Molex 63811-5600 Manuel utilisateur

Hand Crimp Tool for Contact Pin Crimp Terminals

Doc No. ATS-638115600 Release Date: 01-18-07 UNCONTROLLED COPY Page 1 of 6

Revision: D Revision Date: 01-18-07

CONDUCTOR

BRUSH

STRIP LENGTH

SEAM

BEND UP

TWISTING

ROLLING

BEND

DOWN

CONDUCTOR

CRIMP

CUT-OFF

TAB

BELL MOUTH

WIRE

HAND CRIMP TOOL

SPECIFICATION SHEET

Order No. 63811-5600

FEATURES



A full cycle ratcheting hand tool ensures complete crimps



Ergonomic soft grip handles for comfortable crimping



A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position



This tool is IPC/WHMA-A-620 Class 2 (except as noted) and RoHS compliant

SCOPE

Products: Contact Pin Crimp Terminals, 14-18 AWG.

Terminal Order No. Wire Size Insulation Diameter Strip Length

Terminal Series No.

Available in Reel form only AWG mm² mm in mm in

14 2.09

ÆÆ

3.05-3.81 .120-.150

16 1.33 2.41-3.05 .095-.120

84590

84590-0022

84590-0023

84590-0028

84590-0029

84590-0037

84590-0038 18 0.82 1.91-2.41 .075-.095

4.45 .175

Follow the Cut-Off Tab specifications on Applicator specification sheets.

ÆÆ

IPC/WHMA-A-620 Class 2 only 3.05-3.40mm (.120-.134”)

DEFINITION OF TERMS

TYPE 4C

Hand Crimp Tool for Contact Pin Crimp Terminals

Doc No. ATS-638115600 Release Date: 01-18-07 UNCONTROLLED COPY Page 2 of 6

Revision: D Revision Date: 01-18-07

CRIMP SPECIFICATION

Bell Mouth Bend up Bend down Twist Roll Conductor Brush

Terminal Series No. mm In. Degree Degree mm In.

84590 0.13-0.37 .005-.015 5 5 5 10 0.75-1.25 .030-.050

Seam

Seam shall not be open and no wire allowed out of the crimping area

CONDITIONS:

After crimping, the conductor profiles should measure the following (See notes on page 4).

Conductor

Wire Size Crimp Height (Ref) Crimp Width (Ref)

Pull Force

Minimum Profile

Terminal Series No.

AWG mm2mm in. mm in. N Lb. 14 16 18

14 2.09 1.73-1.81 .068-.071 2.55 .100 111.2 25.0 X

16 1.33 1.48-1.56 .058-.061 2.55 .100 111.2 25.0 X

84590

18 0.82 1.36-1.44 .054-.057 2.55 .100 111.2 25.0 X

OPERATION

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage can occur to the tool

or die.

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles, and

the hand tool will spring open.

Crimping Terminals

1. Select the desired terminal listed in the preceding charts.

2. Swing the terminal locator away from the crimp tool shown in Figure 1. Some terminals with large insulation grips may interfere

with the crimp tooling when swinging the locator into position. The terminal must then be loaded into the locator in the

closed/crimp position. See Figure 2.

SWING OPEN

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

LOCATOR

TERMINAL IN PLACE

Figure 1

Hand Crimp Tool for Contact Pin Crimp Terminals

Doc No. ATS-638115600 Release Date: 01-18-07 UNCONTROLLED COPY Page 3 of 6

Revision: D Revision Date: 01-18-07

HANDLE

OPEN

LOCATOR

CLOSED

Figure 2

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

Figure 3

WIRE IN TERMINAL

JAWS

PARTIALLY

CLOSED

WIRE AGAINST

WIRE STOP

3. Press down on the wire stop on the locator as shown in Figure1. Insert the proper terminal into the proper nest opening. Make

sure when choosing the nest opening, it will correspond with the 14, 16 or 18 profile on the hand tool.

4. Return the locator to its original position.

5. Insert the proper wire over the terminal. Gently touch the wire stop with the end of the wire. See Figure 3 and 4.

6. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed. Release handles to

open the jaws.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

7. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on the wire. The

terminal locator can be in either position.

8. Visually inspect the crimped terminal for proper crimp location.

Note:

A crimp height chart is provided with this manual as Reference

Only. Due to the wide range of wires, strands, insulation

diameters, and durometers, actual crimp height measurements

may very slightly. An occasional, destructive, pull force test

should be preformed to check hand tool crimp. Pull Force value

must exceed the minimum pull force specifications listed.

Figure 4

WIRE

INSULATION

PUNCH

CONDUCTOR ANVIL

LOCATOR

INSULATION

ANVIL

WIRES AGAINST

LOCATOR STOP

CONDUCTOR

PUNCH

TERMINAL

Hand Crimp Tool for Contact Pin Crimp Terminals

Doc No. ATS-638115600 Release Date: 01-18-07 UNCONTROLLED COPY Page 4 of 6

Revision: D Revision Date: 01-18-07

Locator Replacement

See the parts list on the last page of this document for the proper locator order number.

Follow the steps below to replace the locator.

1. Open the crimp hand tool.

2. Swing the existing locator open and away from the hand tool.

3. Firmly press down on the brass pivot shaft with your thumb, while pulling the

locator up. Slip the locator off the top of the brass pivot shaft. See Figure 5.

4. Replace it with the proper locator by putting over the brass pivot shaft and

snapping it into place.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins, pivot points, and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil

excessively. The tool was engineered for durability but like any equipment it needs cleaning and lubrication for a maximum

service life of trouble free crimping. Use light oil (30 weight automotive oil), at all the oil points, every 5,000 crimps or 3

months. This will significantly enhance the tool life. See Figure 6.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil

transferred from the crimping area onto certain terminations may

affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects

from becoming lodged in the crimping dies, and store the tool in a

clean, dry area.

Miscrimps or Jams (See Figure 7)

Should this tool ever become stuck or jammed in a partially closed

position, Do Not force the handles open or closed. The tool will open

easily by rotating the small slotted screw marked with an arrow. See

Figure 7.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long

life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will

repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This

tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty.

SWING

LOCATOR

OPEN

PRESS DOWN

ON THE BRASS

PIVOT SHAFT

LIFT UP ON

THE LOCATOR

Figure 5

LUBRICATION POINTS

(BOTH SIDES) LIGHT OIL

(EVERY 3 MONTHS OR

5,000 CRIMPS)

Figure 6

Hand Crimp Tool for Contact Pin Crimp Terminals

Doc No. ATS-638115600 Release Date: 01-18-07 UNCONTROLLED COPY Page 5 of 6

Revision: D Revision Date: 01-18-07

Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive

use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

CAUTION: Repetitive use of this tool should be avoided.

Certification

Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for customers to re-certify

hand tools.

This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped 12.7mm (1/2”) long, so

there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than 25mm (1.00”) per minute. See the

Molex web site for the Quality Crimp Handbook for more information on pull testing.

When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced.

This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.

Hand Crimp Tool for Contact Pin Crimp Terminals

Doc No. ATS-638115600 Release Date: 01-18-07 UNCONTROLLED COPY Page 6 of 6

Revision: D Revision Date: 01-18-07

RATCHET

RELEASE LEVER

Figure 4

M4 X 8mm

LONG BHCS

PARTS LIST

Item Number Order Number Description Quantity

1 63811-5573 Locator Base 1

2 63811-5575 LocatorAssembly 1

Americas Headquarters

-JTMF*MMJOPJT64"

.0-&9

BNFSJOGP!NPMFYDPN

Far East North Headquarters

:BNBUP,BOBHBXB+BQBO



GFOJOGP!NPMFYDPN

Far East South Headquarters

+VSPOH4JOHBQPSF



GFTJOGP!NPMFYDPN

European Headquarters

.VOJDI(FSNBOZ



FVSJOGP!NPMFYDPN

Corporate Headquarters

8FMMJOHUPO$U

-JTMF*-64"



'BY

Visit our Web site at http://www.molex.com

Autres manuels pour 63811-5600

Table des matières

Autres manuels molex Outils de sertissage

molex

molex AT FIFG Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex AT 1610 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 63811-5300 Manuel utilisateur

molex

molex 63827-0470 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 63819-1500 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 213309-1300 Manuel utilisateur

molex

molex HCS-125 Series Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 64001-2800 Manuel utilisateur

molex

molex 63823-4100 Manuel utilisateur

molex

molex CR5907 Manuel utilisateur

molex

molex 78172 Series Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex AT 1992 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex 63827-6070 Manuel utilisateur

molex

molex 63816-0200 Manuel utilisateur

molex

molex 64001-7300 Manuel utilisateur

molex

molex 207129 Series Manuel utilisateur

molex

molex AT 2080 Guide de l'utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur

molex 63811-5600 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques