Mitsubishi 4G1 series Manuel d'instructions

11A

MITSUBISHI

ENGINE

4G1 SERIES (E-W)

WORKSHOP MANUAL

Engine ................................

Pub. No. PWEE9520-B

FOREWORD

This Workshop Manual contains procedures for

removal, disassembly, inspection, adjustment,

reassembly and installation, etc. for service

mechanics.

All information, illustrations and product

descriptions contained in this manual are current

as at the time of publication. We, however, reserve

the right to make changes at any time without

prior notice or obligation.

FILING INSTRUCTION

Please keep these manual pages in the binder

No. BN940001.

File these pages according to the signs

“Added”, “Revised” and “Deleted” on the “List

of effective pages” which are interpreted

below.

Added:

File the pages with this sign additionally in

your manual.

Revised, Deleted:

Replace the existing pages with the

corresponding pages with this sign.

Missing sheets will be supplied upon request.

EMitsubishi Motors Corporation July 1999

INTRODUCTION

Classification of Major Maintenance/Service Points

When there are major points relative to maintenance and servicing procedures

(such as essential maintenance and service points, maintenance and service stan-

dard values, information regarding the use of special tools, etc.), these are

arranged together as major maintenance and service points and explained in

detail.

AA": Indicates that there are essential points for removal or disassembly.

"AA: Indicates that there are essential points for installation or reassembly.

Maintenance and Servicing Procedures

(1) A diagram of the component parts is

provided near the front of each section in

order to give the reader a better under-

standing of the installed condition of

component parts.

(2) The numbers provided within the diagram

indicate the sequence for maintenance and

servicing procedures.

: Indicates a non-reusable part.

The tightening torque is provided where

applicable.

DRemoval steps:

The part designation number corresponds

to the number in the illustration to indicate

removal steps.

DDisassembly steps:

The part designation number corresponds

to the number in the illustration to indicate

disassembly steps.

DInstallation steps:

Specified in case installation is impossible

in reverse order of removal steps. Omitted

if installation is possible in reverse order

of removal steps.

DReassembly steps:

Specified in case reassembly is impossible

in reverse order of disassembly steps.

Omitted if reassembly is possible in reverse

order of disassembly steps.

Symbols for Lubrication, Sealants and Adhesives

Information concerning the locations for

lubrication and for application of sealants

and adhesives is provided, by using sym-

bols, in the diagram of component parts, or

on the page following the component parts

page, and explained.

: Grease (multipurpose grease unless

there is a brand or type specified)

: Sealant or adhesive

: Brake fluid, automatic transmission fluid

or air conditioner compressor oil

: Engine oil or gear oil

EXPLANATION OF MANUAL CONTENTS

4. Thermo valve (engines with EGR)

(20) 5.

Thermo valve

Indicates the

section num-

ber.

Indicates the

group title.

Indicates the

section title.

Indicates the

group number.

Indicates the

page number.

Denotes tightening

torque.

Denotes non-reusable part.

This number corresponds to

the number appearing in

“Removal steps”,

“Disassembly steps”,

“Installation steps” or

“Reassembly steps”.

Operating procedures, cau-

tions, etc. on removal, installa-

tion, disassembly and reas-

sembly are described.

Issue date Publication number-Revision code

4G1 ENGINE (E-W) - Water Pump and Water Hose 11A-6-1

6. WATER PUMP AND WATER HOSE

REMOVAL AND INSTALLATION <SOHC-CARBURETOR>

Removal steps

1. Water hose

2. Water hose

3. Water hose

5. Thermo valve

6. Water temperature gauge unit

7. Water inlet timing

8. Thermostat

9. Thermostat case

10.Gasket

11.Water inlet pipe

12.O-ring

13.O-ring

14.Water pump

INSTALLATION SERVICE POINTS

WATER PUMP INSTALLATION

(1)Apply a 3 mm bead of form-in-place gasket (FIPG) to the

mounting surface.

Specified sealant:

Mitsubishi Genuine Part No. MD970389 or equivalent.

"FA

"DA

"CA

"BA

"AA

EMitsubishi Motors Corporation Nov. 1995 PWEE9520

"AA

227 Nm

27 Nm

11 Nm

923 Nm

22 Nm

12 Nm

13 Nm

INTRODUCTION

LIST OF EFFECTIVE PAGES

Page Revision

Code Date Remarks Page Revision

Code Date Remarks

Missing sheets will be supplied upon request.

PWEE9520-B

EJuly 1999Mitsubishi Motors Corporation Revised

11A-0-1 to 11A-0-4 Nov. 1995

11A-0-5 to 11A-0-7 A Dec. 1998

11A-1-1 and 11A-1-2 A Dec. 1998

11A-1-2a and 11A-1-2b A Dec. 1998

11A-1-3 to 11A-1-5 A Dec. 1998

11A-1-5a and 11A-1-5b A Dec. 1998

11A-1-6 and 11A-1-7 Nov. 1995

11A-2-1 Nov. 1995

11A-2-2 A Dec. 1998

11A-3-1 A Dec. 1998

11A-3-1a and 11A-3-1b A Dec. 1998

11A-3-2 and 11A-3-3 Nov. 1995

11A-4-1 A Dec. 1998

11A-4-2 to 11A-4-6 Nov. 1995

11A-5-1 and 11A-5-2 Nov. 1995

11A-5-2a and 11A-5-2b A Dec. 1998

11A-5-3 and 11A-5-4 Nov. 1995

11A-6-1 and 11A-6-2 Nov. 1995

11A-6-2a and 11A-6-2b A Dec. 1998

11A-6-3 to 11A-6-5 Nov. 1995

11A-7-1 and 11A-7-2 Nov. 1995

11A-7-2a A Dec. 1998

11A-7-2b B July 1999 Revised

11A-7-3 Nov. 1995

11A-7-4 B July 1999 Added

11A-8-1 A Dec. 1998

11A-8-1a and 11A-8-1b A Dec. 1998

11A-8-2 to 11A-8-10 A Dec. 1998

11A-9-1 A Dec. 1998

11A-9-1a and 11A-9-1b A Dec. 1998

11A-9-2 and 11A-9-3 Nov. 1995

11A-9-4 to 11A-9-10 A Dec. 1998

11A-10-1 A Dec. 1998

11A-10-2 to 11A-10-4 Nov. 1995

11A-11-1 Nov. 1995

11A-11-2 A Dec. 1998

11A-11-3 and 11A-11-4 Nov. 1995

11A-11-5 to 11A-11-8 A Dec. 1998

11A-12-1 to 11A-12-7 A Dec. 1998

PWEE9520-B

EJuly 1999Mitsubishi Motors Corporation Revised

Autres manuels pour 4G1 series

Table des matières

Autres manuels Mitsubishi Moteur

Mitsubishi

Mitsubishi Diesel Engine S12H-Y2PTAW-1 Manuel utilisateur

Mitsubishi

Mitsubishi S4S Manuel utilisateur

Mitsubishi

Mitsubishi S4E Manuel utilisateur

Mitsubishi

Mitsubishi GB101 Manuel utilisateur

Mitsubishi

Mitsubishi 4G9 series Manuel utilisateur

Mitsubishi

Mitsubishi S4Q2 Manuel utilisateur

Mitsubishi

Mitsubishi TLE Series (FA Manuel utilisateur

Mitsubishi

Mitsubishi GB290 Manuel utilisateur

Mitsubishi

Mitsubishi S12A2-PTA2 Manuel

Mitsubishi

Mitsubishi S16R Manuel utilisateur

Mitsubishi

Mitsubishi S16R-Y2PTAW2-1 Manuel utilisateur

Mitsubishi

Mitsubishi S6S-Y3T61HF Manuel utilisateur

Mitsubishi

Mitsubishi 4D68 Manuel d'instructions

Mitsubishi

Mitsubishi SL-Series Manuel utilisateur

Mitsubishi

Mitsubishi 4g63 Manuel utilisateur

Mitsubishi

Mitsubishi 4G1 series Manuel utilisateur

Mitsubishi

Mitsubishi L2A Manuel utilisateur

Mitsubishi

Mitsubishi GB30G Manuel utilisateur

Mitsubishi

Mitsubishi SS series Manuel utilisateur

Mitsubishi

Mitsubishi S6R-Y2PTAW-1 Manuel utilisateur

Mitsubishi

Mitsubishi 6A1 series Manuel utilisateur

Mitsubishi

Mitsubishi S16R Manuel

Mitsubishi

Mitsubishi S16R2-PTAW Manuel

Mitsubishi

Mitsubishi S4Q Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur