Minebea CSD-912-73 Manuel utilisateur
III
GRAPHIC DIGITAL INDICATOR
CC-Link Interface
CSD-912-73
Instruction Manual
MINEBEA Co., Ltd.
Measuring Components Business Unit
EN294-1424
I
FOREWORD
Thank you very much for your purchasing Minebea’s Graphic Digital Indicator, model
CSD-912-73.
This manual explains the handling procedures and the notes when it would be used. Make
use of it properly after reading through the manual carefully.
Be sure to deliver the manual to the end user. Moreover, the end user should keep the
manual at hand after reading it over.
This manual is intended for the technical experts to read. When you read this instruction
manual, the program basic knowledge of Mitsubishi general-purpose sequencer and the
CC-Link interface are needed.
Marks and arrangements used in this manual
The following marks are attached to the explanation on the matters that indicate “Don’t do
this.”, “Take care” and “For reference”.
Be sure to read these items where these marks are attached.
Warning
Caution
Warning may cause injury or accident that may harm to the operator.
Don’t do these things described here.
It is a description when the occurrence only of assumption of danger by which the user owes injury when handling is
mistaken, and material damage is assumed.
Caution during operation and working.
Be sure to read the item to prevent malfunction.
II
About the view of this book
This instruction manual explains the connection method and use of the CC-Link interface
specification of the option for CSD-912 are explained. Please see the CSD-912 instruction
manual about other main body functions and a basic method of handling and notes.
CSD-912 instruction manual (DRW No. EN294-1404*)
Moreover, please refer to the instruction manual of sequencer and its CC-Link interface for
the sequencer program and CC-Link.
●CC-Link is an abbreviation of “Control & Communication Link”
III
Divisional history
Date Instruction manual No. Details of revised point
2011/02 DRW. NO.EN294-1424 First Version
IV
Index
FOREWORD
...................................................................................................................................................................... I
Marks and arrangements used in this manual
............................................................................................ I
About the view of this book
................................................................................................................................... II
Divisional history
......................................................................................................................................................... III
Index
................................................................................................................................................................................... IV
1．
General
....................................................................................................................................................................... 1
1-1. Features ...................................................................................................................................1
2．
Name and function of each point
............................................................................................................... 2
2-1. Rear panel for CC-Link I/F.......................................................................................................2
3．
Connecting method
............................................................................................................................................ 3
3-1. Connector pin configuration for communication..................................................................3
3-2. Notes of Connection................................................................................................................3
4．
Setting of CC-Link connecting
..................................................................................................................... 4
4-1. Changeover of CC-Link communication setting change screen..........................................4
4-2. Items of CC-Link setting .........................................................................................................4
5．
PLC memory explanation
................................................................................................................................ 6
5-1. Address....................................................................................................................................6
5-2. Address map............................................................................................................................7
6．
Operation method
.............................................................................................................................................. 26
6-1. Writing the set value (Special data area)..............................................................................26
6-2. Writing/Reading by general command.................................................................................26
6-3. Shift to status where it is possible to communicate...........................................................28
6-4. Error condition/Reset requesting flag..................................................................................28
6-5. CPU normal operation signal................................................................................................29
6-6. Calibration procedure by CC-Link communication ..........................................................30
7．
Specifications of interface
............................................................................................................................ 31
7-1. Specifications of CC-Link interface......................................................................................31
7-2. Accessories ...........................................................................................................................31
1
1．General
This unit is a remote device station of CC-Link Ver.1.10.
This unit can be connected with the mastering station of CC-Link Ver.1.10.
1-1.Features
Main features for CSD-912-73 are as follows:
（1） This unit can be controlled by using remote I/O and register of the sequencer, so the program volume
of the sequencer can be reduced.
（2） The wiring with the sequencer can be reduced.
2
2．Name and function of each point
2-1.Rear panel for CC-Link I/F
（1） Communication connector
Connector type terminal block for CC-Link interface.
Connector pin configuration for communication is as follows
※ Suitable plug : MSTB 2,5-ST-5,08 ABGY AU by PHOENIX CONTACT. ※to be attached.
※ “SLD” and “FG" are connected inside.
※ The internal circuit and photo coupler are insulated.
（2） Status LED
The communication status is expressed with two LED.
Status RUN ERR
Light off －Normal
Green LED
Light on Normal －
Red LED
Light on Hardware error Hardware error
Red LED
Light on/off －CRC error
Pin No. Signal name Contents
1 DA Signal line DA side
2 DB Signal line DB side
3 DG Signal line ground
4 SLD Shield
5 FG Frame ground
DA
DB
DG
SLD
FG
1 2 3 4 5
（2） Status LED
（1） Communication connecto
r
3
3．Connecting method
3-1.Connector pin configuration for communication
Refer to 2-1. Rear panel for CC-Link I/F (1), Connector for communication.
3-2.Notes of Connection
zWhen the wiring, be sure to the instrument power supply is OFF.
zDo not supply the AC power until complete the installation. This instrument does not have power
switch (ON/OFF).
zDo not fell or make a strong impact on this instrument rear panel terminal block because it is made
of resin.
zStriped electrical cable tip length is 6 mm.
zThe tightening torque of terminal screws on the terminal block is 0.5～0.6 N･m.
zCables which connecting this instrument isolate from noise sources, for example, power supply line
and I/O for control's as much as possible.
zBe sure to connect the ground wire must be D single ground. Do not common the ground with a
kind of power supply.
zFor CC-Link cable connection, use twist pear cable wire with shield (Cable for CC-link) and connect
the shield in terminal block's SLD terminal or F.G.terminal.
•Connect the termination to the CC-Link connector to electrical termination which is far from PLC as possible.
•Use the connecting cable for CC-Link.
•Refer to the “Construction and specification of network system” from the latest version of CC-Link Cable Wiring Manual
published by CC-Link Partner Association about communication speed and cable length
4
4．Setting of CC-Link connecting
Please set the following when you use CC-LINK interface.
4-1.Changeover of CC-Link communication setting change screen
Change from the standard measurement mode to the function mode by the following operations.
1) Touch the MENU key.
2) Touch the NEXT key.
3) Touch the OPTION key.
4) Touch the CC-LINK setting key.
4-2.Items of CC-Link setting
（1） The number of occupied stations.
Number of occupied stations is set.
Selectable from [1 station], [2stations], [4 stations].
Default has set as [4 stations].
（2） Setting of the stations
Execute the setting of the station No.
When 1 station is occupied : selectable from station No.01 to 64.
When 2 stations are occupied : selectable from station No.01 to 63
When 4 stations are occupied : selectable from station No.01 to 61.
The occupied station of this instrument is 1., 2, 4 stations.
※When 2 stations are occupied,and station No. is set as “01”,01 to 02 stations are occupied.
※When 4 stations are occupied,and station No. is set as “01”,01 to 04 stations are occupied.
Therefore, the station number must not overlap.
Default has selected [01].
（3） Setting of baud rate
Communication speed (unit: bps) is set.
Selectable from [156k], [625k], [2.5M], [5M] or [10M].
Default has set as [156k].
•Setting changes for occupied stations No. is corresponding to this software after ROM Ver.1.300.Before ROM Ver.1.200 is 4
station occupied station No.
5
（4） Data display method of 32 bit
32 bits data indication method is set.
Selectable from [Expression of standard binary] or [Sign in MSB].
Default has set as [Expression of standard binary].
Load value 32 bits data expression method Upper 16 bit Lower 16 bit
-1
Expression of standard binary FFFFH FFFFH
Sign in MSB 8000H 0001H
-10
Expression of standard binary FFFFH FFF6H
Sign in MSB 8000H 000AH
-99999
Expression of standard binary FFFEH 7961H
Sign in MSB 8001H 869FH
•Setting value becomes effective at restarting the power supply. Please restart the power supply after the changes.
Table des matières
Autres manuels Minebea Écran tactile
Manuels Écran tactile populaires d'autres marques
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manuel utilisateur
YASKAWA
YASKAWA TP 610C Manuel utilisateur
B&R
B&R Power Panel C Series Manuel utilisateur
Beijer Electronics
Beijer Electronics X2 control Manuel utilisateur
AXIOMTEK
AXIOMTEK GOT321W-521 Manuel utilisateur
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manuel utilisateur
