Morningstar SunSaver Series Mode d’emploi

SunSaver

Field Testing Procedures

Abstract:

The following test procedure was developed for use in ﬁeld conditions, where no external

power sources are available.

Technical Documentation

page 2 of 5

Note: Due to the fabrication process of the SunSaver controller, the exact damaged component may

not be evident. It may only be possible to determine if the unit is functioning properly. How-

ever, other factors may be apparent the will assist the technician in determining the cause of the

failure.

Recommended Tools:

• Digital multi-meter (frequency and duty cycle measurement are helpful)

• Phillips Screwdriver

• Flat Bladed Screwdriver

• 12V/2A load (type 1156 automotive lamp with socket works well)

• Short length(6 in) of 12AWG solid wire.

Caution:

The following outlined procedures assume a basic working knowledge of electrical circuits. Ex-

ercise the necessary precautions when dealing with live electrical circuits present in solar energy

systems

Testing Procedure

Step 1: No PowerApplied to SunSaver

A) With no power applied to the SunSaver, check for short circuits to ground between the following terminals:

i) PV (+) and PV (-) terminals

ii) Battery (+) and Battery (-) terminals

iii) Load (+) and Load (-) terminals

Battery Load

+-+-

PV (+) and PV (-)

Terminals

iii

Load (+) and Load (-)

Terminals

Batt (+) and Batt (-)

Terminals

page 3 of 5

(step 1 cont.)

B) Check the LVD FET (if controller is equipped with LVD) by measuring a diode drop between Battery (+) and Load

(+) terminals. If no diode drop is present or if an open circuit is measured, the LVD FET is damaged. If no diode drop is

present (short circuit), the unit will still (most likely) regulate the battry voltage properly, however the controller will no

longer have LVD capability.

C) Check for continuity between the ground connections on the terminal strip (PV (-), Battery (-), and Load (-).

D) Remove the four screws from the face plate. Bend a small hook in one end of a 12AWG solid wire. Insert the hook

into one of the screw holes and pull off the face plate. The face place may be stuck to the internal potting and may make

a cracking sound when removed. This is normal and will not demage the internal circuitry. Inspect for burns, damaged

traces, etc.

Step 2: Battery Connected to Battery Terminals Only

Note: The green “charging” LED should be off.

A ) Measure the voltage at the battery terminals.

B) Measure the voltage at the load terminals. The voltage should be the same(+/- 200mV) as the battery voltage. If load

voltage is signiﬁcantly lower than battery voltage, LVD FET’s or the power traces inside the SunSaver are damaged.

C) Measure the voltage at the Solar (PV) terminals. The voltage should be less than 2.5 Vdc. If green LED is on, or bat-

tery voltage is measured at Solar terminals, the input FET’s are damaged and the unit will not regulate battery voltage

properly.

Step 3: PV and Battery PowerApplied to the Controller:

Note 1: The green “charging” LED should be lit

A)The voltage across the PV terminals should be the same as the

voltage across the Battery terminals if the battery is not fully

charged.

B)If the batteries are charged, there will be a voltage difference

between the PV (+) and Battery (+). If your multi-meter has a

frequency measuring option, a 300Hz AC signal should be

measured between the PV (+) and Battery (+). The duty cycle

of this signal can be used to give a rough indication of the battery

state of charge. A lower duty cycle indicates a battery with a

higher state of charge. Regulated

Power Supply

+ -

Battery Load

+-+-

Battery

page 4 of 5

Step 4: PV, Battery, and Small (2A) Load Connected to Controller

Note 1: A standard automotive brake lamp (type 1156) works well for this test.

A) with the lamp turned On, measure the Load Voltage. It should

be within 20-30 mV of the battery voltage. If the Load voltage is

more than 0.25V lower than the Battery voltage, the LVD FET’s

are damaged. Battery Load

+-+-

Battery

2A Load

Array

Step 5: SunSaver Installed in the Power System.

A) Check the correct operation of the SunSaver based on the above tests.

B) Check the condition of any fuses that might be in the power path.

C) Verify the system wiring is correct and intact.

D) Check all connections and terminals for good electrical contact.

page 5 of 5SS.APP.Field_Test.01.EN

page 5 of 5 Revision Date: 09/29/11

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Morningstar Contrôleurs

Morningstar

Morningstar SunSaver Duo SSD-25RM Manuel utilisateur

Morningstar

Morningstar SUNSAVER MPPT Series Manuel utilisateur

Morningstar

Morningstar ProStar MPPT TRAKSTAR PS-MPPT-15 Manuel utilisateur

Morningstar

Morningstar SUNSAVER MPPT SS-MPPT-15L Manuel utilisateur

Morningstar

Morningstar TriStar TS-MPPT-30 Manuel utilisateur

Morningstar

Morningstar SUNSAVER MPPT SS-MPPT-15L Manuel utilisateur

Morningstar

Morningstar ProStar-15 Manuel utilisateur

Morningstar

Morningstar REAKSTAR GenStar GS-MPPT-60M-200V Manuel utilisateur

Morningstar

Morningstar PROSTAR-12 Manuel utilisateur

Morningstar

Morningstar TriStar TS-45 Manuel utilisateur

Morningstar

Morningstar ProStar PS-15 Manuel utilisateur

Morningstar

Morningstar EcoBoost MPPT EB-MPPT-20 Manuel utilisateur

Morningstar

Morningstar TrakStar TriStar TS-MPPT-60M Manuel utilisateur

Morningstar

Morningstar Sunlight SL-10 Manuel utilisateur

Morningstar

Morningstar TRISTAR TS-MPPT-60-600V-48-DB Manuel utilisateur

Morningstar

Morningstar ProStar PS-30M-PG Manuel utilisateur

Morningstar

Morningstar MC6 MkII Manuel utilisateur

Morningstar

Morningstar SunSaver SS-6 Manuel utilisateur

Morningstar

Morningstar SunSaver MPPT Meter Map Manuel utilisateur

Morningstar

Morningstar SunSaver-10 Manuel utilisateur

Morningstar

Morningstar ProStar MPPT Series Manuel utilisateur

Morningstar

Morningstar ProStar PS-15M-48V Manuel utilisateur

Morningstar

Morningstar SHS-6 Manuel utilisateur

Morningstar

Morningstar TriStar Professional TS-60M Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur