MoJack EZ Guide de configuration

EZ Repair Instructions

Damaged Carrier Locking Pin Assembly

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

Review the Product Manual and Parts List for MoJack EZ at www.themojack.com. The detailed breakout

drawing includes all part numbers used in these instructions.

DO NOT attempt any repairs on your MoJack if there is a mower on the lift.

PROBLEM: Damaged Carrier Locking Pin Assembly

Probable

cause: Not pulling out on the Locking Pin when lowering your mower or Key Ring coming off

Solution: Replace Carrier Locking Pin #33

Tools needed:

•Hammer

•Small 1/8 pin punch

•Large 5/16 pin punch

•Two 19mm wrenches or two adjustable wrenches

Steps to make the repair:

Place the MoJack EZ lift on its side and position Crank Handle

#4 so that it cannot move.

•Using a small punch, tap all parts of the existing Roll Pin #32

out of the hole at the bottom of the Lift Screw #1.

•DO NOT try to drill out a broken Roll Pin as it may cause

damage to the hole.

•Remove Flat Washer #27 from Lift Screw.

EZ Repair Instructions

Damaged Carrier Locking Pin Assembly

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

Unscrew the Lift Screw out of the Bronze Nut #28 in the Carrier

Assembly #30, by turning the Crank Handle counter-clockwise.

Now that the Lift screw has been removed from the Carrier

Assembly, remove Carrier Bolt #2 (using two 19mm wrenches)

and Rear Carriage Roller #31 which will allow

you to take the Carrier Assembly off of the Tower #40.

•This may require pulling out the Carrier Locking Pin #33 if it

is engaged in one of the locking holes in the Tower.

Remove carrier bolt and roller 

•Examine the locking pin hole for old spring or other metal.

•Oil hole before going to the next step.

EZ Repair Instructions

Damaged Carrier Locking Pin Assembly

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

Insert the new Carrier Locking Pin with the new Spring-Locking

Pin #34 from the inside of the Carrier Assembly and fasten in

place on the outside with new Key Ring #35 (Safety Tag #42 is

optional).

•IMPORTANT: new Locking Pin is beveled and must be

inserted with the short part of the bevel on top and the long

part on the bottom.

Insert new locking pin and spring 

Fasten locking pin with key ring 

•Install the Carrier Assembly back on the Tower with the

Carrier Bolt and Rear Carriage Roller.

•This will require pulling out on the Key Ring.

•Caution: do not over-tighten the Carrier Bolt as the Rear Roller

needs to turn freely.

Make sure the two Front Carriage Rollers #29 are in place below

the new Bronze Nut and to the left and right side.

EZ Repair Instructions

Damaged Carrier Locking Pin Assembly

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

•Thread the Lift Screw down from the top into the new Bronze

Nut by rotating the Crank Handle clockwise.

•The two Front Carriage Rollers should be on the left and

right of the Lift Screw as it passes below the Bronze Nut.

•Continue rotating until the Lift Screw goes through the

welded tab at the bottom of the Tower.

10)

Apply new Flat Washer on Lift Screw and hammer the new Roll

Pin (bevel end first) into the hole using a large punch.

EZ Repair Instructions

Damaged Carrier Locking Pin Assembly

If additional help is needed, please call MoJack Customer Service: 1-877-575-3173.

11)

•Grease (or oil) top and bottom of new Flat Washer and the

new Lift Screw.

•This might be a good time to do the yearly maintenance on

your MoJack EZ. Consult your Product Manual, page 17, for

the Maintenance Schedule

12)

Before attempting to load your mower, test raising and lowering

the Lift Arm to make sure your MoJack EZ is working properly.

Autres manuels pour EZ

Table des matières

Autres manuels MoJack Système de levage

MoJack

MoJack EZ Instructions d'installation

MoJack

MoJack MoJackPRO Instructions d'installation

MoJack

MoJack PRO Instructions d'installation

MoJack

MoJack XT Instructions d'installation

MoJack

MoJack EZ Guide de configuration

MoJack

MoJack HDL 45501 Instructions d'installation

MoJack

MoJack ZR 350 Manuel utilisateur

MoJack

MoJack EZ Lift Instructions d'installation

MoJack

MoJack WorkBench Instructions d'installation

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur