Mitsubishi Electric FR-A7NS Manuel utilisateur

FR-A7NS INSTRUCTION MANUAL

INVERTER

INSTRUCTION MANUAL

INVERTER

Plug-in option

HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

FR-A7NS

SSCNET III communication function

PRE-OPERATION INSTRUCTIONS

INSTALLATION

WIRING

IB(NA)-0600308ENG-B(0812) MEE Printed in Japan Specifications subject to change without notice.

RESTRICTIONS ON THE

FUNCTIONS

PRECAUTIONS

ALARM INDICATION DEFINITIONS

AND CORRECTIVE ACTIONS

INVERTER SETTING AND

DISPLAY

SSCNET III COMMUNICATION

STATUS

TROUBLESHOOTING

A-1

Thank you for choosing this Mitsubishi Inverter plug-in option.

This instruction manual gives handling information and

precautions for use of this equipment. Incorrect handling might

cause an unexpected fault. Before using the equipment, please

read this manual carefully to use the equipment to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about

safety matters

Do not attempt to install, operate, maintain or inspect this

product until you have read through this instruction manual and

appended documents carefully and can use the equipment

correctly. Do not use this product until you have a full

knowledge of the equipment, safety information and

instructions.

In this instruction manual, the safety instruction levels are

classified into "WARNING" and "CAUTION".

Assumes that incorrect handling may

cause hazardous conditions, resulting

in death or severe injury.

Assumes that incorrect handling may

cause hazardous conditions, resulting

in medium or slight injury, or may

cause physical damage only.

Note that even the level may lead to a serious

consequence according to conditions. Please follow the

instructions of both levels because they are important to

personnel safety.

WARNING

CAUTION

SAFETY INSTRUCTIONS

WARNING

•While power is on or when the inverter is running, do not

open the front cover. You may get an electric shock.

•Do not run the inverter with the front cover or wiring cover

removed. Otherwise, you may access the exposed high-

voltage terminals and charging part and get an electric shock.

•If power is off, do not remove the front cover except for wiring

or periodic inspection. You may access the charged inverter

circuits and get an electric shock.

•Before starting wiring or inspection, check to make sure that

the indication of the inverter operation panel is off, wait for at

least 10 minutes after the power supply has been switched off,

and check that there are no residual voltage using a tester or

the like. The capacitor is charged with high voltage for some

time after power off and it is dangerous.

•Any person who is involved in the wiring or inspection of this

equipment should be fully competent to do the work.

•Always install the plug-in option before wiring. Otherwise,

you may get an electric shock or be injured.

•Do not touch the plug-in option with wet hands. Otherwise

you may get an electric shock.

•Do not subject the cables to scratches, excessive stress,

heavy loads or pinching. Otherwise you may get an electric

shock.

A-2

2. Injury Prevention

3. Additional Instructions

Also note the following points to prevent an accidental failure,

injury, electric shock, etc.

1) Transportation and mounting

2) Trial run

3) Usage

4) Maintenance, inspection and parts replacement

5) Disposal

6) General instruction

CAUTION

•Apply only the voltage specified in the instruction manual to

each terminal. Otherwise, burst, damage, etc. may occur.

•Ensure that the cables are connected to the correct terminals.

Otherwise, burst, damage, etc. may occur.

•Always make sure that polarity is correct to prevent damage, etc.

Otherwise, burst, damage may occur.

•While power is on or for some time after power-off, do not touch

the inverter as it is hot and you may get burnt.

CAUTION

•Do not install or operate the plug-in option if it is damaged or

has parts missing.

•Do not stand or rest heavy objects on the product.

•Check that the mounting orientation is correct.

•Prevent other conductive bodies such as screws and metal

fragments or other flammable substance such as oil from

entering the inverter.

CAUTION

•Before starting operation, confirm and adjust the parameters.

A failure to do so may cause some machines to make

unexpected motions.

WARNING

•Do not modify the equipment.

•Do not perform parts removal which is not instructed in this

manual. Doing so may lead to fault or damage of the inverter.

CAUTION

•When parameter clear or all parameter clear is performed,

reset the required parameters before starting operations.

Each parameter returns to the initial value.

•For prevention of damage due to static electricity, touch

nearby metal before touching this product to eliminate static

electricity from your body.

CAUTION

•Do not test the equipment with a megger (measure insulation

resistance).

CAUTION

•Treat as industrial waste.

All illustrations given in this manual may have been drawn with

covers or safety guards removed to provide in-depth

description. Before starting operation of the product, always

return the covers and guards into original positions as specified

and operate the equipment in accordance with the manual.

CONTENTS 

1 PRE-OPERATION INSTRUCTIONS 1

1.1 Inverter Type ......................................................................................................................................1

1.2 Unpacking and Product Confirmation .............................................................................................2

1.2.1 Packing confirmation ......................................................................................................................................7

1.2.2 Parts ...............................................................................................................................................................8

1.3 Caution................................................................................................................................................9

1.4 Operation Overview .........................................................................................................................10

2 INSTALLATION 12

2.1 Pre-Installation Instructions ...........................................................................................................12

2.2 Shaft number Setting.......................................................................................................................13

2.3 Installation Procedure .....................................................................................................................14

3 WIRING 16

3.1 System configuration (when FR-A7AP is used)............................................................................16

3.2 Wiring example (when FR-A7AP is used)......................................................................................18

3.3 SSCNET III cable ..............................................................................................................................20

3.3.1 SSCNET III cable laying ...............................................................................................................................24

3.4 Wiring................................................................................................................................................26

4 SSCNET III COMMUNICATION STATUS 32

5 INVERTER SETTING AND DISPLAY 35

5.1 Parameter List ..................................................................................................................................35

5.2 Operation Mode Setting ..................................................................................................................36

5.2.1 Operation mode indication............................................................................................................................36

5.2.2 Operation mode switchover method.............................................................................................................37

5.3 Operation at Communication Error Occurrence...........................................................................40

5.3.1 Alarm and measures ....................................................................................................................................40

5.4 Inverter Reset ...................................................................................................................................41

5.5 Setting SSCNET III communication function ................................................................................42

5.5.1 Pr.499 SSCNET III operation selection ........................................................................................................42

5.5.2 Pr.379 SSCNET III rotation direction selection.............................................................................................47

5.5.3 Pr.449 SSCNET III input filter setting ...........................................................................................................48

5.5.4 Pr.52 DU/PU main display data selection.....................................................................................................48

5.5.5 Pr.185 JOG terminal function selection........................................................................................................49

5.5.6 Pr.800 Control method selection ..................................................................................................................49

6 RESTRICTIONS ON THE FUNCTIONS 50

6.1 Function Restriction List.................................................................................................................50

6.2 Inverter Parameter List....................................................................................................................53

6.3 Inverter I/O Terminal Function List ................................................................................................69

6.3.1 Input terminal function ..................................................................................................................................69

6.3.2 Output terminal function ...............................................................................................................................72

III

7 PRECAUTIONS 74

8 ALARM INDICATION DEFINITIONS AND CORRECTIVE ACTIONS 75

9 TROUBLESHOOTING 79

1PRE-OPERATION INSTRUCTIONS

1.1 Inverter Type

The inverter type, 55K and 75K stated in this Instruction Manual differs according to each -NA, -EC, -CH(T)

versions. Refer to the following correspondence table for each inverter type. (Refer to the instruction manual

of each inverter for the inverter type.)

For example, "for the 75K or more" indicates "for the FR-A740-01440-NA or more" in the case of FR-A740

of NA version.

NA EC CH

A700

FR-A720-55K FR-A720-02150-NA 

FR-A720-75K FR-A720-02880-NA 

FR-A740-55K FR-A740-01100-NA FR-A740-01800-EC FR-A740-55K-CHT

FR-A740-75K FR-A740-01440-NA FR-A740-02160-EC FR-A740-75K-CHT

PRE-OPERATION INSTRUCTIONS

1.2 Unpacking and Product Confirmation

Take the plug-in option out of the package, check the unit name, and confirm that the product is as you

ordered and intact.

This product is a plug-in option for the FR-A700 series inverter assembled in and after January 2007.

Refer to the table below to check the SERIAL (Serial No.) indicated on the inverter rating plate or package.

(1) NA specification

z200V class

Inverter Type

Label on

Product

Package

Identification

Symbol

Lower Third

and Second

Number of

TC Number

on Rating

Plate

SERIAL

(Upper

Three

Numbers of

SERIAL)

FR-A720-00030-NA Without G5 Q71

FR-A720-00050-NA P71

FR-A720-00080/

00110-NA

Without G5 Q71

<G> G7 D71

FR-A720-00175-NA Without G5 R71

<G> G7 D71

FR-A720-00240/

00330-NA

Without G5

Q71

FR-A720-00460-NA P71

FR-A720-00610 to

00900-NA R71

FR-A720-01150 to

01750-NA Q71

FR-A720-02150-NA P71

FR-A720-02880/

03460-NA M71

Inverter Type

Label on

Product

Package

Identification

Symbol

Lower Third

and Second

Number of

TC Number

on Rating

Plate

SERIAL

(Upper

Three

Numbers of

SERIAL)

PRE-OPERATION INSTRUCTIONS

z400V class

Inverter Type

Label on

Product

Package

Identification

Symbol

Lower Third

and Second

Number of

TC Number

on Rating

Plate

SERIAL

(Upper

Three

Numbers of

SERIAL)

FR-A740-00015 to

00310-NA

Without G5 Q71

<G> G7 E71

FR-A740-00380/

00440-NA

Without G5 Q71

<G> G7 F71

FR-A740-00570 to

00860-NA

Without G5 P71

<G> G7 E71

FR-A740-01100-NA Without G5 P71

<G> G7 D71

FR-A740-01440

to 02660-NA

Without G5 M71

<G> G7 E71

FR-A740-03250-NA Without G5 N71

<G> G7 F71

FR-A740-03610-NA Without G5 M71

<G> G7 F71

FR-A740-04320/

04810-NA

Without G5 M71

<G> G7 E71

FR-A740-05470-NA Without G5 N71

<G> G7 E71

FR-A740-06100-NA Without G5 M71

<G> G7 D71

FR-A740-06830-NA Without G5 J71

<G> G7 D71

FR-A740-07700/

08600-NA

Without G5 M71

<G> G7 D71

FR-A740-09620-NA Without G5 N71

<G> G7 D71

Inverter Type

Label on

Product

Package

Identification

Symbol

Lower Third

and Second

Number of

TC Number

on Rating

Plate

SERIAL

(Upper

Three

Numbers of

SERIAL)

PRE-OPERATION INSTRUCTIONS

(2) EC specification

* For the FR-A740-00770 to 12120-EC

Check the SERIAL indicated on the Serial number sticker shown below.

To check the SERIAL, the front cover must be removed.

For the removal of the front cover, refer to the inverter manual.

Inverter Type

Label on

Product

Package

Identification

Symbol

Lower Third

and Second

Number of

TC Number

on Rating

Plate

SERIAL

(Upper

Three

Numbers of

SERIAL)

FR-A740-00023 to

00126-EC

Without G5 or G6 M71

<G> G7 or G8 F71

FR-A740-00170/

00250-EC

Without G5 or G6 N71

<G> G7 or G8 F71

FR-A740-00310/

00380-EC

Without G5 or G6 M71

<G> G7 or G8 F71

FR-A740-00470/

00620-EC

Without G5 N71

<G> G7 G71

FR-A740-00770 to

12120-EC*



L71 or F71

Inverter Type

Label on

Product

Package

Identification

Symbol

Lower Third

and Second

Number of

TC Number

on Rating

Plate

SERIAL

(Upper

Three

Numbers of

SERIAL)

VUW

FR-CA70-EC 71

SERIAL

Control unit type

SERIAL (Serial No.)

Month

Serial number sticker example

The SERIAL consists of 1 version symbol, 2 numeric characters

or 1 numeric character and 1 alphabet letter indicating year and

month, and 3 numeric characters indicating control number.

Month is indicated as 1 to 9, X (October), Y (November), and Z

(December).

Year

Symbol

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Onduleur

Mitsubishi Electric

Mitsubishi Electric FR-D720S-008SC Instructions de fonctionnement

Mitsubishi Electric

Mitsubishi Electric FR-A820-00046 (0.4K) Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-CS84-295-60 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Feuille d'instructions

Mitsubishi Electric

Mitsubishi Electric FR-A7AY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-K-400-U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-A820-04750-GF Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-D720-0.4K Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 700 Series Manuel du propriétaire

Mitsubishi Electric

Mitsubishi Electric FR-A7NL Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.1K Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-CV-7.5K Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Freqrol FR-U120S-EC Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-E540 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FREQROL HC Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-A7AP Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Climaveneta i-BX-004-013M Guide de configuration

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-V5NS Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.1K Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-ABR-(H)0.4K Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur