Motorola MC4000 Manuel utilisateur

Quick Start

Guide

cellular multisensor

Model MC4000

Packaged with your MultiSensor

Cellular MultiSensor with Antenna,

pre-installed Rechargeable Battery Pack Accessory,

and pre-installed SIM Card

Power Cube

Water/Flood Probe

Para una Guía de Inicio Rápido en español, por favor

vaya a

www.motorolanetwork.com/SENSORir

Let's get started

The Motorola Cellular MultiSensor senses temperature,

humidity, water/flood, light intensity, shaking/acceleration,

presence of AC power, cell signal strength, and backup

battery status. Please see Sensor Details on page 14 for

specifics about these sensors.

Installing the MultiSensor

The Motorola Cellular MultiSensor is easy to install. Here's

what to do:

1Switch on the MultiSensor's backup battery.

The battery's switch is shown below. Use a paper clip, pen,

or similar pointed object to gently move the slider to the 1

position (Battery ON).

Keep the switch in the ON position unless you're not

going to be using the MultiSensor for a long period of time

and you want to save battery power. Note that the

battery will only charge when the switch is in the ON

position.

2Plug the MultiSensor into a power source.

Typically, you plug the MultiSensor into the included USB

power cube, and then plug the USB power cube into an

AC wall outlet that's powered on. If you plan to use the

MultiSensor's water-sensing probe, you'll want to plug the

sensor and cube into a power outlet near the source of a

possible "flood". If you're not using the probe, think about

which sensors you want to use and place the MultiSensor

accordingly.

Here are some other possible sources of power:

a. A computer's USB port. To ensure consistent power

supply, the computer should be configured to be

running all the time. (Note: the heat generated from

the computer may affect the MultiSensor's

temperature and humidity readings.)

b. A suitable USB power bank. A USB power bank is

useful if you want to run the MultiSensor for more

than 2 days without AC power. Care should be

taken in selecting a compatible power bank as many

power banks have auto-shut off features that

cannot be disabled. For compatible power bank

suggestions, please see

www.motorolanetwork.com/PowerBanks

3If you want to monitor for "flood", plug in the water-

sensing probe.

Plug the included water-sensing probe into the micro-USB

port on the MultiSensor as shown. You can put the probe

on the floor, or you can mount it on a wall or post if you

prefer.

The water sensing probe works when the metal probes

both make contact with water. When the water sensor is

on a floor, the metal probes should rest on the floor.

The flood cable length is 5 feet. If you need a longer cable,

you can plug the flood cable into a Micro-USB Extension

Cable, which has a micro-USB male connector on one end

and micro-USB female connector on the other end. These

are inexpensive, and various lengths are available online.

Setting up service using the

MultiSensor app or a Web browser

Now that you have the hardware installed, you can connect

and configure your device using the web browser or the

Motorola MultiSensor app on an iPhone or one of the many

popular Android phones made by Motorola, Samsung, and

many other companies.

Instructions below are for installation using the app for

smartphones, iPads, and other smart devices. If you are going

to use the web browser instead, go to:

https://sensor.motorolanetwork.com/, and substitute clicks

for taps in the instructions below.

If you are adding a MultiSensor to an existing account, skip to

step 3.

1Download the Motorola MultiSensor app for Android or

iPhone through Google Play or the Apple App Store.

Search for Motorola MultiSensor and look for the

Motorola icon below. Follow the instructions on your

smart device to download and install the app. (Or, go to

https://sensor.motorolanetwork.com/in your web

browser.)

2Set up your account.Once it is installed, the app will

appear on your device with the name MultiSensor.

Opening the mobile app, a Sensor App Login Page is

displayed.

•On the bottom right of the page

is a

selection. Select it

then complete the information

requested on the next page.

This information (e-mail and

phone number) will be used as

the default Alert Recipient for

this account but may be edited

later.

•A registration code will be sent

to the e-mail address provided.

This code will need to be

entered to finish setting up the

account.

Note: once the account is set up you will need to login

using the provided e-mail address and password to

continue with further setup.

3Add your MultiSensor. Tap the Configuration tab at the

bottom of the screen. Tap Sensor and then the blue +to

add your sensor. You will see a page with fields to be

complete.

•Sensor Name – use

Upper/Lower case letters and

numbers only. No special

characters. For example,

Basement or Beach House.

•

Sensor ID (IMEI Number)

–

type the unique IMEI number

that’s printed on a label on your

MultiSensor. You may wish to

write this down or take a picture

of it.

•

Upload button

– you can

optionally upload a photo to

help identify your MultiSensor,

and the photo will be displayed

on the Dashboard page. If

Upload is not selected, then a

sensor picture will be used.

Note: This default picture is not

displayed on this page but will

appear on the Dashboard once

the sensor is added.

•

Time Zone

– a selection box to

select the time zone where the

sensor is used.

Once all fields are complete, the ADD button at the

bottom will become selectable to finish adding the sensor

to this account.

Note: If using the browser URL and not the mobile app,

then Configure is at the top of the page. When selected,

the next page on the left will display Add a New Sensor

with the same fields. The default picture is displayed. At

the bottom of the page, click Save.

4Finally, you will need to set up and activate a

subscription for service for your MultiSensor. The first

month of service is free. Subsequent months are $5 per

month per sensor. When you add an additional

MultiSensor to an existing account, the service begins

charging on the next billing cycle after it is installed.

•Select

Account

. Select

Wallet

and follow the

prompts on the

Manage

Wallet

page to

Add a new

payment method

and to

enter billing information.

Then tap

Add your Card

The page

Select a billing

address

will display. If the

address is already populated,

select it and select

Use this

Address

. Otherwise, tap

Add

a new Address

. Complete

the fields and select

Add

•Once the payment

information is setup, return

to the Account page and

select

Payments

which

displays the

Payments

page.

Tap

Activate

for the desired

sensor displayed and follow

the prompts on the

Billing

Plan

page to set up your

subscription. After selecting

Place Your Order

, a Receipt

screen will display, and an

email will be sent to the

Account Holder confirming

your subscription. Your

subscription should be

activated!

Using your MultiSensor

Reading the MultiSensor Dashboard. The Dashboard

displays information reported by all the sensors, and signal,

power and battery status. The Updated field tells you the last

report time. Normally the device reports every 20 minutes. If

you tap the device icon at the top of the dashboard, the

dashboard will show you data from the most recent report. If

you tap the Refresh button, the device will send a fresh report

with up-to-the-minute data. If after installation you see a

grayed-out dashboard, unplug your sensor, switch the battery

off, and turn it back on. Then plug the sensor back in.

Configure your MultiSensor for the way you want to use it.

Tap the Dashboard tab at the bottom of the screen on your

mobile app (the browser on your computer displays

Dashboard on the top left). After a short delay, you should see

the Dashboard screen with information displayed from your

MultiSensor.

•Tap any Dashboard sensor icon

to enable and configure alerts,

and to view history. If you'd

like, you can set alerts for any

sensor. For instance, you may

want to be alerted if there's

water on your floor or if the

temperature drops below 47

degrees, or if there's a power

loss.

Follow the on-screen

instructions for details and

read the next section for

additional assistance.

Table des matières

Autres manuels Motorola Accessoires

Motorola

Motorola LM100 - SOUTHERNLINC Manuel utilisateur

Motorola

Motorola AirDefense Model 510 Manuel utilisateur

Motorola

Motorola hmsm4050 Manuel utilisateur

Motorola

Motorola Horizonmacro outdoor Manuel utilisateur

Motorola

Motorola MTR2000 Manuel utilisateur

Motorola

Motorola Focus TAG Manuel utilisateur

Motorola

Motorola RDU4160d Manuel utilisateur

Motorola

Motorola C370 Series Manuel utilisateur

Motorola

Motorola ENLN4103 Manuel utilisateur

Motorola

Motorola MTS LiTE Manuel utilisateur

Motorola

Motorola P1500 Manuel utilisateur

Motorola

Motorola 8900 - Blackberry Curve Cell Phone OEM Car... Mode d’emploi

Motorola

Motorola hmsm4050 Manuel utilisateur

Motorola

Motorola sd4561 Manuel du propriétaire

Motorola

Motorola MTR2000 T5544 Manuel utilisateur

Motorola

Motorola sd4581 Manuel du propriétaire

Motorola

Motorola ASTRO 25 GTR 8000 Guide de l'utilisateur

Motorola

Motorola Motoactv Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur