confidential document. It is only intended for use by

those operating the equipment.

General

All contents of this manual –text, diagrams, images etc. –are protected by copyright law

and industrial property rights. Anyone found violating these rights will be prosecuted.

The manual may not be passed on to third parties, copied –either in part or whole –or

used for any other purpose without the express and written consent of the manufacturers.

Anyone found violating these copyright laws must pay compensation. The manufacturer

may also prosecute.

We reserve the right to exercise all industrial protection rights.

Spare parts1.5

Only use original spare parts supplied by the manufacturer.

The wrong or faulty spare parts can lead to damage, malfunction or a complete

breakdown of the equipment.

All guarantees, warranties, service, damage and liability claims against the manufacturer,

the manufacturer’s representatives and dealers become null and void if unauthorized spare

parts are used in the equipment.

Disposal1.6

If no return or disposal contract has been agreed on, please dispose of the disassembled

components as follows:

Recycle scrap metal parts,

Recycle plastic parts,

Dispose of other components according to the material.

Electrical and electronic scrap and components, lubricants and other process

materials must be treated as hazardous waste and can only be disposed of by

authorized waste disposal facilities.

Safety

Safety2

At the time this equipment was developed and produced, it complied with current state-of-

the-art technology and is accepted as reliable and safe.

The equipment can represent a hazard if it is operated by untrained personnel. Improper

operation or operation not in accordance to the manual may pose a hazard.

The section on safety provides an overview of all the important issues relevant to personal

safety and safe, trouble-free operation of the system.

The other sections of the manual also contain specific safety warnings and warning

symbols that highlight possible hazards. Please comply with the pictograms, signs,

markings and inscriptions on the equipment. These must not be removed and must always

be visible.

Intended use2.1

The equipment is only safe if operated as intended and described by the instructions in this

manual.

Any form of use or operation other than the intended use is improper and

prohibited.

Claims of any kind made against the manufacturer or the manufacturer’s representatives

are null and void if the equipment is not operated as intended.

The operating company is liable for all damages caused by improper use.

The intended use is described in the manual and includes compliance with the operating

conditions.

The equipment may only be operated with the parts supplied.

Contents of this manual2.2

Anyone intending to work with or use the equipment must read and understand the user

manual before operating the equipment. This applies even if the user has already operated

similar equipment or devices of a similar nature or has been trained by the manufacturer.

Safety

Reading and understanding the manual is the only way to protect against potential hazards,

prevent mistakes and operate the equipment safely and efficiently.

We recommend that the operating company obtain written confirmation from each user

that he/she has read and understood the manual.

Changes and modifications to the equipment2.3

In order to avoid hazards and ensure that the equipment operates at its best, do not make

any changes or modifications to the equipment that have not been expressly authorized by

the manufacturer.

Ensure that all pictograms, signs, markings and inscriptions on the equipment are always

visible and never removed. Damaged, missing or illegible pictograms, signs, markings and

inscriptions must be replaced immediately.

User responsibility2.4

The user manual must be kept close to the equipment and available at all times for anyone

intending to use the equipment.

The equipment may only be operated in a technically flawless and safe state. The

equipment must be checked for damage before each start-up.

The instructions in the manual must be followed completely and without restriction!

When operating this equipment, it is essential that the user adhere to the safety and

operating instructions provided. The local accident prevention regulations, general safety

regulations and relevant environmental protection legislation must also be followed.

The operating company and the authorized personnel within that company are responsible

for properly operating the equipment. The operating company must define who is

responsible for installing, operating, servicing and cleaning the equipment.

The operator is obliged to perform an operations manual. Otherwise the warranty expires.

Personal requirements2.5

Only authorized and trained personnel are allowed to operate the equipment. The user must

have been instructed about the potential hazards involved in using the equipment.

Table des matières

Autres manuels MP Système de filtration d'eau

MP Aquinity 2 E Manuel utilisateur

Manuels Système de filtration d'eau populaires d'autres marques

Wisy

Wisy LineAir 100 Manuel utilisateur

Schaffner

Schaffner Ecosine FN3446 Series Manuel d'utilisation

Pentair

Pentair FLECK 4600 SXT Guide de l'utilisateur

H2O International

H2O International H20-500 Manuel utilisateur

Renkforce

Renkforce 2306241 Manuel utilisateur

Neo-Pure

Neo-Pure TL3-A502 Manuel utilisateur

FLTR

FLTR OBF Manuel utilisateur

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuel utilisateur

Applied Membranes

Applied Membranes W-G844EM Manuel utilisateur

BEGA

BEGA 116 Manuel utilisateur

WATA

WATA Standard Manuel utilisateur

Price

Price FFU series Manuel

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuel utilisateur

Brita

Brita SAFF-100 Manuel utilisateur

HEISSNER

HEISSNER FPU24000-00 Manuel utilisateur

BGS technic

BGS technic 1518 Manuel utilisateur

Reverse Osmosis

Reverse Osmosis RF Series Manuel utilisateur

ubbink

ubbink Filtramax Series Manuel utilisateur