Mindray BeneView T5 Manuel utilisateur

BeneView T5/T6/T8/T9

Patient Monitor Quick Guide

Content in this guide is subject to change without prior notice.

Thank you for purchasing Mindray Patient Monitor.

We have included this convenient Quick Guide to help you with the basic operations. For

more details , please refer to the Operator’s Manual.

Note:

Before attempting to install, operate or adjust this product, please save and read the

Quick Guide completely.

This manual is based on the maximum conguration and therefore some contents may

not apply to your monitor. If you have any question, please contact us.



0123

Comply with the requirements of the

Council Directive 93/42/EEC.

Product Overview

Front View 1. Handle(T5 only)

2. Alarm lamp

When a physiological alarm or technical alarm occurs, this lamp will

ash as dened below.

High level alarms: the lamp quickly ashes red.

Meidum level alarms: the lamp slowly ashes yellow.

Low level physiological alarms: the lamp turns yellow without ashing.

Low level technical alarms: the lamp does not light.

3. Technical alarm lamp

This lamp will turn blue when a technical alarm occurs.

4. Display Screen

5. Power On/Off Switch

Press the switch to turn on the patient monitor. Press it again and hold

for 2 seconds to turn the patient monitor off. An indicator is built in this

switch. It turns on when the patient monitor is on and turns off when

the patient monitor is off.

6. AC power LED

It turns on when AC power is connected.

7. Battery LED

On: when the battery is being charged or already fully charged.

Off: when no battery is installed or noAC source is connected.

Flash: when the patient monitor operates on battery power.

8. press to silence all alarm sounds.

9. press to pause or restore alarms.

10. press to freeze or unfreeze waveforms.

11. press to start or stop recordings.

12. press to start or stop NIBP measurements.

13. If no menu is displayed on the screen, pressing it will enter the

main menu.

If there is a menu displayed on the screen, pressing it will close that

menu.

14. Knob



5 6 7

8 9 10 11 12 13 14

Product Overview

Side View (T5)

Bottom View (T6, T8, T9)

1. Compartment for CF storage card slot

2. Recorder

3. Battery compartment

4. Integral Module Racks

5. Integral Module Racks

Side View (T6, T8, T9)

5 2 9

Radiator

Product Overview

Rear View (T6, T8, T9)Rear View (T5)

34568

2 7

Product Overview

1. AC Power Input

2. USB Connectors

They connect such devices as the USB mouse, USB

keyboard, etc.

3. Nurse Call Connector

It connects the patient monitor to the hospital’s nurse call system

through the nurse call cable (PN: 8000-21-10361). Alarms

indications are alerted to nurses through the nurse call system, if

congured to do so.

4. Micro-D Connector

It outputs ECG, IBP and defibrillator synchronization signals

simultaneously.

5. Network Connector

It is a standard RJ45 connector that connects the patient

monitor to the CMS or other devices through the LAN.

6. iView Network Connector

It is a standard RJ45 connector that connects the iView system to

external network.

7. USB connector

They connect the controlling devices (USB mouse and USB

keyboard) of the secondary display.

8. Digital Video Interface (DVI)

It connects a standard digital video display.

9. SMR Connector

It connects the satellite module rack (SMR).

10. USB Connectors

They are only used for iView maintenance and data transfer.

11. Equipotential Grouding Terminal

When the patient monitor and other devices are to be used

together, their equipotential grounding terminals should

be connected together, eliminating the potential difference

between them.

Satellite Module Rack

Contact Indicator

SMR connector

Handle

As shown in the figure above, there is an indicator telling the

status of the SMR:

On: when the SMR works normally.

Off:

when the SMR disconnects from the patient monitor, there is a

problem with the power, or the patient monitor shuts down.

The SMR can be connected to the patient monitor through their

SMR connectors via a SMR cable.

Slot

The patient monitor supports the following modules:

Modules

BeneView T1: Used as a multi-measurement module for monitoring ECG, respiration, SpO2, temperature, NIBP and IBP.

MPM: Multi-parameter module. It can simultaneously monitor ECG, respiration, SpO2, temperature, NIBP and IBP.

IBP module: Invasive blood pressure module.

PiCCO: PiCCO module.

C.O. module: Cardiac output module.

CCO/SvO2module: CCO/SvO2interface module, used to interface with Edwards Vigilance II®or VigileoTM monitor.

NMT module: Neuromuscular transmission module.

SpO2module: Pulse oxygen saturation module.

BIS module: Bispectral index module.

RM module: Respiration mechanics module.

AG module: Anesthesia gas module. The functions of the O2and BIS modules can be incorporated into it.

CO2module: Carbon dioxide module (including sidestream, microstream and mainstream).

ScvO2 module: Central venous oxygen saturation module.

EEG module: Electroencephalograph module.

ICG module: Impedance cardiography module.

BeneLink module: BeneLink module is used for transmitting information from a connected external device to the monitor.

Basic Operations

Display Screen

1 2 34

Patient Information Area

Alarm Symbols

Technical Alarm Area

4. Physiological Alarm Area

5. Waveform Area

6. Parameter Area A

7. Parameter Area B

8. Prompt Message Area

9. QuickKeys area

Selectscreenitemsbypressingthemdirect-

ly on the patient monitor’s screen. You can

enable or disable touchscreen operation

by pressing and holding the [Main Menu]

QuickKey for 3 seconds. A padlock symbol

is displayed if touchscreen operation is

disabled.

Using the Touchscreen

Basic Operations

Setting the Screen

You can enter the [Screen Setup] window as shown below by selecting the [Screen Setup] button in the prompt

message area. In this window, you can allocate the positions of the parameters and waveforms. The parameters or waveforms

whose positions are not allocated will not be displayed.

Area A

Area B

Area C

The ECG parameter and the rst ECG waveform always display in

the rst row. The congurable areas can be classied as Area A,

Area B, and Area C.

In Area A, you can choose to display the parameters (having

waveforms) and their waveforms. Each parameter and the

associated waveform are displayed in the same row.

In Area B, you can choose to display the parameters and their

waveforms. When there is no parameter displayed in area C, both

the parameters and their waveforms will be displayed in area B.

Otherwise, only the parameters will be displayed.

In Area C, you can choose to display Timer and all the parameters

whose associated waveforms will not be displayed.

The screen can automatically adjust to ensure the best view based

on your screen setup.

If no corresponding parameter or waveform is displayed after the

module is inserted, you should perform the following inspections:

Check the connection between the module and lead, cable,

sensor, or external device.

Check whether there are the [The display setup for XX is

disabled] message and the ashing [Screen Setup] button

in the prompt message area. If yes, select this button to enter the

[Screen Setup] window for the desired display conguration.

Check that the parameter is switched on in the [Parameters

Switch] window.



Note:

The parameters whose positionsarenot allocatedinthe[Screen

Setup] window will not be displayed. However, the monitor can

still give alarms of these parameters.



Using the Main Menu

To enter the main menu, select the QuickKey on the monitor’s screen or the hardkey on the monitor’s front. Most of

monitor operations and settings can be performed through the main menu.

Basic Operations

Other menus are similar to the main menu

and contain the following parts:

Heading: gives a sum-up for the current

menu.

Main body: displays options, buttons,

prompt messages, etc. The menu

button with “>>’’ enlarges a secondary

window to reveal more options or

information.

Online help area: displays help

information for the screen item that the

cursor is positioned.

Select to exit the current menu.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mindray Moniteur

Mindray

Mindray Accutor 7 Manuel utilisateur

Mindray

Mindray BeneVision TM80 Manuel utilisateur

Mindray

Mindray iPM-9800 Manuel utilisateur

Mindray

Mindray BeneVision N1 Manuel utilisateur

Mindray

Mindray iMEC15S Manuel utilisateur

Mindray

Mindray uMEC10 Manuel utilisateur

Mindray

Mindray BeneVision N22 Manuel utilisateur

Mindray

Mindray VS-900 Manuel utilisateur

Mindray

Mindray VS8 Manuel utilisateur

Mindray

Mindray BeneView T1 Manuel utilisateur

Mindray

Mindray BeneVision TM80 Manuel utilisateur

Mindray

Mindray EPA001 Manuel utilisateur

Mindray

Mindray iPM-9800 Manuel utilisateur

Mindray

Mindray MEC-1000 Manuel utilisateur

Mindray

Mindray iPM Series Manuel utilisateur

Mindray

Mindray VS-800 Manuel utilisateur

Mindray

Mindray BeneVision N22 Manuel utilisateur

Mindray

Mindray BeneVision TM80 Manuel utilisateur

Mindray

Mindray BeneView T8 Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation