Mooer SynthDrum Manuel utilisateur
Electronic Hand Drum
Owner’s Manual
01
Contents
...........................................................02
.......................................................03
..................................................03
..............................................................05
............................................................05
...............................................................05
.................................................................06
............................................................06
............................................................07
................................................07
..................................................08
..................................................................08
...................................................08
.......................................09
..........................................10
.........................................................11
...................................................12
...............................................................13
.........................................................13
..........................................................18
..........................................20
Precautions
Main Features
Panel Instruction
Operation
Playing
Drum Head Replacing
Specification
Troubleshooting
Appendix
PATCH
LOOP
EFX
SENSE
CURVE
Saving Patches
Factory Reset
Basic Playing
Pressure Pad Effects
Patch List
Loop List
Velocity Curve List
02
Precautions
*PLEASEREADCAREFULLYBEFOREPROCEEDING*
Power Supply
Please connect the designated AC adapter to an AC outlet of the correct
voltage.
Be sure to use only the AC adapter supplied with the unit.
Unplug the AC power adapter when not using or during electrical storms.
Connections
Always turn off the power of this and all other equipment before
connecting or disconnecting, this will help prevent malfunction and / or
damage to other devices. Also make sure to disconnect all connection
cables and the power cord before moving this unit.
Location
To avoid deformation, discoloration, or other serious damage, do not
expose this unit to the following conditions:
Direct sunlight
Heat sources
Magnetic fields
Extreme temperature or humidity
Excessive dusty or dirty location
High humidity or moisture
Strong vibration or shock
Interference with other electrical devices
Radios and televisions placed nearby may experience reception
interference. Operate this unit at a suitable distance from radios and
televisions.
Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.
Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax,
solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Handling
Do not apply excessive force to the switches or controls.
Do not let paper, metallic, or other objects into this unit.
Take care not to drop the unit, and do not subject it to shock or excessive
pressure.
LOOP PLAY PATCH EFX
VOLUME
CURVE
DIAL / ENTER
Hold For Saving Press
OUTPUT (HP)
DC 9V
AUX IN POWER
On
- +
Off
SENSE
03
Main Features
Aluminum alloy drum frame
Hi-Tech composite materials 8″ drum head
200 preset/user sound
100 various style/tempo music loops
(50 drum loops + 50 melody loops)
5 global effect types
5 pressure pad effects
Sensitivity adjusting
9 kinds of velocity curve
1/4″ phones jack & 1/8″ AUX in jack
DC 9V adapter (500 mA, center positive) power supply
1
2
11
4
1210
6789
14 13
5
3
Panel Instruction
04
01
02
03
04
05
Drum Head: 8″drum head, for playing drum head sound.
Drum Rim: For playing drum rim sound.
Drum Rim Notch: For playing drum rim scratching sound.
VOLUME Knob: Rotate this knob to adjust output volume.
DIAL/ENTER Encoder with Button: Dial the knob to select
Patch/Loop, adjust loop level and Effects parameters. Press the
button to ensure selecting/storing, switch loop parameters and effect
types. Hold the button to enter store function.
06
07
08
09
10
11
12
13
14
LOOP Button: Press this button to enter Loop status, when in Loop
status, press this button to switch between Loop Selecting and Loop
Volume Adjusting function.
PLAY Button: Press this button to play or stop loop.
SENSE composite Button: Press [LOOP] and [PLAY] button
simultaneity to enter Sensitivity editing.
PATCH Button: Press this button to enter Patch status.
EFX Button: Press this button to enter Effects status, when in
Effects status, press this button to change effect types.
CURVE composite Button: Press [PATCH] and [EFX] button
simultaneity to enter Velocity Curve editing.
Display: Instruct the operation information of Synth Drum.
OUTPUT (PHONES) Jack: 1/4″stereo audio jack, output the
sound.
AUX IN Jack: 1/8″stereo audio jack, for connecting external music
players (for example: CD Player, MP3 Player, and so on).
DC 9V Power Jack: For power supply, use a 9-volt DC regulated
AC adapter, 500 mA (plug polarity is negative on the barrel and
positive in the center).
POWER Switch: To switch power on/off of Synth Drum.
05
Operation
PATCH
LOOP
01
02
03
01
02
03
04
Entering Patch Status
At any time of using Synth Drum, press [PATCH] button to enter
Patch status, the middle dot of display will be lit up to indicate the
current status (Patch).
Selecting Patches
When in Patch Status, rotate [DIAL/ENTER] knob to select patches,
the patch’s number will be flashing, but the sound will not be
changed yet.
Confirm Patch Selecting
When the number of patch is flashing, press [DIAL/ENTER] button
to confirm selecting, the number will stop flashing, and the sound will
be changed to the current patch.
Entering Loop Status
At any time of using Synth Drum, press [LOOP] button to enter Loop
status, the left dot of display will be lit up to indicate the current
status (Loop).
Selecting Loops
When in Loop Status, rotate [DIAL/ENTER] knob to select loops, the
loop’s number will be flashing, but the music will not be changed yet.
Confirm Loop Selecting
When the number of loop is flashing, press [DIAL/ENTER] button to
confirm selecting, the number will stop flashing, and the music will
be changed to fit the corresponding loop.
Playing and Stop Playing
At any time of using Synth Drum, press [PLAY] button to play the
music, when playing, press [PLAY] button will stop the music.
Note: When switching Patch or Loop, or pressing [PLAY] buon to start loop playing,
the sound will phonate aer few seconds.
06
EFX
SENSE
01
02
03
04
Entering EFX Status
At any time of using Synth Drum, press [EFX] button to enter Effects
status, the right dot of display will be lit up to indicate the current
status (Effects).
Changing Effect Types
When in Effects Status, press [DIAL/ENTER] or [EFX] button to
change effect’s type, there are 5 kinds of effect to choose: Chorus,
Flanger, Phaser, Delay, and Reverb.
Adjusting Effect Parameters
When in Effects Status, rotate [DIAL/ENTER] knob to adjust effect’s
parameters, the range of each effect is 0~9.
Note: Only one effect can be selected at a time, When parameter=0, the effect will be off.
Note: The SENSE contains both drum head and drum rim’s sensitivity value, when
choosing one value, the head and rim’s sensitivity will be changed together.
EFX list
Type Display Parameter Range Parameter Meaning
Chorus Chorus Rate
Flanger Flanger Rate
Phaser Phaser Rate
Delay Delay Time
Reverb Reverb Time
At any time of using Synth Drum, press [LOOP] and [PLAY] button
simultaneity to enter sensitivity editing.
When in SENSE editing status, rotate [DIAL/ENTER] knob to change
sensitivity value, the range is 1~9, display will show “ ~ ”, the
default value is .
~
~
~
~
~
07
CURVE
Saving Patches
Note: The CURVE contains both drum head and drum rim’s velocity curves, when
choosing one curve, the head and rim’s velocity curves will be changed together.
(refer to Appendix for detail).
Note: Aer saving, the patches will be changed to user’s seing even though next
power on.
Note: Do factory reset will initialize the patches to preset.
At any time of using Synth Drum, press [PATCH] and [EFX] button
simultaneity to enter velocity curve editing.
When in CURVE editing status, rotate [DIAL/ENTER] knob to change
velocity curve, there are 9 curves to be chosen, display will show
“ ~ ”, the default value is .
Synth Drum’s 200 Patches can be edited and saved by users, the
modifiable items include SENSE, CURVE and Effects’ parameters. User
can change the parameters of them and save them to the patches.
At any time of using Synth Drum, hold [DIAL/ENTER] button for 3
seconds to do saving operation, then the patch’s number, the middle
dot, and the right dot on the display will begin to flash together, at that
time, press [DIAL/ENTER] button again to confirm, the patch’s number
on the display will stop flashing.
When saving (the patch’s number, the middle dot, and the right dot flash
together), press other buttons (except [DIAL/ENTER]) to quit saving and
enter the corresponding status.
08
Factory Reset
Basic Playing
Playing
Note: If you want to quit Factory Reset halfway, press another buon except
[DIAL/ENTER], then the Factory Reset will be canceled.
Factory Reset function will initialize all setting of Synth Drum. All the
patches will be erased and overwritten by the presets, the SENSE and
CURVE’s setting will be set to default as well.
To do the factory reset, conform to the following instructions:
Hold down [DIAL/ENTER] button and then power on, will appear
on the display and last flashing.
At that time, press [DIAL/ENTER] button to confirm, will be
flashing in a faster speed for 2 seconds, then turn to display at a
steady status for 3 second, then back to the normal state, the factory
reset operation have been done.
Use drum sticks
Use rods
Use your hands
09
Pressure Pad Effects
Note: Pressure pad effects are real-time control, when the pressure is released, the effect
will be off.
Synth Drum has a pressure sensor under the drum head. To create
pressure pad effects on your playing, put your palm on the drum head
and exert strength, then play the head or rim (or play the drum firstly,
then put the palm on the head and press), you will get the special sound
of different type effects in different patches. More stress, more effects.
There are 5 kinds of pressure pad effects fixed up in each patch: Pitch
Up, Pitch Down, Vibrato, AEG, Volume, one of them has been fixed up
in each patch, the setting can not be modified by users.
Pressure Pad Effects List
Type Explanation More Stress
Pitch Up Pitch shift upwards Higher Pitch
Pitch Down Pitch shift downwards Lower pitch
Vibrato Inflect the pitch periodically More Depth
AEG Decrease sustain and decay time Shorter Time
Volume Decrease patch volume Lower Volume
Please read Patch List on Appendix for particular assigning information.
Wrench
Tighten or loosen
There is an adjustable screw on the
bottom centre for adjusting the
sensitivity of pressure pad.
Use the accessary wrench to
tighten the screw for lower
sensitivity or loosen it for higher
sensitivity.
*Patent pending
Table des matières
Autres manuels Mooer Matériel de musique
