molex 63811-5300 Manuel utilisateur
Hand Crimp Tool for MX150LTerminals
Doc No: ATS-638115300 Release Date: 02-28-06 UNCONTROLLED COPY Page 1 of5
Revision: B Revision Date:10-15-07
CONDUCTOR
BRUSH
STRIP LENGTH
SEAM
CONDUCTOR
CRIMP
CUT-OFF
TAB
BELL MOUTH BEND UP
TWISTING
ROLLING
BEND
DOWN
WIRE
WIRE
ANGLE
HAND CRIMP TOOL
SPECIFICATION SHEET
Order No. 63811-5300
FEATURES
%
A full cycle ratcheting hand tool ensures complete crimps
%
Ergonomically designed softhandles
%
Precisely designed crimping profiles with simple contact positioning
%
Easy handling due to outstanding force ratio
SCOPE
Products:MX150L10-12 AWG
Terminal Order No. Wire Size Insulation Diameter Strip Length
Terminal Series No. Loose Piece
Æ
Reel AWG mm² mm In. mm In.
19431 19431-0016 19431-0001 10-12 5.26-3.31 3.90-4.85 .153-.191 5.50-6.20 .217-.244
19434 19434-0003 19434-0001 10-12 5.26-3.31 3.90-4.85 .153-.191 5.50-6.20 .217-.244
Æ
Customer to cut off terminal from reel: 0.50mm (.020”) maximum Cut-off Tab.
DEFINITION OF TERMS
TYPE 4C
Hand Crimp Tool for MX150LTerminals
Doc No: ATS-638115300 Release Date: 02-28-06 UNCONTROLLED COPY Page 2 of5
Revision: B Revision Date:10-15-07
HANDLE
OPEN
LOCK IN
UP RIGHT
POSITION
LOCATOR
CLOSED
Figure 1
TERMINAL
PUSH HERE TO
OPEN WIRE STOP Figure 2
WIRE IN TERMINAL
JAWS
PARTIALLY
CLOSED
WIRE AGAINST
WIRE STOP
CRIMP SPECIFICATION
Bell Mouth Bend up Bend down Twist Roll Conductor Brush WireAngle
Terminal Series No. mm In. Degree Degree mm In. Degree
19431 0.25-1.25 .010-.049 2 3 4 8 0.10-0.50 .004-.020
5°Max
19434 0.25-1.25 .010-.049 2 3 4 8 0.10-0.50 .004-.020
5°Max
Seam: Seam shall not be open and no wire allowed out of the crimping area.
CONDITIONS:
After crimping,the conductor profiles should measure the following (See notes on page 4).
Conductor Insulation
WireSize Crimp Height (Ref) Crimp Width (Ref) Crimp Height (Ref) Crimp Width (Ref) Pull Force
Minimum
Terminal
SeriesNo. AWG mm2mm In. mm In. mm In. mm In. N Lb.
10 5.26 2.45-2.55 .096-.100 3.70-3.90 .146-.154 5.00 Max .197 Max 5.10-5.30 .201-.209 356.0 80.0
19431 12 3.31 2.05-2.15 .081-.085 3.70-3.90 .146-.154 4.50 Max .177 Max 5.00-5.20 .197-.205 311.5 70.0
10 5.26 2.45-2.55 .096-.100 3.70-3.90 .146-.154 5.00 Max .197 Max 5.10-5.30 .201-.209 356.0 80.0
19434 12 3.31 2.05-2.15 .081-.085 3.70-3.90 .146-.154 4.50 Max .177 Max 5.00-5.20 .197-.205 311.5 70.0
OPERATION
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects - damage can
occur to the tool or die.
Open the tool by squeezing the handles together, at the end ofthe closing stroke, the ratchet mechanism will
release the handles, and the hand tool will spring open.
Crimping Terminals
Swing the terminallocator against the crimp tool and turn the lock up to lock the locator. Terminals can be loaded
easily while the locator is against the crimp tooland locked. The spring-loaded locator needs to be in the up
position for terminals to load easily.
Hand Crimp Tool for MX150LTerminals
Doc No: ATS-638115300 Release Date: 02-28-06 UNCONTROLLED COPY Page 3 of5
Revision: B Revision Date:10-15-07
1. To raise the wire stop,press the tab on the wire stop as shown in Figure 1. Insert the proper terminal into the
nest opening and release the wire stop to lower it.
2. Insert the proper pre-striped wire over the terminal. Gently touch the wire stop with the end of the wire. See
Figure 2 and 3.
3. Compress the terminal by squeezing the tool handles untilthe ratchet mechanismcycle has been completed.
Release handles to open the jaws.
Note: The tamper proof ratchetaction will not release the tool until it has been fully closed.
4. Remove the crimp terminal from the terminal
locator by pressing the tab on the wire stop and
gently pulling on the wire.
5. Visually inspect the crimped terminal for proper
crimp location and crimp height.
Maintenance
Itis recommended that each operator ofthe tool be
made aware of,and responsible for, the following
maintenance steps:
1. Remove dust, moisture, and other contaminants
with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials thatcould
damage the tool.
3. Make certain all pins;pivot points and bearing surfaces are protected with a thin coat of high quality
machine oil. Do notoil excessively.
4. When tool is not in use,keep the handles closed to preventobjects frombecoming lodged in the crimping
dies, and store the tool in a clean, dry area.
Miscrimps or Jams (See Figure 4)
Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or
closed. The tool will open easily by rotating the small slotted screw marked with an arrow. See Figure 4.
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we would exchange the tool free of charge. This will not be applicable to
altered,misused, or damaged tools. This tool is designed for hand use only. Any clamping,fixturing, or use of
handle extensions voids this warranty.
Hand held crimping tools are intended for low volume,prototyping, or repair requirements only.
CAUTION: Repetitive use of this tool should be avoided.
LOCATOR ANVIL
TERMINAL
WIRE
PUNCH
WIRE AGAINST STOP
Figure 3
WIRE STOP
Hand Crimp Tool for MX150LTerminals
Doc No: ATS-638115300 Release Date: 02-28-06 UNCONTROLLED COPY Page 4 of5
Revision: B Revision Date:10-15-07
Notes:
1. This tool should only be used for the terminals and wire gauges specified on this sheet.
2. This tool is not adjustable. Variations in tools,terminals, wire stranding and insulation types may affectcrimp
height.A crimp height chart is provided with this manual as Reference Only.
3. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts
available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.
4. An occasional destructive pull force test should be performed to check hand tool crimp.Pullforce should be
used as the finalcriteria for an acceptable crimp.Pull force values Must exceed the Minimumpull force
specifications listed on pages 2 and 3. Refer to Molex Quality Crimping Handbook 63800-0029 for additional
information on crimping and crimp testing.
5. Molex does not certify crimp handtools.
6. This tool is very difficult todisassemble and reassemble. Customer repair is notrecommended.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and
tooling.
Hand Crimp Tool for MX150LTerminals
Doc No: ATS-638115300 Release Date: 02-28-06 UNCONTROLLED COPY Page 5 of5
Revision: B Revision Date:10-15-07
PARTS LIST
Item Number Order Number Description Quantity
1 63811-4773 Locator Basewith Lock 1
2 63811-5375 Locator 1
Americas Headquarters
Lisle,Illinois60532U.S.A.
1-800-78MOLEX
amerinfo@molex.com
Far East North Headquarters
Yamato, Kanagawa, Japan
81-462-65-2324
feninfo@molex.com
Far East South Headquarters
Jurong, Singapore
65-6-268-6868
fesinfo@molex.com
EuropeanHeadquarters
Munich, Germany
49-89-413092-0
eurinfo@molex.com
CorporateHeadquarters
2222 Wellington Ct.
Lisle, IL 60532 U.S.A.
630-969-4550
Fax: 630-969-1352
Visit our Web site at http://www.molex.com
Figure 4
RATCHET
RELEASE SCREW
1
M4 X 8mm
LONG BHCS
2
Table des matières
Autres manuels molex Outils de sertissage
molex
molex 69008-1100 Manuel utilisateur
molex
molex 207129 Series Manuel utilisateur
molex
molex 98897 Manuel utilisateur
molex
molex 207129 Series Manuel utilisateur
molex
molex 35768 Series Manuel utilisateur
molex
molex 207129 Series Manuel utilisateur
molex
molex 63816-1000 Manuel utilisateur
molex
molex 63811-7000 Manuel utilisateur
molex
molex 63827-5470 Manuel utilisateur
molex
molex 11-01-0185 Manuel utilisateur
molex
molex 207129 Series Manuel utilisateur
molex
molex 207129 Series Manuel utilisateur
molex
molex 63823-6370 Manuel utilisateur
molex
molex 207129 Series Guide de l'utilisateur
molex
molex 63827-7900 Manuel utilisateur
molex
molex 63825-6670 Manuel utilisateur
molex
molex 63827-2100 Manuel utilisateur
molex
molex 63816-0800 Manuel utilisateur
molex
molex 63827-0600 Manuel utilisateur
molex
molex 63825-9400 Guide de l'utilisateur
Manuels Outils de sertissage populaires d'autres marques
Panduit
Panduit CT-1000 Guide de l'administrateur
JST
JST CS 10 Manuel utilisateur
Danfoss
Danfoss ET4200 Manuel utilisateur
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Manuel utilisateur
TE Connectivity
TE Connectivity 2063528-1 Manuel utilisateur
Tyco Electronics
Tyco Electronics 69156-1 Manuel utilisateur
Textron
Textron ESG105L Manuel utilisateur
Tyco Electronics
Tyco Electronics 90035-3 Manuel utilisateur
Emerson
Emerson Klauke ES 20RMCCFB Manuel utilisateur
Continental Refrigerator
Continental Refrigerator PC150HD Manuel utilisateur
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur