Mobeye I110 Manuel utilisateur

User manual

Mobeye®i110

SW version 7N

Table of content

1. Introduction 1

2. To get ready in four steps 2

2.1 Step 1: SIM Card 2

2.2 Step 2: insert the batteries 2

2.3 Step 3: Program the phone numbers 3

2.4 Step 4: Check the settings 3

3. Switching the motion detector on/off 4

3.1 Switching on 4

3.2 Switching off 4

4. Mobeye settings 5

4.1 Configuration 5

4.2 Installation code 6

4.3 SMS custom text 6

4.4 Telephone numbers 7

4.5 SMS on/off 7

4.6 Call on/off 7

4.7 Sensor sensitivity 7

4.8 Entry delay 7

4.9 Entry indication 8

4.10 Siren 8

4.11 Exit indication 8

4.12 Temperature alarm 8

4.13 Adjusting the temperature 8

4.14 Interval test message 9

4.15 Setting the current time and date 9

4.16 User code 9

5. Advanced options 10

5.1 Request settings 10

5.2 Reset to factory settings 10

5.3 Leave the menu 10

5.4 Position of Mobeye 11

5.5 Test GSM network strength 12

6. Issue solving 13

7. Technical data 14

Attention! Very important

This user manual contains important guidelines for the installation and

usage of the Mobeye®i110. Please read these thoroughly before you start

using the Mobeye®!

In case of damage caused by disregarding the guidelines, the warranty

becomes void.

The user must regularly check the proper functioning of the Mobeye®. The

manufacturer cannot be held liable for any damage or loss caused by any

incorrect use or incorrect functioning of the Mobeye® i110.

Safety guidelines

 The permitted ambient temperature during operation may not be

exceeded (not lower than -10°C and not higher than 55°C).

 The device is intended for use in dry and clean places.

 Protect the device from moisture, heat and water splashing. Not intended

for external use.

 The guidelines for the battery usage must be regarded.

 Do not expose the device to strong vibrations.

 Do not let it fall from height.

 Do not use in an environment where any inflammable gases, vapours or

dust are present or could be present.

 Repair of the device may only be carried out by people, trained for

Mobeye®repair.

 If the device must be repaired, only original replacement components

may be used. The use of different parts may lead to damage of the

Mobeye®.

Use in accordance with the regulations

The purpose of this device in accordance with the regulations is the

generation of SMS text messages and telephone calls after detection of

motion by the motion detector or after a temperature was measured that

outreaches the programmed limits.

Other uses are not permitted and may invalidate the warrantee.

1. INTRODUCTION

The Mobeye i110 is an easy to install alarm

system that will notify you about a detection

using the built-in GSM communication

module.

To use the Mobeye i110 you will need a SIM-

card of any provider.

Typical applications are the security of places

without any power supply or the temporary security of properties.

The Mobeye i110 has the following features.

Alarm notifications after movement detection

In case of the detection of an intruder, the Mobeye i110 will send an SMS

text message to your phone(s). The Mobeye i110 will also call the phone

numbers in order to be sure the message is not missed. It is possible to set

the siren sound. Following the standby period of 5 minutes, the Mobeye will

resume alerting you to new movement.

Alarm notifications after detection of out of range temperature

It is possible to program a minimum and/or maximum temperature alert in to

the Mobeye i110. It will monitor the actual temperature of its environment

and send an alert as soon as the temperature reaches the limit.

Low battery message

The Mobeye i110 will send an SMS text message when the batteries need

to be replaced. When you receive this message, you need to change the

batteries as soon as possible, although the Mobeye i110 will continue to

function for a short time following the message. Even when the Mobeye

i110 is unset, it will measure the battery strength and send the message.

Private numbers or Mobeye Internet Portal

The Mobeye i110 sends alarm messages to one or two telephone numbers.

As an option the Mobeye i110 can be connected to the Mobeye Internet

Portal for extended functionality. Please refer to www.mobeye.eu for more

information.

2. TO GET READY IN FOUR STEPS

To get started with the Mobeye i110 only four steps are needed.

1. Place the SIM card in the Mobeye i110.

Make sure this SIM card is not secured by a PIN code.

2. Insert the four batteries.

3. Enter at least one phone number in the Mobeye i110.

4. Check the settings.

In this chapter these steps are explained.

2.1 STEP 1: SIM CARD

To use the Mobeye i110 a SIM card from any network is needed. On this

SIM card, the PIN code security needs to be disabled. If you have a SIM

card with PIN code, you can disable this using any mobile phone and switch

off the PIN code security. Please consult the manual for that mobile phone

for the procedure.

The SIM card needs to be inserted before the batteries. When using a

prepaid SIM card, take note of the available credit. Additionally it is wise to

set a recurrent test message in the menu so the card will be used at least

once a month.

Open the back cover (insert a key or screwdriver

into one of the deeper holes and pull back slowly).

Insert the SIM card in the holder. For

opening/closing, move the cover slightly.

2.2 STEP 2: INSERT THE BATTERIES

Insert the four lithium 3,0 volt batteries (CR123). When replacing the

batteries, all settings remain unchanged.

