Mitsubishi Electric GOT2000 Series Manuel utilisateur

GRAPHIC OPERATION TERMINAL

User's Manual (Hardware)

GOT2000 Series

A - 1

Thank you for choosing Mitsubishi Graphic Operation Terminal (Mitsubishi GOT).

Read this manual and make sure you understand the functions and performance of the GOT thoroughly

in advance to ensure correct use.

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Note that the caution level may lead to a serious accident according to the circumstances. Always

follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

WARNING

Some failures of the GOT, communication unit or cable may keep the outputs on or off.

Some failures of a touch panel may cause malfunction of the input objects such as a touch switch.

An external monitoring circuit should be provided to check for output signals which may lead to a

serious accident.Not doing so can cause an accident due to false output or malfunction.

Do not use the GOT as the warning device that may cause a serious accident.

An independent and redundant hardware or mechanical interlock is required to configure the device

that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect output or malfunction.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting in

death or severe injury.

CAUTION Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

A - 2

[DESIGN PRECAUTIONS]

WARNING

When the GOT backlight has a failure, the GOT status will be as follows.Failure to observe this

instruction may result in an accident due to incorrect output or malfunction.

• GT27,GT25,GT23

When the GOT backlight has a failure, the POWER LED blinks (orange/blue) and the display

section dims. In such a case, the input by the touch switch(s) is disabled.

•GT21

When the GOT backlight has a failure, the display section dims. In such a case, the input by the

touch switches is disabled.

Even if the display section dims on the liquid crystal of the GOT, the input by the touch switch(s) may

remain enabled. This may cause a malfunction of the touch switch.

For example, if an operator assumes that the display section has dimmed because of the screen

save function and touches the display section to cancel the screen save, a touch switch may be

activated.

The GOT backlight failure can be checked with a system signal of the GOT.

The display section of the GOT is an analog-resistive type touch panel.

When multiple points of the display section are touched simultaneously, an accident may occur due

to incorrect output or malfunction.

•GT27

Do not touch three points or more simultaneously on the display section. Doing so may cause an

accident due to an incorrect output or malfunction.

• GT25,GT23,GT21

Do not touch two points or more simultaneously on the display section. Doing so may cause a

touch switch near the touched points to operate unexpectedly, or may cause an accident due to

an incorrect output or malfunction.

When programs or parameters of the controller (such as a PLC) that is monitored by the GOT are

changed, be sure to reset the GOT, or turn on the unit again after shutting off the power as soon as

possible.

Not doing so can cause an accident due to false output or malfunction.

If a communication fault (including cable disconnection) occurs during monitoring on the GOT,

communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.

For bus connection (GT27,GT25 Only) : The CPU becomes faulty and the GOT becomes

inoperative.

For other than bus connection : The GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant operation to the

system by using the switches of a device other than the GOT on the assumption that a GOT

communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

A - 3

[DESIGN PRECAUTIONS]

[MOUNTING PRECAUTIONS]

CAUTION

Do not bundle the control and communication cables with main-circuit, power or other wiring.

Run the above cables separately from such wiring and keep them a minimum of 100mm apart.

Not doing so noise can cause a malfunction.

Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

When the GOT is connected to the Ethernet network, the available IP address is restricted according

to the system configuration.

• When multiple GOTs are connected to the Ethernet network :

Do not set the IP address (192.168.3.18) for the GOTs and the controllers in the network.

• When a single GOT is connected to the Ethernet network :

Do not set the IP address (192.168.3.18) for the controllers except the GOT in the network.

Doing so can cause the IP address duplication.

The duplication can negatively affect the communication of the device with the IP address

(192.168.3.18).

The operation at the IP address duplication depends on the devices and the system.

Turn on the controllers and the network devices to be ready for communication before they

communicate with the GOT.

Failure to do so can cause a communication error on the GOT.

When the GOT is subject to shock or vibration, or some colors appear on the screen of the GOT, the

screen of the GOT might flicker.

WARNING

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the option unit onto/from the GOT. (GT27,GT25 Only)

A - 4

[MOUNTING PRECAUTIONS]

[WIRING PRECAUTIONS]

CAUTION

Use the GOT in the environment that satisfies the general specifications described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

When mounting the GOT to the control panel, tighten the mounting screws in the specified torque

range with a Phillips-head screwdriver No.2.

• GT27,GT25,GT23

Specified torque range (0.36 N•m to 0.48 N•m)

•GT21

Specified torque range (0.20 N•m to 0.25 N•m)

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the

GOT.

When mounting a unit on the GOT, tighten the mounting screws in the following specified torque

range.

• GT27,GT25

When loading the communication unit or option unit other than wireless LAN unit to the GOT, fit it

to the connection interface of the GOT and tighten the mounting screws in the specified torque

range (0.36 N•m to 0.48 N•m) with a Phillips-head screwdriver No.2.

When loading the wireless LAN unit to the GOT, fit it to the side interface of GOT and tighten the

mounting screws in the specified torque range (0.10 N•m to 0.14 N•m) with a Phillips-head

screwdriver No.1.

When the GOT is installed vertically, its side interface is positioned on the bottom.

To prevent the falling of the wireless LAN communication unit from the side interface, install or

remove the unit while holding it with hands.

• GT2103-P

When mounting the SD card unit on the GOT, fit it to the side of the GOT and tighten the tapping

screws in the specified torque range (0.3 N•m to 0.6 N•m) with a Phillips-head screwdriver No.2.

Under tightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, failure or malfunction due to the damage of the screws or unit.

When closing the USB environmental protection cover, fix the cover to the GOT by pushing the

[PUSH] mark on the latch firmly to comply with the protective structure.(GT27,GT25 Only)

Remove the protective film of the GOT.

When the user continues using the GOT with the protective film, the film may not be removed.

In addition, for the models equipped with the human sensor function, using the GOT with the

protective film may cause the human sensor not to function properly

Operate and store the GOT in environments without direct sunlight, high temperature, dust, humidity,

and vibrations.

When using the GOT in the environment of oil or chemicals, use the protective cover for oil.

Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT.

WARNING

Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

A - 5

[WIRING PRECAUTIONS]

CAUTION

Make sure to ground the FG terminal and LG terminal of the GOT power supply section to the

protective ground conductors dedicated to the GOT with a ground resistance of 100 Ωor less. (GT21

does not have the LG terminal.)

When tightening the terminal screws, use a Phillips-head screwdriver No.2.

Tighten the terminal screws of the GOT power supply section in the following specified torque range.

• GT27,GT25,GT23

Specified torque range (0.5 N•m to 0.8 N•m)

For a terminal processing of a wire to the GOT power supply section, use the following terminal.

• GT27,GT25,GT23

Use applicable solderless terminals for terminal processing of a wire and tighten them with the

specified torque.

Not doing so can cause a fire, failure or malfunction.

•GT21

Connect a stranded wire or a single wire directly, or use a rod terminal with an insulation sleeve.

Correctly wire the GOT power supply section after confirming the rated voltage and terminal

arrangement of the product.

Not doing so can cause a fire or failure.

Tighten the terminal screws of the GOT power supply section in the following specified torque range.

• GT27,GT25,GT23

Specified torque range (0.5 N•m to 0.8 N•m)

•GT21

Specified torque range (0.22 N•m to 0.25 N•m)

Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.

Not doing so can cause a fire, failure or malfunction.

The module has an ingress prevention label on its top to prevent foreign matter, such as wire offcuts,

from entering the module during wiring.

Do not peel this label during wiring.Before starting system operation, be sure to peel this label

because of heat dissipation. (GT27,GT25 Only)

Plug the communication cable into the GOT interface or the connector of the connected unit, and

tighten the mounting screws and the terminal screws in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

Plug the QnA/ACPU/Motion controller(A series) bus connection cable by inserting it into the

connector of the connected unit until it "clicks".

After plugging, check that it has been inserted snugly.

Not doing so can cause a malfunction due to a contact fault.(GT27,GT25 Only)

A - 6

[TEST OPERATION PRECAUTIONS]

[STARTUP/MAINTENANCE PRECAUTIONS]

WARNING

Before performing the test operations of the user creation monitor screen (such as turning ON or

OFF bit device, changing the word device current value, changing the settings or current values of

the timer or counter, and changing the buffer memory current value), read through the manual

carefully and make yourself familiar with the operation method.

During test operation, never change the data of the devices which are used to perform significant

operation for the system.

False output or malfunction can cause an accident.

WARNING

When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

Correctly connect the battery connector.

Do not charge, disassemble, heat, short-circuit, solder, or throw the battery into the fire.

Doing so will cause the battery to produce heat, explode, or ignite, resulting in injury and fire.

Before starting cleaning or terminal screw retightening, always switch off the power externally in all

phases.

Not switching the power off in all phases can cause a unit failure or malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

A - 7

[STARTUP/MAINTENANCE PRECAUTIONS]

[TOUCH PANEL PRECAUTIONS]

CAUTION

Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental

pulling of the cables or can cause a malfunction due to a cable connection fault.

When unplugging the cable connected to the unit, do not hold and pull from the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable

connection fault.

Do not drop the module or subject it to strong shock. A module damage may result.

Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

Before touching the unit, always touch grounded metals, etc. to discharge static electricity from

human body, etc.

Not doing so can cause the unit to fail or malfunction.

Use the battery manufactured by Mitsubishi Electric Corporation.

Use of other batteries may cause a risk of fire or explosion.

Dispose of used battery promptly.

Keep away from children.Do not disassemble and do not dispose of in fire.

Be sure to shut off all phases of the external power supply before replacing the battery or using the

dip switch of the terminating resistor.

Not doing so can cause the unit to fail or malfunction by static electricity.

CAUTION

For the analog-resistive film type touch panels, normally the adjustment is not required.

However, the difference between a touched position and the object position may occur as the period

of use elapses.

When any difference between a touched position and the object position occurs, execute the touch

panel calibration.

When any difference between a touched position and the object position occurs, other object may be

activated.

This may cause an unexpected operation due to incorrect output or malfunction.

A - 8

[PRECAUTIONS WHEN THE DATA STORAGE IS IN USE]

WARNING

If the SD card is removed from drive A of the GOT while being accessed by the GOT, the GOT may

stop processing data for about 20 seconds.

The GOT cannot be operated during this period.

The functions that run in the background including a screen updating, alarm, logging, scripts, and

others are also interrupted.

Before removing the SD card, check the following items.

• GT27,GT25,GT23

Check that the SD card access LED is off before removing the SD card.

•GT21

Disable the SD card access in the GOT utility, and then check that the SD card access LED is off

before removing the SD card.

CAUTION

If the data storage is removed from the GOT while being accessed by the GOT, the data storage and

files may be damaged.

Before removing the data storage from the GOT, check the SD card access LED, system signal, or

others to make sure that the data storage is not accessed.

Turning off the GOT while it accesses the SD card results in damage to the SD card and files.

When using the GOT with an SD card inserted, check the following items.

• GT27,GT25,GT23

When inserting a SD card into the GOT, make sure to close the SD card cover.

Not doing so causes the data not to be read or written.

•GT21

When inserting an SD card into the SD card unit, make sure to enable the SD card access in the

GOT utility in advance.

Not doing so causes the data not to be read or written.

When removing the SD card from the GOT, make sure to support the SD card by hand as it may pop

out.

Not doing so may cause the SD card to drop from the GOT, resulting in a failure or break.

When inserting a USB device into a USB interface of the GOT, make sure to insert the device into

the interface firmly.

Not doing so may cause the USB device to drop from the GOT, resulting in a failure or break.

Before removing the USB device from the GOT, follow the procedure for removal on the utility screen

of the GOT.

After the successful completion dialog is displayed, remove the USB device by hand carefully.

Not doing so may cause the USB device to drop from the GOT, resulting in a failure or break.

Autres manuels pour GOT2000 Series

Table des matières

Autres manuels Mitsubishi Electric Moniteur

Mitsubishi Electric

Mitsubishi Electric LDT322V Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT65IL Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT321V Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 56P-QF60LCU Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric VS-60HS12U Guide de l'utilisateur

Mitsubishi Electric

Mitsubishi Electric LM55S1 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric DR854 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MDT521S Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric TFV6708SKHKW Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT32IV Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric DT1151 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT322V Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT323V Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT46IV2 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MDT521S Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric RS232/485/LAN Serial Communication Control Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 2107e Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric E1063 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MLM300 Manuel de la liste des pièces

Mitsubishi Electric

Mitsubishi Electric LDT651P Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MDT652S Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LDT462V Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MLM300 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MDT55IS Manuel

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation