Mitsubishi Electric MELSEC Q Series Manuel utilisateur

Channel Isolated Digital-Analog Converter Module

User's Manual

-Q62DA-FG

-GX Configurator-DA (SW2D5C-QDAU-E)

A-1 A-1

SAFETY PRECAUTIONS 

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of

the programmable controller system, refer to the user’s manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING " and "

CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

Do not write data into the "System area" of the buffer memory of intelligent function modules.

Also, do not use any "Use prohibited" signals as an output signal to an intelligent function

module from the programmable controller CPU.

Writing data into the "System area" or outputting a signal for "Use prohibited" may cause a

programmable controller system malfunction.

CAUTION

Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100mm(3.9inch) or more from each other.

Not doing so could result in noise that may cause malfunction.

At power-on, a voltage may be applied or a current may flow between output terminals for a

moment. In such case, wait until the analog output becomes stable to start controlling the

external device.

! !

WARNING

CAUTION

A-2 A-2

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications

contained in the user's manual of the CPU module to use.

Using this programmable controller in an environment outside the range of the general

specifications may cause electric shock, fire, malfunction, and damage to or deterioration of the

product.

While pressing the installation lever at the bottom of module, insert the module fixing tab into the

fixing hole in the base unit until it stops.

Improper installation may result in malfunction, breakdown or the module coming loose and

dropping.

Securely fix the module with screws if it is subject to vibration during use.

Tighten the screws within the range of specified torque.

If the screws are loose, it may cause the module to fallout, short circuits, or malfunction.

If the screws are tightened too much, it may cause damage to the screw and/or the module,

resulting in fallout, short circuits or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause damage to the module.

In the system where a CPU module supporting Online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of Online module change in this manual.

Do not directly touch the conductive area or electronic components of the module.

Doing so may cause malfunction or failure in the module.

[Wiring Precautions]

WARNING

After wiring, attach the included terminal cover to the module before turning it on for operation.

Failure to do so may result in electric shock.

CAUTION

Individually ground the FG terminal of the programmable controller with a ground resistance of

100Ωor less.

There is a risk of electric shock or malfunction.

Use applicable solderless terminals and tighten them with the specified torque.If any solderless

spade terminal is used, it may be disconnected when the terminal screw comes loose, resulting

in failure.

Tighten the terminal screws within the specified torque range.

Undertightening can cause short circuit, fire, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

A-3 A-3

CAUTION

Be careful not to let foreign matter such as sawdust or wire chips get inside the module.

They may cause fires, failure or malfunction.

A protective film is attached to the top of the module to prevent foreign matter, such as wire

chips, from entering the module during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

[Starting and Maintenance Precautions]

WARNING

Do not touch any terminal while power is on.

Doing so will cause electric shock or malfunction.

Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws or module mounting screws.

Failure to do so may cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

CAUTION

Do not disassemble or modify the modules.

Doing so could cause failure, malfunction injury or fire.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause failure or malfunction of the module.

In the system where a CPU module supporting Online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of Online module change in this manual.

Do not install/remove the module to/from the base unit, or the terminal block to/from the module

more than 50 times after the first use of the product. (IEC 61131-2 compliant)

Failure to do so may cause malfunction.

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

A-4 A-4

[Disposal Precautions]

CAUTION

When disposing of this product, treat it as industrial waste.

A-5 A-5

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A-6 A-6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

May, 2002 SH (NA)-080281E-A First printing

Feb., 2003 SH (NA)-080281E-B Correction

Safety precautions, Section 2.1, 3.2.2, 3.4.1, 3.4.19, 5.1, 5.2.2, 5.6.3,

7.3.3, 7.3.4, 7.3.5, 7.3.6, 7.4, Appendix 1.2, Appendix 1.3

May, 2003 SH (NA)-080281E-C Correction

Section 2.2, 3.4.1, 3.4.18, 3.4.19, 4.5, 4.6, 5.3.1

May, 2004 SH (NA)-080281E-D Addition

Section 8.2.5

Correction

Section 2.2, 3.1.3, 3.2.1, 3.4.4, 7.1, 7.3.1 to 7.3.6

Aug., 2004 SH (NA)-080281E-E Correction

Section 1.1, 5.1, 5.2.1, 5.2.2, 5.3.1, 5.3.2, 5.3.3, 5.6.1, 5.6.2

Addition

Section 5.6.3, 5.7, 5.8

Oct., 2004 SH (NA)-080281E-F Correction

Safety precautions, Section 2.1, 3.1.1, 4.1, 6.3.1

Sep., 2005 SH (NA)-080281E-G Correction

Safety precautions, Section 2.1, 5.2.2, 6.3.2

Mar., 2006 SH (NA)-080281E-H Correction

Safety precautions, Appendix 1

Jan., 2007 SH (NA)-080281E-I Correction

Section 3.2.1, 3.4.2, 4.5, 4.6, 6.2.1, 6.2.2, 6.3.1, 6.3.2

Jan., 2008 SH (NA)-080281E-J Addition

Section 2.2

Correction

SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations

Section 1.1, Section 2.1, Section 2.3, Section 4.1, Section 4.6, Section

5.2.1, Section 5.2.2, Section 7.3.3, Section 7.3.5, Section 8.1, Appendix

1, Appendix 1.1, Appendix 2, Appendix 2.1, Appendix 2.2, Appendix 2.3

May, 2008 SH (NA)-080281E-K Correction

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, About the Generic Terms and Abbreviations, Section 2.1,

Section 4.1, Section 5.2.1, Section 5.2.2, Section 5.3.1, Section 5.3.3,

Chapter 7, Section 7.1

-7 A-7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Nov., 2010 SH (NA)-080281E-L Addition

CONDITIONS OF USE FOR THE PRODUCT, Section 3.4.17, Section

3.4.18, Section 3.4.19, Section 3.4.20, Appendix 3

Correction

SAFETY PRECAUTIONS, INTRODUCTION,

Compliance with the EMC and Low Voltage Directives,

About the Generic Terms and Abbreviations,

Section 1.1, Sections 2.1 to 2.3, Section 3.1, Section 3.1.1,

Section 3.1.2, Section 3.2, Section 3.2.1 to 3.2.6, Section 3.3.2,

Section 3.4.1 to 3.4.17, Section 3.4.19 to 3.4.23, Section 4.1, Section 4.3,

Section 4.4.2, Section 4.5, Section 4.6, Section 5.1, Section 5.2.1,

Section 5.3.1, Section 5.3.3, Section 5.4, Section 5.5, Section 5.6.1,

Section 5.6.2, Section 5.7, Chapter 6, Section 6.1, Section 6.2,

Section 6.2.1, Section 6.3, Section 6.3.1, Section 6.3.2, Chapter 7,

Section 7.1, Section 7.2, Section 7.3, Sections 7.3.1 to 7.3.6, Section 7.4,

Section 7.5, Section 8.1, Section 8.2.1 to 8.2.4, Section 8.2.5,

Section 8.2.6, Appendices 1.1 to 1.3, Appendix 2, Appendix 3,

Appendix 4

May, 2015 SH (NA)-080281E-M Correction

SAFETY PRECAUTIONS, Related Manuals, Compliance with the EMC

and Low Voltage Directives, About the Generic Terms and Abbreviations,

Section 2.1, Section 2.3, Section 3.1.2, Section 3.2.2, Section 3.4.23,

Section 4.3, Section 4.6, Section 5.2, Section 5.2.1, Section 5.2.2,

Section 6.2.2, Chapter 7, Section 7.1, Section 8.1, Appendix 4

Jan., 2020 SH (NA)-080281E-N Correction

Section 4.5, Section 8.2.4

Japanese Manual Version SH-080280-Q

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property

rights which may occur as a result of using the contents noted in this manual.

2002 MITSUBISHI ELECTRIC CORPORATION

A-8 A-8

INTRODUCTION

Thank you for purchasing the Mitsubishi Electric MELSEC-Q series programmable controllers.

Before using the product, please read this manual carefully to develop full familiarity with the functions and

performance of the Q series programmable controllers to ensure correct use.

CONTENTS

SAFETY PRECAUTIONS............................................................................................................................. A-

CONDITIONS OF USE FOR THE PRODUCT ............................................................................................ A-

REVISIONS ................................................................................................................................................... A-

INTRODUCTION........................................................................................................................................... A-

CONTENTS................................................................................................................................................... A-

ABOUT MANUALS ........................................................................................................................................A-12

COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES.......................................................A-12

ABOUT THE GENERIC TERMS AND ABBREVIATIONS...........................................................................A-13

PRODUCT STRUCTURE..............................................................................................................................A-14

1 OVERVIEW 1-

1 to 1-

1.1 Features ...................................................................................................................................................1-

2 SYSTEM CONFIGURATION 2-

1 to 2-

2.1 Applicable Systems..................................................................................................................................2-

2.2 Precautions on System Configuration.....................................................................................................2-

2.3 Checking Function Version, Serial Number, and Software Version.......................................................2-

3 SPECIFICATIONS 3-

1 to 3-38

3.1 Performance Specifications .....................................................................................................................3-

3.1.1 Performance specifications list .........................................................................................................3-

3.1.2 I/O conversion characteristics...........................................................................................................3-

3.1.3 Accuracy............................................................................................................................................3-

3.2 Function List .............................................................................................................................................3-

3.2.1 Analog output HOLD/CLEAR function..............................................................................................3-

3.2.2 Analog output test during programmable controller CPU STOP..................................................... 3-10

3.2.3 Output monitor function..................................................................................................................... 3-11

3.2.4 Warning output function .................................................................................................................... 3-12

3.2.5 Rate control function ......................................................................................................................... 3-13

3.2.6 Disconnection detection function...................................................................................................... 3-14

3.3 I/O Signals for the Programmable Controller CPU ................................................................................. 3-19

3.3.1 List of I/O signals............................................................................................................................... 3-19

3.3.2 Details of I/O signals ......................................................................................................................... 3-20

3.4 Buffer Memory.......................................................................................................................................... 3-25

3.4.1 Buffer memory assignment............................................................................................................... 3-25

3.4.2 D/A conversion enable/disable setting (buffer memory address 0: Un\G0).................................... 3-28

3.4.3 Digital value (buffer memory address 1, 2: Un\G1, Un\G2)............................................................. 3-28

3.4.4 Set value check code (buffer memory address 11, 12: Un\G11, Un\G12) ..................................... 3-29

3.4.5 Error code (buffer memory address 19: Un\G19) ............................................................................ 3-29

3.4.6 Setting range (buffer memory address 20: Un\G20)........................................................................ 3-30

Autres manuels pour MELSEC Q Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Contrôleurs

Mitsubishi Electric

Mitsubishi Electric Central Controller G-50A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC A1SD71-S2 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC-A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Mode d’emploi

Mitsubishi Electric

Mitsubishi Electric AE-200A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q66DA-G Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Mode d’emploi

Mitsubishi Electric

Mitsubishi Electric LE7-40GU Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric CR750 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric CC-Link IE Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PZ-61DR-E Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-4DA-ADP Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric WS0-CPU0 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric XD3500U Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PAR-30MAA Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R RD78G4 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Manuel de service

Mitsubishi Electric

Mitsubishi Electric R60AD8-G Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur