Mitsubishi M557 Manuel utilisateur
MODEL : M557
M700
USER’S MANUAL
BEDIENERHANDBUCH
MANUAL DEL USUARIO
MANUEL UTILISATEUR
MANUALE UTENTE
For future reference, record the serial
number of your display monitor in the
space below:
SERIAL No.
The serial number is located on the
rear cover of the monitor.
AUTO-SCANNING WITH DIGITAL CONTROL
COLOUR DISPLAY MONITOR
00PrintVersion_cover 24/5/01, 3:23 pm1
00PrintVersion_cover 24/5/01, 3:23 pm2
English
Deutsch
Español
Français
Italiano
01b_XChapterOpener 24/5/01, 3:23 pm1
01b_XChapterOpener 24/5/01, 3:23 pm2
English-1
English
Declaration of the Manufacturer
We hereby certify that the colour monitors
Diamond Scan 52(M557)
Diamond Scan 72(M700)
are in compliance with
Council Directive 73/23/EEC:
- EN 60950
Council Directive 89/336/EEC:
- EN 55022
- EN 61000-3-2
- EN 61000-3-3
- EN 55024
and marked with
NEC-Mitsubishi Electric Visual Systems Corporation
686-1, NISHIOI OI-MACHI
ASHIGARAKAMI-GUN
KANAGAWA 258-8533, JAPAN
01_english 24/5/01, 3:23 pm1
English-2
FCC Information
1. Use the attached specified cables with the Diamond Scan 52/72 colour monitor
so as not to interfere with radio and television reception.
(1) Please use the supplied power cable or equivalent to ensure FCC compliance.
(2) Shielded captive type signal cable.
Use of other cables may cause interference with radio and television
reception.
2. This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses, and can
radiate radio frequency energy, and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television
technician for additional suggestions. The user may find the following booklet,
prepared by the Federal Communications Commission, helpful: “How to Identify and
Resolve Radio-TV Interference Problems”. This booklet is available from the U.S.
Government Printing Office, Washington, D. C., 20402, Stock No. 004-000-00345-4.
Declaration of Conformity-United States only
Product Name: Colour Display Monitor
Type: Diamond Scan 52/72
Brand Name: MITSUBISHI
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
U.S Responsible party : NEC-Mitsubishi Electronics Display of America,Inc.
Adress : 1250 N. Arlington Heights Road ltasca, illinois 60143
Tel. No. : (630)467-3000
To identify this product, refer to the model number found on the product.
01_english 24/5/01, 3:23 pm2
English-3
English
Safety Instruction
Caution:
When operating the Diamond Scan 52/72 with a 220-240V AC power
source in Europe except UK, use the power cord provided with the
monitor.
In UK, a BS approved power cord with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cord is not
supplied with this equipment please contact your supplier.
When operating the Diamond Scan 52/72 with a 220-240V AC power
source in Australia, use the power cord provided with the monitor.
For all other cases, use a power cord that matches the AC voltage of
the power outlet and has been approved by and complies with the safety
standard of your particular country.
ENERGY STAR®Product
As an ENERGY STAR®Partner, NEC-Mitsubishi Electronics Display of
America Inc. has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency. The ENERGY STA R ®emblem does not
represent EPA endorsement of any product or service.
IBM is registered trademark of International Business Machines Corporation
Apple and Macintosh are registered trademarks of Apple Computer Inc.
Microsoft and Windows are registered trademarks of the Microsoft Corporation.
ENERGY STAR®is a U.S. registered mark.
All other trademarks or registered trademarks are property of their respective owners.
01_english 24/5/01, 3:23 pm3
English-4
Contents
The monitor box* should contains the following:
•The monitor with tilt / swivel base Diamond Scan 52 or Diamond
Scan 72
•Power cord
•Captive Signal Cable
•User’s manual
* Remember to save your original box and packing material to transport
or ship the monitor.
01_english 24/5/01, 3:23 pm4
English-5
English
Tilt / swivel base fixing,
removing
Fixing
This product consists of the monitor and the tilt / swivel base.
When fixing the tilt / swivel base to the monitor, please follow the steps
below.
•Push the hooks of the tilt / swivel base into the holes at the bottom of
the monitor.
•Then slide the tilt / swivel base forward.
•Then the latch above the tilt / swivel base engages it is secure.
Removing
Please removing the tilt / swivel base when transporting for repair.
•Push down the latch of the monitor and pull out the tilt / swivel base.
•Slide backward the tilt / swivel base from the front of the monitor.
•Pull out the tilt / swivel base from the holes of the monitor.
1. For correct use of monitor, completely attach tilt / swivel base to
the monitor.
2. To avoid self injury or damage to the monitor, attach and remove tilt /
swivel base with care.
01_english 24/5/01, 3:23 pm5
English-6
Quick Start
To attach the monitor to your system, follow these
instruction:
1. Turn off the power to your computer and the monitor.
2. If necessary, install the display card. For more information, refer to
the display card manual.
3. For the PC: Connect the 15-pin mini D-SUB of the captive signal
cable to the connector of the display card in your system (Figure A.1)
Tighten all screws.
For the Mac: Connect the Macintosh Cable Adapter (not included) to
the monitor connector on the Macintosh (Figure B.1). Attach the
15-pin mini D-SUB end of the captive signal cable to the Macintosh
cable adapter on the computer (Figure B.1). Tighten all screws.
4. Connect one end of the power cord to the monitor and the other end
to the power outlet (Figure C.1).
5. Turn on the monitor (Figure D.1) and the computer.
6. This completes the installation.
NOTE: If you have any problems, please refer to the
Troubleshooting section of this User‘s Manual.
Captive Signal Cable
15-pin-mini-D-SUB
Figure A.1
01_english 24/5/01, 3:23 pm6
Ce manuel convient aux modèles suivants
2
Table des matières
Langues :
Autres manuels Mitsubishi Moniteur
Mitsubishi
Mitsubishi Diamond Pro 930SB Manuel utilisateur
Mitsubishi
Mitsubishi JC-17W41 Manuel utilisateur
Mitsubishi
Mitsubishi Mitsubishi Diamondtron UWG RDF225WG RDF225WG... Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Pro 91TXM Manuel utilisateur
Mitsubishi
Mitsubishi HL6955K Series Manuel utilisateur
Mitsubishi
Mitsubishi DiamondPoint UX21LCD Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Scan SD5800C Manuel utilisateur
Mitsubishi
Mitsubishi HL6915K series Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Pro 2070SB Manuel utilisateur
Mitsubishi
Mitsubishi 2060u Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Pro 750SB Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Pro 930SB Manuel utilisateur
Mitsubishi
Mitsubishi LCD1855NX-BK Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Plus 200 Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Pro 87TXM Manuel utilisateur
Mitsubishi
Mitsubishi DiamondPoint NX86LCD Manuel utilisateur
Mitsubishi
Mitsubishi DiamondPoint NXM76LCD Manuel utilisateur
Mitsubishi
Mitsubishi Diamond Plus, Diamond Pro 93 SB, 750 SB Manuel utilisateur
Mitsubishi
Mitsubishi FHL7156 series Manuel utilisateur
Mitsubishi
Mitsubishi 230SB Manuel utilisateur
