Mitsubishi Electric 800 Series Manuel utilisateur

INSTRUCTION MANUAL

INVERTER

Plug-in option PRE-OPERATION INSTRUCTIONS 1

INSTALLATION 2

CONNECTING THE 24 V EXTERNAL

POWER SUPPLY 3

FR-E8DS E KIT

24 VDC input

Safety instructions

Thank you for choosing this Mitsubishi Electric inverter plug-in option.

This Instruction Manual provides handling information and precautions for use of this product. Incorrect handling might cause an unexpected

fault. Before using this product, read all relevant instruction manuals carefully to ensure proper use.

Please forward this Instruction Manual to the end user.

Electric Shock Prevention

WARNING

Do not remove the front cover or the wiring cover while the power of the inverter is ON, and do not run the inverter with the front cover or the

wiring cover removed, as the exposed high voltage terminals or the charging part of the circuitry can be touched. Doing so may cause an

electric shock.

Even if power is OFF, do not remove the front cover of the inverter except for wiring or periodic inspection, as the inside of the inverter is

charged. Doing so may cause an electric shock.

Before wiring or inspection, check that the LED display of the operation panel is OFF. Any person who is involved in wiring or inspection shall

wait for at least 10 minutes after the power supply has been switched OFF and check that there is no residual voltage using a tester or the

like. For some time after the power-OFF, a high voltage remains in the smoothing capacitor, and it is dangerous.

Any person who is involved in wiring or inspection of this product shall be fully competent to do the work.

The plug-in option must be installed before wiring. Otherwise you may get an electric shock or be injured.

Do not touch the plug-in option or handle the cables with wet hands. Doing so may cause an electric shock.

Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Doing so may cause an electric shock.

WARNING Incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only material

damage.

Do not attempt to install, operate, maintain or inspect this product until you have read this Instruction Manual and appended documents

carefully. Do not use this product until you have a full knowledge of this product mechanism, safety information and instructions. In this

Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

CAUTION

Note that even the level may lead to a serious consequence depending on conditions. Be sure to follow the

instructions of both levels as they are critical to personnel safety.

CAUTION

Injury Prevention

Additional Instructions

The following instructions must be also followed. If the product is handled incorrectly, it may cause unexpected fault, an injury, or an electric

shock.

CAUTION

The voltage applied to each terminal must be as specified in the Instruction Manual. Otherwise an explosion or damage may occur.

The cables must be connected to the correct terminals. Otherwise an explosion or damage may occur.

The polarity (+ and -) must be correct. Otherwise an explosion or damage may occur.

While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Doing so may cause burns.

CAUTION

Transportation and installation

Do not install or operate the plug-in option if it is damaged or has parts missing.

Do not stand or rest heavy objects on the product.

Ensure the mounting orientation of this product is correct.

Prevent conductive items such as screws and metal fragments, or flammable substances such as oil from entering this product.

If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood packages enter this product, the product may

be damaged. Prevent the entry of fumigant residuals or use an alternative method such as heat disinfection. Note that sterilization or

disinfection of wood packages should be performed before packing the product.

Trial operation

Before starting operation, confirm or adjust the parameter settings. Failure to do so may cause some machines to make unexpected

motions.

WARNING

Usage

Do not modify the equipment.

Do not remove any part which is not instructed in this manual. Doing so may lead to fault or damage of the product.

CAUTION

Usage

As all parameters return to their initial values after Parameter clear or All parameter clear is performed, the parameters must be set again as

required before the operation is started.

Static electricity in your body must be discharged before you touch the product.

Maintenance, inspection and parts replacement

Do not carry out a megger (insulation resistance) test.

Disposal

The inverter must be treated as industrial waste.

General instruction

For clarity, illustrations in this Instruction Manual may be drawn with covers or safety guards removed. Ensure all covers and safety guards

are properly installed prior to starting operation.

— CONTENTS —

Safety instructions 2

1 PRE-OPERATION INSTRUCTIONS 6

1.1 Unpacking and checking the product............................................................................................................................6

1.1.1 Product confirmation ............................................................................................................................................................. 6

1.1.2 SERIAL number check.......................................................................................................................................................... 7

1.2 Component names ..........................................................................................................................................................8

1.3 Specifications ..................................................................................................................................................................9

1.3.1 Input terminal specifications.................................................................................................................................................. 9

1.3.2 Availability of the inverter functions while the 24 V external power is supplied..................................................................... 9

2 INSTALLATION 10

2.1 Pre-installation instructions .........................................................................................................................................10

2.2 Installation procedure ...................................................................................................................................................10

2.3 Wiring..............................................................................................................................................................................18

3 CONNECTING THE 24 V EXTERNAL POWER SUPPLY 22

APPENDIX 25

Appendix 1 Instructions for compliance with the EU Directives ....................................................................................25

Appendix 2 Instructions for EAC .......................................................................................................................................26

Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products .....................................27

Appendix 4 Referenced Standard (Requirement of Chinese standardized law) ...........................................................28

Appendix 5 Compliance with the UK certification scheme .............................................................................................29

REVISIONS 31

6PRE-OPERATION INSTRUCTIONS

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and checking the product

Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact.

This product is a plug-in option made for the FR-E800 series inverters.

1.1.1 Product confirmation

Check the enclosed items.

Plug-in option: 1 Mounting screw (M3 × 8

mm): 2

(Refer to page 11, page

13.)

Junction connector: 1

(Refer to page 11, page

13.)

Option small cover: 1

(Refer to page 13.)

Front cover for plug-in

option: 1

(Refer to page 11, page

13.)

Recessed neck screw

(M3 × 7): 1

(Refer to page 11, page

13.)

Straight spacer: 1

(Refer to page 11, page

13.)

L-shaped spacer: 1

(Refer to page 11, page

13.)

Hexagon spacer: 2

(Refer to page 11, page

13.)

PRE-OPERATION INSTRUCTIONS 7

1.1.2 SERIAL number check

The FR-E8DS is available for the inverters manufactured in December 2021 or later.

Check the SERIAL number printed on the rating plate or on the package of the inverter.

NOTE

• When the FR-E8DS is installed to an incompatible inverter, operation cannot be guaranteed.

The SERIAL consists of two symbols, three characters indicating the

production year and month, and six characters indicating the control

number.

The last two digits of the production year are indicated as the Year, and

the Month is indicated by 1 to 9, X (October), Y (November), or Z

(December).

Rating plate

SERIAL

INPUT :XXXXX

MODEL :FR-E820-0008-1

OUTPUT:XXXXX

SERIAL:XXXXXXXXXXX

MADE IN XXXXX

Country of origin

Rating plate example

□□ ○○ ○ ○○○○○○

Symbol

SERIAL

Year Month Control number

8PRE-OPERATION INSTRUCTIONS

1.2 Component names

Symbol Name Description Refer to

page

a Mounting hole Used to fix this product to the inverter by inserting a mounting screw

or a spacer. 10

b Terminal block Connected to a 24 V external power supply. 18

c Board mounted option connector Used to connect this product to the option connector of the inverter. 10

d LED (operation status indicator) ON while the 24 V external power is supplied. 23

Front view Rear view

+24

(a)

(a) (c)

(a)

(d)

(b)

PRE-OPERATION INSTRUCTIONS 9

1.3 Specifications

1.3.1 Input terminal specifications

1.3.2 Availability of the inverter functions while the 24 V external power is supplied

*1 Terminal FM is provided in the FM type inverter. Terminal AM is provided in the AM type inverter.

*2 For details, refer to the FR-E800 Instruction Manual (Function).

NOTE

• During the 24 V external power supply operation, the inverter operation is disabled.

• During the 24 V external power supply operation, up to four inverters can be connected.

Terminal symbol Common Terminal function description Rated specification

+24 SD

Use the 24 V external power supply to turn ON/OFF I/O terminals,

keep the operation panel ON, and carry out communication during

communication operation even at power-OFF state of inverter's

main circuit power supply.

Input voltage: 23.5 to 26.5 VDC

Input current: 0.7 A or less

Function Availability when the FR-E8DS is installed (main circuit power supply is OFF)

Reading/writing parameters Enabled

Monitor display Enabled (The monitor items related to the main circuit power supply are not available.*2)

Operation panel indication / key

operation Enabled (The RUN key is disabled.)

Input terminals Enabled (Terminals 2, 4, and 10 and the start signals (STF and STR) are disabled.)

Output terminals Enabled (Terminals FM and AM and the output signals related to the main circuit power supply are

disabled.*1*2)

Fault indication Enabled

USB connector Enabled

Others

• Parameter unit (FR-PU07), LCD operation panel (FR-LU08), and enclosure surface operation panel

(FR-PA07) are available.

• Terminal PC cannot be used for 24 VDC power supply.

• Terminal 10 cannot be used for 5 VDC power supply.

10 INSTALLATION

2INSTALLATION

2.1 Pre-installation instructions

Check that the inverter's input power and the control circuit power are both OFF.

2.2 Installation procedure

Installing the option

The FR-E800 series inverter has only one plug-in option connector.

NOTE

• Ensure the control circuit terminals are wired before installing the plug-in option. They cannot be wired after the plug-in

option is installed.

• When installing the plug-in option, prevent cables being caught between parts. Otherwise the inverter and the option may be

damaged.

CAUTION

• Do not install or remove this product while the inverter power is ON. Doing so may damage the inverter or this product.

• To avoid damage due to static electricity, static electricity in your body must be discharged before you touch the product.

Autres manuels pour 800 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Onduleur

Mitsubishi Electric

Mitsubishi Electric FR-A7ND E kit Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 700 Series Feuille d'instructions

Mitsubishi Electric

Mitsubishi Electric melpto d series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-F500 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-A800 Plus Series Feuille d'instructions

Mitsubishi Electric

Mitsubishi Electric FR-A820-04750-GF Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-S540E-0.4K-EC Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 700 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-V5AX Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-E720-0.1K Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Climaveneta i-BX-004-013M Guide de configuration

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 700 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-F820-04750 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-D720-008 Feuille d'instructions

Mitsubishi Electric

Mitsubishi Electric FR-F840-00023 Feuille d'instructions

Mitsubishi Electric

Mitsubishi Electric FR-A520-0.4K -55K Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-E8TR Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-S500 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 700 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-F820-00046 Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur