Mitel DBC 220 01 Manuel utilisateur
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Telephone set DBC 220 01
mlundmarkQRASSII
1531-DBC 220 01 Uen D1 2016-03-07 2
NOTICE
The information contained in this document is believed to be accurate in all respects
but is not warranted by Mitel Networks™ Corporation (MITEL®). Mitel makes no
warranty of any kind with regards to this material, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose. The informa-
tion is subject to change without notice and should not be construed in any way as a
commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and
subsidiaries assume no responsibility for any errors or omissions in this document.
Revisions of this document or new editions of it may be issued to incorporate such
changes.
No part of this document can be reproduced or transmitted in any form or by any means
- electronic or mechanical - for any purpose without written permission from Mitel
Networks Corporation.
TRADEMARKS
The trademarks, service marks, logos and graphics (collectively "Trademarks")
appearing on Mitel's Internet sites or in its publications are registered and unregistered
trademarks of Mitel Networks Corporation (MNC) or its subsidiaries (collectively
"Mitel") or others. Use of the Trademarks is prohibited without the express consent from
tion. For a list of the worldwide Mitel Networks Corporation registered trademarks,
please refer to the website: http://www.mitel.com/trademarks.
© Copyright 2016, Mitel Networks Corporation
All rights reserved
TELEPHONE SET DBC 220 01
31531-DBC 220 01 Uen D1 2016-03-07
1 GENERAL
1.1 SCOPE
The digital telephone sets (DTS) and peripherals described in these installation instruc-
tions are to be used together with the Mitel exchanges ASB 501 04, ASB 150 02 or
equivalent.
The DTS is connected to a digital extension board, ELU28/3, or equivalent.
1.2 ENVIRONMENTAL REQUIREMENTS
The products covered in these installation instructions comply with the prerequisites
stipulated for placing in office and exchange room environments.
1531-DBC 220 01 Uen D1 2016-03-07 4
AIDS
2 AIDS
Wall mounting requires additional screws.
TELEPHONE SET DBC 220 01
51531-DBC 220 01 Uen D1 2016-03-07
3 PREPARATIONS
Verify that it is possible to connect an extension line and check that a line cord is avail-
able.
1531-DBC 220 01 Uen D1 2016-03-07 6
POWER EQUIPMENT
4 POWER EQUIPMENT
The DTS and its peripherals are powered from the extension line. Maximum power
consumption: 1.5 W
TELEPHONE SET DBC 220 01
71531-DBC 220 01 Uen D1 2016-03-07
5 EARTHING
The DTS and its peripherals need no special earthing.
1531-DBC 220 01 Uen D1 2016-03-07 8
CABLING
6 CABLING
Maximum line length between DTS and extension line unit (ELU28/3) using EKKX 0.5
mm (180 ohms/km) cable: 1000 m (3280 ft).
TELEPHONE SET DBC 220 01
91531-DBC 220 01 Uen D1 2016-03-07
7 INSTALLATION OF DTS
7.1 DELIVERY METHOD
The DTS body is delivered in a box together with one handset, one handset cord, two
feet, designation label and designation cover.
7.2 CONNECTION OF THE HANDSET
The handset cord shall be connected with one end (short uncoiled) to the handset and
the other end (long uncoiled) to the connector in the bottom of the telephone marked
HANDSET.Use the cord guide to secure the handset cord to the DTS. Choose the
proper guide to emerge the cord to the left or right side of the telephone.
7.3 CONNECTION TO THE EXTENSION LINE (NOT INCLUDED
IN THE BOX)
The line cord shall be connected in one end to the wall box, see 1 Connection of exten-
sion line on page 9 , and the other end to the connector in the bottom of the set marked
LINE.
Figure 1: Connection of extension line
7.4 WALL MOUNTING
• Mount two screws (diam. 5.5 max) vertically with 100 mm distance and 9.5 mm
space to the wall, see 2 Positions and dimensions for screws on page 10.
• Break away the two screw hole covers with e.g. a screwdriver.
1531-DBC 220 01 Uen D1 2016-03-07 10
INSTALLATION OF DTS
• Dismount and turn the hook around, see3 Changing the hook position on page
10
• If the adjustable feet are mounted they must be removed.
• Mount the telephone on the screws and press it down on the keyholes.
Figure 2: Positions and dimensions for screws
Figure 3: Changing the hook position
7.5 USING DBC 22X 01 PHONES TOGETHER WITH CT
ADAPTERS
When using a DBC 22x 01 phone together with a CT adapter, the phone must be
configured for short signals. Follow the steps below to configure the phone for short
signals:
Table des matières
Autres manuels Mitel Téléphone
Mitel
Mitel 8560 Manuel utilisateur
Mitel
Mitel MIVOICE OFFICE 400 6920 SIP Manuel utilisateur
Mitel
Mitel 6739 Manuel utilisateur
Mitel
Mitel SUPERSET 420 Manuel utilisateur
Mitel
Mitel 6970 Manuel utilisateur
Mitel
Mitel SX-2000 Light Guide de configuration
Mitel
Mitel M2008 Manuel utilisateur
Mitel
Mitel 6390 Manuel utilisateur
Mitel
Mitel 6710 Manuel utilisateur
Mitel
Mitel NETVISION PHONE Manuel utilisateur
Mitel
Mitel Superset 4025 Manuel utilisateur
Mitel
Mitel Superset 1000 Manuel utilisateur
Mitel
Mitel Inter-Tel 5000 Manuel utilisateur
Mitel
Mitel 6867i Premium Manuel utilisateur
Mitel
Mitel 6867i Premium Manuel utilisateur
Mitel
Mitel 8520 Manuel utilisateur
Mitel
Mitel Superset 4015 Manuel utilisateur
Mitel
Mitel 6867i Premium Manuel utilisateur
Mitel
Mitel MiVOICE 6930 Manuel utilisateur
Mitel
Mitel A5370 Manuel utilisateur