After inserting the SIM card and the batteries, the Mobeye i110 will perform

a self test taking 1 minute. During the test, the light is red. If the light is

flashing red, a problem with the SIM card is detected. A reason could be no

SIM card was placed, or the PIN code security of the SIM card was not

disabled.

Close the Mobeye i110 using the 4 screws.

2.3 STEP 3: PROGRAM THE PHONE NUMBERS

You need to program at least one phone number in the unit as alarm

receiving number.









Enter the phone number (e.g. 0712345678)



The light turns green and a confirmation melody is played.

The Mobeye i110 is ready to use.

2.4 STEP 4: CHECK THE SETTINGS

The settings can be sent to the programmed telephone number as SMS

text message. In this way you also check the correct working of the SIM

card.









Within ca. 30 seconds the set phone number will receive the list with

settings.

3. SWITCHING THE MOTION DETECTOR ON/OFF

3.1 SWITCHING ON

To activate the Mobeye i110 movement detector with your personal

installation code.





The light turns red shortly and an indication tone is started. This repetitive

tone will last during the exit delay of 60 seconds. As soon as the acoustic

signal stops, the Mobeye i110 is active.

If the installation code is entered incorrectly 3 times, the indicator turns red

and the Mobeye i110 will be blocked for 10 minutes.

3.2 SWITCHING OFF

To de-activate the Mobeye i110 movement detector with your personal

installation code.





The light switches to green and a confirmation melody is played.

4. MOBEYE SETTINGS

The Mobeye i110 settings can be changed via the keypad and SMS text

messages. First the method of programming is discussed, next the

explanation of the settings.

4.1 CONFIGURATION

To change the settings, please follow these instructions:



- light turns green

Enter the menu number (see list below)



Enter the new setting



is played

In the event of incorrect entries, the light turns red and a short beep will sound.



Following settings are possible:

Description

Options

Factory

setting

Change installation code

4 digit code

1111

Change 1st tel.nr.

Tel. number (0 to delete)

Change 2nd tel.nr.

Tel. number (0 to delete)

Sensor sensitivity

1,2

1 (high)

Entry delay

15, 30, 45 or 60

15 (sec.)

Interval test message

0-30 (days)

0 (no message)

Entry indication

0 (off), 1 (on), 2 (LED)

Siren

0 (off), 1 (on)

Exit indication

0 (off), 1 (on)

SMS on/off

0 (off), 1 (on)

Call on/off

0 (off), 1 (on)

Change minimum

temperature

000-050 (0 until 50ºC)

110-101 (-10 until -1 ºC)

999 = off

999

Change maximum

temperature

000-050 (0 until 50ºC)

110-101 (-10 until -1 ºC)

999 = off

999

Correction factor

temperature

01-09 (+1 to +9 ºC)

11-19 (-1 to -9 ºC)

00 (no correction)

Change user code

4 digit code

8888

Actual time

hhmm (e.g.1530)

Actual date

yyyymmdd (e.g. 20140331)

4.2 INSTALLATION CODE

The installation code is the code for switching on/off the active status. In the

active status the Mobeye i110 will detect movements. The installation code

is also needed to program the settings or activate the special functions. It is

possible to change the installation code to any 4-digit number. Please

change the code to make the unit more secure. If the installation code is

entered incorrectly 3 times, the indicator turns red and the Mobeye i110will

be blocked for 10 minutes.

4.3 SMS CUSTOM TEXT

A custom text can be added in the SMS text messages, to identify which

Mobeye i110unit sent the message. The second part of the SMS text



custom text is written before the standard text.

This custom text (max. 20 characters) can be programmed by sending an

SMS to the Mobeye i110. Changing the custom text cannot be done via the

keypad, only via sending an SMS text message.

Switch the Mobeye i110 into the programming mode. In this mode the GSM

module is switched on and is able to receive messages.

Enter your 4-



-> light turns green



First the light flashes red (interval ca. 1 sec). As soon as the light turns

green, the Mobeye i110is able to receive SMS-messages.

To program the custom text, send an SMS in following structure:

1111 NAME:myowntext

-

-

--defined text (max. 20 characters)

-Be aware of the space after 1111 and the colon after NAME

You will hear two short beeps in case of a correct command.



Autres manuels pour i110

Table des matières

Autres manuels Mobeye Système de sécurité

Mobeye

Mobeye PowerGuard CM2100 Manuel utilisateur

Mobeye

Mobeye argos i200 Manuel utilisateur

Mobeye

Mobeye ThermoGuard CM2200 Manuel utilisateur

Mobeye

Mobeye ThermoGuard TwinLog CML2255 Manuel utilisateur

Mobeye

Mobeye CM2500 Manuel utilisateur

Mobeye

Mobeye CM4000 Manuel utilisateur

Mobeye

Mobeye CM2500 Manuel utilisateur

Mobeye

Mobeye i110 Manuel utilisateur

Mobeye

Mobeye CM2500 Manuel utilisateur

Mobeye

Mobeye CMVXI-R Manuel utilisateur

Mobeye

Mobeye CombiGuard CM2600 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur