MINOURA B60 Manuel utilisateur

Indoor Bicycle Trainer – instructions manual

Minoura Japan Headquarters Minoura North American Tech Center

(for all customers) (for U.S. residents only)

1197-1 Godo, Anpachi, Gifu 503-2305 Japan 1996 East Avenue, Hayward, CA 94541 U.S.A.

Phone: +81-584-27-3131 / Fax: +81-584-27-7505 Phone: 1-510-538-8599 / Fax: 1-510-538-5899

Email: [email protected] Email: [email protected]

www.minoura.jp

Made in Japan

B60-D (Non-Remote)

B60-R (Remote)

Read this instructions carefully before use

Tire Size Capacity Range<w/o Z-adaptor> 26 x 1.0 – 700 x 45c

<with Z-adaptor> 22 x 1-3/8 – 700 x 32c

(ver.1.0 2010/5)

(Shown image: B60-D)

IMPORTANT NOTICE

• For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other.

• Fits tire size between 26x1.0 and 700x45c. 29-inch is not compatible on this model.

To use 26x1.0" or smaller tire, install the optional Z-shaped Small Wheel Adaptor.

• Some assembly required. Use correct tools (10mm spanner & M4 hex wrench). Tools

are not supplied in the kit.

• Use the supplied rear quick release skewer for maximum stability.

Minoura is not responsible for any problem caused from using your own skewer.

(* Quick release skewer = A wheel axle device which allows mounting/disengaging the

wheel without any tool)

• If your bike wheel is not equiped with a quick release skewer but a standard hub nut

type axle, remove the black plastic Grommet (F-9) from the Right Side Coupling (F-1)

for better and safer tting.

Be sure that it is not possible to convert a hub nut type wheel axle to a quick rekease

skewer type unless replacing the wheel hub itself.

• Use on at and level oor or ground for your safety.

• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.

Tire-to-roller contact will eventually wear both your tire and the trainer roller. It's

normal.

• On B60-D (non-remote type), adjusting the resistance must be done when the bike

stopped. Do not operate the Dial Lever (EM-13) for changing the resistance power

while the rear wheel is spinning.

• Touching the spinning wheel and/or any other moving parts while training should

cause serious injury. Keep children and pets away from the trainer when in use.

• If you feel any strange noise or smell, stop using B60 immediately and contact the

retailer where you purchased.

• Any warranty will be void if you use B60 for other purpose than instructed.

Minorua offers 1-year limited warranty on the resistance unit and 5-year limited

warranty on the frame from the date of your purchase for any problem caused by

manufacturer's defect.

Any damage or problem caused by transporting process is not covered under warranty.

Any damage from shipping or moving must be made to the shipping company.

Read enclosed "Minoura Limited Warranty Policy" card for more detail.

- Page 2 -

F-1: Coupling (Right)

F-4: Coupling Cover

F-7: Hub Handle

F-9: Grommet

BF-5: Leg Rubber Cover (White)

BF-6: Leg Rubber

BF-9: B60 Main Frame (Black)

M5-2: Rubber Foot Cap (29mm)

MF-3: Micro Adjust Knob Set

B60 Schematics

BF-9

BF-5

BF-6 M5-2

MF-3

F-7

F-4

F-9

F-1

EM-1 EM-2

EM-3 EM-4

EM-5 EM-6 EM-17

EM-8

EM-9

EM-10

EM-1 EM-2

EM-3 EM-4

EM-5

EM-12

EM-13

EM-17

EM-8

EM-11

LM-10

<B60-D Non-Remote>

<B60-R Remote>

EM-1: Outer Cap EM-10: Cable Guide

EM-2: Axle Holder EM-11: Connecting Plate

EM-3: Drive Roller & Bearing EM-12: Magnet Plate (Dial)

EM-4: Main Housing EM-13: Dial Lever

EM-5: Alloy Plate EM-17: Flywheel (600g)

EM-6: Magnet Plate (Remote) GM-19: Remote Shifter

EM-8: Flywheel Cover LM-10: Base Plate

EM-9: Remote Base

- Page 3 -

BF-5

BF-6

GM-19

3. Fully open both legs and place B60 on a at and

level oor.

At this moment, make sure all 4 foot are

contacting the oor at once to sit on the oor

stable. (see Fig. B)

How To Setup Your B60 Trainer

2. Install the Roller Pressure Adjust Knob set (MF-3)

to the welded nut on the B60 frame. (see Fig. A)

- Page 4 -

1. Replace your rear wheel quick release skewer to the supplied one.

Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape.

If your bike is not equipped with quick release skewer and it's a hub nut type, you

should remove the black plastic Grommet (Skewer Nut Protector) (F-9) from the

right side coupling. Minoura doesn't guarantee the stability if you don't remove the

Grommet

You don't need the supplied quick release skewer if your wheel is a hub nut type.

It's not possible to convert your wheel from the hub nut type to the quick release

skewer type unless replacing the hub.

Required Tools: 1 x 10mm Spanner

1 x M4 Hex Wrench

Make sure the acorn shaped spring

direction is as shown in Fig. A.

Failure will cause difculty on rotating.

(Fig. A)

(Fig. B)

4. Place your rear wheel in between the couplings.

1) Turn the Hub Handle in the direction of

counter-clockwise to make the enough space

between the couplings.

You should almost fully open the coupling

for easier wheel installation. (see Fig. C)

2) Insert the left side (quick lever side) skewer into the left side coupling rst.

The quick lever shaft must be inserted into the cut-out on the coupling to hold the bike stable. Turn the

coupling to adjust the cut-out position prior to tightening the Hub Handle.

3) While keeping this position, slowly come down the bike to align the right side acorn nut to the right

side coupling.

4) Turn the Hub Handle clockwise to hold the rear wheel.

Once the rear wheel hub is stify caught between the couplings and you see the frame starts opening,

it's the bottom position. Stop tightening.

6) Turn the Hub Handle two more rotations. Do not try to over-tighten the Hub Handle.

Both right and left side couplings are

designed to suit the supplied quick release

skewer. The left side coupling must t

perfectly in the skewer head to get correct

stability. (see Fig. D)

Any skewer type which lever is located on

the end of the axle (see Fig. E) or the lever

will not be bent over right angle (see Fig. F)

cannot be used on B60.

(Fig. D)

(Fig. E) (Fig. F)

Do not try to over-tighten the Hub Handle

to keep the correct thightness of rear hub

clamping.

Too tight setting will cause damage to both

B60 and your bike frame.

Too loose setting may cause the bike to

come out of the trainer during use.

- Page 5 -

(Fig. C)

Be careful not to over-loosen the

Hub Handle. It will loosen the

inside nut and no longer proper

tightening can be expected.

6. The rear tire should sit in the almost center part of

the Drive Roller without touching any other parts.

(see Fig. I)

If the tire has touched the plastic parts (see Fig. K)

due to some reasons like the rear wheel is not trued

correctly or you have installed a too fat tire, you must

adjust the Mag unit position.

To do so, loosen the backside screws with M5 hex

wrench, adjust the roller position, then tighten the

screws again tightly. (see Fig. J)

5. Contact the Drive Roller to the rear tire by turning the Roller Pressure Adjust Knob clockwise. (see Fig. G)

The best position is that the roller compresses the tire in the depth of 3 - 4 mm. (see Fig. H)

- Page 6 -

(Fig. I)

(Fig. K)(Fig. J)

If the rear tire has touched any other parts than the Drive Roller, the certain part

should be damaged and your tire will wear out quickly.

(Fig. G) (Fig. H)

Please note too much and too less roller pressure will bring premature tire wear.

Keep correct roller pressure and maintain the air pressure in correct level before

using B60.

If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob.

TIPS

How To Adjust Resistance Level (B60-D)

B60-D provides 3 different resistance levels to suit your

training level.

To Increase Resistance Level:

Slide the Dial Lever toward "H" position.

To Decrease Resistance Level:

Slide the Dial Lever toward "L" position.

5. To remove the bike from B60, loosen the micro adjust knob rst, then loosen the Hub Handle.

If you remove the bike without changing the roller position, the next installation may become difcult

because the rear wheel has been pushed forward by the roller.

- Page 7 -

1. Wind the band around the handlebar or stem, and hook the metal ring to the gutter on the remote shifter

base. (see Fig. M-1)

3. The soft fabric band is pre-adjusted to t normal 22mm diameter handlebar.

If you need to mount onto an oversized or specially shaped handlebar or stem, adjust the band (see Fig. N).

At this moment, we suggest you to slide the guide pin downward (see the column) to loosen the band for

easier work.

121

B60-R features a convenient remote shifter lever. You can install it on the handlebar or stem, then you can

control the resistance power in 7 levels without necessary of getting off the bike.

Decrease

Increase

(Fig. M)

(Fig. N)

(Fig. O)

2. Flip up the lever to lock (see Fig. M-2). If it is loosened, adjust the band tighter as per instructed in the

following section.

4. To increase the resistance, twist the lever toward "H". To decrease the resistance, twist the lever towawrd

"L". (see Fig. O)

You can choose from 7 different levels to suit your desired workout level.

How To Adjust Resistance Level (B60-R)

(Fig. L)

If you wish to use the tire sized 26x1.0" or smaller,

you need to install the optional Z-shaped "Small

Wheel Adapter" between Base Plate and Mag unit to

raise up the roller height.

The direction of Z-adapter is xed so follow the

arrow printed on the top and make sure it's pointing

toward the front (toward your bike).

If the drive roller cannot reach the tire even if you

install the adaptor, make sure you have been installed

in correct direction.

Use the original cap head bolts for the Base Plate,

and use the supplied hex head bolts for the Mag unit.

How To Use Small Wheel Adaptor (Option)

Hex Head Bolt

Cap Head Bolt

Z-Adaptor

< in case of V270 >

Required Tools: 1 x 10mm Spanner

1 x M5 Hex Wrench

- Page 8 -

Why My Remote Shifter Doesn't Work Properly?

You may have a shifting problem that you cannot set at L

or H position properly due to the lengthened inner cable.

To x this problem, follow the steps to adjust the initial

cable tension.

1. Set your remote shifter at "H" position and remove

the shifter from your handlebar, then straighten the

cable as much as possible.

2. Pull out the plastic cover cap on foot of the remote

cable. (see Fig. P and Q)

3. Hold the inside adjusting screw and push it toward

the shifter, then adjust the locking nut to set the

cable tension properly. (see Fig. R)

4. Install the cover cap again.

(Fig. P)

(Fig. Q)

(Fig. R)

(Fig. S)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels MINOURA vélo d'appartement

MINOURA

MINOURA SmartTurbo KAGURA LSD9200 Manuel utilisateur

MINOURA

MINOURA RDA80 Manuel utilisateur

MINOURA

MINOURA B60-D Manuel utilisateur

MINOURA

MINOURA LiveRide LR340 Manuel utilisateur

MINOURA

MINOURA VFS150 Manuel utilisateur

MINOURA

MINOURA V270 Manuel utilisateur

MINOURA

MINOURA liveride lr240 Manuel utilisateur

MINOURA

MINOURA VFSG-9 Manuel utilisateur

MINOURA

MINOURA MAG-850 Manuel utilisateur

MINOURA

MINOURA LiveRide LR341 Manuel utilisateur

MINOURA

MINOURA M70-R Manuel utilisateur

MINOURA

MINOURA LiveRide FG220 Manuel utilisateur

MINOURA

MINOURA moz-roller Manuel utilisateur

MINOURA

MINOURA FG540 HYBRID ROLLER Manuel utilisateur

MINOURA

MINOURA MAG-500 Series Manuel utilisateur

MINOURA

MINOURA LiveRide LST9200 Manuel utilisateur

MINOURA

MINOURA MAG-850LW Series Manuel utilisateur

MINOURA

MINOURA MAG-850 Manuel utilisateur

MINOURA

MINOURA V270 Manuel utilisateur

MINOURA

MINOURA LiveRoll R720 Manuel utilisateur

MINOURA

MINOURA LiveRide LR960 Manuel utilisateur

MINOURA

MINOURA Minimag M20-D Manuel utilisateur

MINOURA

MINOURA SmartTurbo Kagura EHT1020 Manuel utilisateur

MINOURA

MINOURA M60-D Manuel utilisateur

Manuels vélo d'appartement populaires d'autres marques

Weslo

Weslo Vector 302 Guide de démarrage rapide

TOORX

TOORX BRX85 Manuel utilisateur

Matrix

Matrix KranKcycle Manuel utilisateur

Matrix

Matrix IC3 Manuel utilisateur

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Manuel utilisateur

Monark

Monark 827E Manuel utilisateur

Stamina

Stamina 1310 Manuel utilisateur

American Fitness

American Fitness SPR-BK1072A Manuel utilisateur

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Manuel utilisateur

BH FITNESS

BH FITNESS H9158H Manuel de l'opérateur

Body Sculpture

Body Sculpture BC-7220G Manuel utilisateur

Cateye

Cateye EC-2300 Manuel utilisateur

FYTTER

FYTTER RACER RC MSR Manuel utilisateur

Kikos

Kikos HM-9090M Manuel utilisateur

Pro-Form

Pro-Form 345 Zlx Bike Guide de l'utilisateur

Fuel Fitness

Fuel Fitness SU135-40 Manuel utilisateur

NordicTrack

NordicTrack Gxr 4.2 Bike Manuel utilisateur

Vision Fitness

Vision Fitness U70 Manuel utilisateur