Modena WF 730 Manuel du propriétaire
User
Manual Book
Washing Machine
Tiziano Series
WF 730
1
Thank you for your trust in choosing MODENA products for your household
needs. With your satisfaction as our priority, we constantly aim to deliver stylishly
designed products equipped with state-of-the-art technology to assist you in
your daily activities.
This is your guidebook containing everything you need to know about our
product. Please reach out to us if you need further assistance or other
information via our Customer Care or our official website www.modena.com.
2
CONTENTS PAGE.
• Introduction 20
• Part 1 : Name of Parts 22
• Part 2 : Understanding Control Panel 22
• Part 3 : First Step Before Installation 23
• Part 4 : Installation 23
• Part 5 : How to Use 25
• Part 6 : Maintenance 30
• Part 7 : Precaution Action 33
• Part 8 : Troubleshooting 34
• Part 9 : Specification 36
• Appendix 1: International Textile Care Label 37
• Appendix 2: Useful Hint For Dirt Vanishing 38
3
1. Control Panel 6. Inlet Valve (Cold) 11. Back Cover
2. Drawer Handle 7. Drain Hose Clips 12. Power plug
3. Door 8. Power Cord
4. Pump Case Cover 9. Drain Hose
5. Legs 10. Trasit Bolt
* Features and accessories depend on product series.
Part 1: Name of Parts
4
WF 730
When the installation is ready, make sure that the power supply has fuse with the specification of 15A,
220V, 50 Hz. When the heating function is used, the maximum current of the washing machine is 10A.
Make sure the power supply (current, voltage, and cable) fills the requirement to operate this appliance
on a normal load.
-The washing machine must be grounded, so whenever there is a problem, the current can be
conducted to the ground and minimize the risk of short circuits. If you are not sure if the washing
machine has been properly grounded or not, you can contact the experienced technician.
-The pressure of supply water is between 50kPa until 800kPa for the normal operation of the
washing machine. If the water supply is too low, the input water valve may not work normally or the
washing time becomes longer, and the display will show error code”E4”.
Part 2 : Understanding Control Panel
1
2
3
4
5
6
Part 3: First Step Before Installation
Control Panel Description
1. Program Select 5.Start/Pause Button
2. Temperature Button 6.Power Button
3. Spin Button
4.Delay Button
5
-Check all connections on input water supply, valve, and faucet to avoid water leakage.
-The result of the washing machine depends on the effectiveness of the detergent. The dirt on the
clothes may not be able to vanish by using bad quality detergent. Please clean the dirt on the
clothes like explained on this book before being washed by washing machine.
Take the washing machine out from the cardboard box and put it on a flat and sturdy floor. Don’t place
the washing machine on an incline, not flat, on the carpet, or on the wooden floor. Don’t place the
washing machine outdoor, and avoid a humid place that can cause damage.
1. Loosen all bolts behind the washing machine
-For transportation purposes, this washing
machine is locked with added polyfoam.
Before operating the washing machine,
loosen all bolts like the picture on the right.
-Fill the holes with supplied covers at the
back of the washing machine.
-Keep the polyfoam and bolts for transportation purposes and
use it again before transporting the washing machine.
Part 4: Installation
6
2. Leg adjustment
Install or place the washing machine at a temperature of no less than 0°C and not outdoors
because it may damage the programming controller
Note: To facilitate the installation, the feet may not be locked from the factory. Please
be sure to lock all the feet before adjusting the level!
3. Connect Inlet Valve
a) Water Inlet
- Connect the water hose to the water inlet on the back of the
washing machine.
- Connect the other side of the hose with the faucet.
- Don’t pull the hose if it is too short. Change to a longer hose.
7
or
- Check if there is leakage on connection
with the faucet.
b) Drainage
- If there is any leakage with the hose after the
connection, then repeat the steps to connect the
inlet hose.
- Do not bend the hose.
- Check for the inlet hose connection carefully
before using the washer every time.
Connect the drain hose
- The drain hose should be placed at a height of
65-100cm above the floor. Otherwise, it can
cause poor drainage.
- You can use the supplied drain hose support
bracket to loop the drain hose down into the
wall, standpipe or laundry tub.
- Make sure all the hose connections are
properly and tightly installed.
8
The end of the drain hose cannot be submerged
in water to make the washer work properly.
4. Connecting with electricity
- Make sure the voltage used is 220 volts and 50 Hz.
- Insert the power cord to the socket that is connected to the
ground.
- Avoid using extension cables, adapters and multiple sockets.
!
Attention!
Before operating the machine, it is suggested to check things as follows:
- Is the washing machine door closed properly?
- Is the water faucet opened?
- Is the drain hose placed correctly?
- Is the electricity connected?
In every washing make sure that:
- The connector of water supplies are safe, the water tap is turned on and the
drain hose has been placed in the right position.
- Cycle Options (P) or the power button is OFF.
Part 5: How to Use
9
- Then, with dry hands, plug the power cord into the socket.
- Sort / sorting clothes to be washed by the type of fabric / material.
- Make sure there are no objects (such as coins, safety pins, etc.) in the pocket
of the laundry that will be washed because it may damage the washing
machine, filters, and clothes itself.
- Open the washing machine door.
- Put in the clothing that will be washed (make sure the weight of the clothing
put into the washing machine does not exceed the capacity of the washing
machine) and close the washing machine door.
Detergent Drawer
The detergent drawer contains these parts:
- Detergent container for Prewash I → Powder detergent
- Detergent container for main wash II → Powder or liquid detergent
- Container for softener. ( ).
Caution: Don’t open the drawer during washing process.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Modena Rondelle
Modena
Modena Semplice Series Manuel du propriétaire
Modena
Modena WF 0532 WSR Manuel du propriétaire
Modena
Modena WT 0820 UGWH Manuel du propriétaire
Modena
Modena WT 1081 WTM Manuel du propriétaire
Modena
Modena WF 1156 Manuel du propriétaire
Modena
Modena WT 1121 WAM Manuel du propriétaire
Modena
Modena WF 0652 WSR Manuel du propriétaire
Modena
Modena WF Series Manuel utilisateur
Modena
Modena WF 1030 VDWH Manuel du propriétaire
Modena
Modena Calma Series Manuel du propriétaire
