Milltronics InterRanger IR-200 Manuel utilisateur
InterRanger IR-200
Technology based. Customer driven.
January 1998
Instruction Manual
PL-545
33455450
Rev 1.0
hank you for purchasing Milltronics products. We endeavour to design
equipment that is simple to use and reliable in its operation, with the aim of
satisfying our customers' needs.
Milltronics has been designing and manufacturing process equipment since 1954.
Our fields of expertise include ultrasonic and capacitance level measurement ,
in-line weighing of dry bulk solids and motion sensing.
Milltronics is established world wide through associate offices and representatives.
Our network is continually being refined to provide our customers with first rate
sales information, engineering assistance and after sales support.
For more details on our products and service, please contact us and we will
provide you with a listing of the offices or representatives nearest you.
T
PL-545 3 InterRanger IR-200
TABLE OF CONTENTS
Specifications 3
Equipment 5
Component Descriptions 5
Storage 10
Maintenance 10
Principles of Operation 11
General 11
Dead Zones (Blanking Distances) 11
Hardware Installation 13
External Connections 13
IR-200 Monitor 14
IRT-100 series Sensor 14
IRP-8D Transceiver 14
Quick Start 15
Configuring the Unit 15
Determining Tank Depth 16
Operation 19
RUN Mode 19
Graphs 19
Program Mode 21
Parameters 23
Program Mode 23
Test Mode 29
Security “Lockout” for PGM and TEST Modes 30
Drawings are referenced throughout this manual. All referenced drawings are located at the end of the
manual.
ALSO CONTAINED IN THIS MANUAL
IR-200 Communication Protocol 31
InterRanger Profiling Software 49
InterRanger IR-200 4 PL-545
SPECIFICATIONS
Power »Requirements
»115/230Vac, ± 15%, 50/60 Hz
»Usage
»30W (+50W with optional heater)
»Protection
»2 – 2A 230Vac fuses
Maximum number of
Sensors »1
Range »0.3m (1 ft) to 30m (99 ft)
Accuracy »0.03m (0.1 ft) @ 7.5m (25 ft)
»0.06m (0.2 ft) @ 15m (50 ft)
»0.09m (0.3 ft) @ 22.5m (75 ft)
»0.12m (0.4 ft) @ 30.5m (100 ft)
Stability »0.1% per degree C
Operating
Temperatures »Sensor (standard)
»-30°C to 80°C (-22°F to 176°F)
»Sensor (high-temperature)
»-30°C to 105°C (-22°F to 221°F)
»Monitor (standard)
»-10°C to 50°C (14°F to 122°F)
»Monitor (with optional heater)
»-30°C to 50°C (-22°F to 122°F)
Humidity »Monitor
»5 to 100%, non-condensing
Outputs »4-20 mA, scalable to any range, 900 :max. load
»4 Programmable relays, rated to 7A @ 250Vac
»1 Alarm relay with panel light
Enclosure »Suitable for outdoor (Type 4X / NEMA 4X / IP65 enclosure)
PL-545 5 InterRanger IR-200
EQUIPMENT
Components in a typical InterRanger installation are:
Required
All of these components are needed for interface detection.
»Model IR-200 Monitor
»Model IRP-8D Transceiver Pre-Amp
»One of the Model IRT-100 series of Sensors
Customer-Supplied
These components are required to install the InterRanger Sensor correctly.
»3/4” stainless steel or galvanized conduit
»3/4” pipe coupling
Optional
These components are available from Milltronics:
Mounting: »Rail mount for Monitor
»Rail mount for Transceiver
»Stationary Handrail Bracket Kit for Sensor
»Swing-out Adapter Kit for Sensor
Heating: »Heater for Monitor
Communications:
»Profiling Software
»RS232 to RS485 Optically Isolated Converter
»RS-485 Repeater
»DB9M to DB25F Converter
COMPONENT DESCRIPTIONS
The InterRanger is made up of three main components: the Monitor, the Transceiver, and the Sensor.
The Monitor
displays the current interface level and transmits this information to other equipment.
The Transceiver
drives the ultrasonic Sensor and transmits the echo signals to the Monitor.
The Sensor
sends out the ultrasonic pulses through the liquid medium and receives the echoes.
InterRanger IR-200 6 PL-545
IR-200 MONITOR
Description
The Monitor is housed in a fiberglass NEMA 4X enclosure
containing the signal analysis, display, and control circuitry
for the system. All configuration and parameter changes are
made from the membrane keypad on the front panel of the
Monitor.
Temperature Range
-10°C to 50°C (14°F to 122°F)
-30°C to 50°C (-22°F to 122°F) with optional heater
Drawing
0-8130003Z-DU-C
HEATER FOR MONITOR
Description
The optional heater should be ordered when the Monitor is to
be located in a climate that drops below -10°C (14°F). The
heater has a built in thermostat so that power consumption is
kept to a minimum. When operating, the heater will consume
an additional 50 watts of power and is available in 115Vac
and 230Vac configurations.
IRP-8D TRANSCEIVER
Description
The Transceiver is housed in a polycarbonate NEMA 4X
enclosure and boosts the Sensor signal enabling it to be
transmitted over standard signal cable for up to 225 m (750’).
For use with the IRT-100D or IRT-100DC Sensor.
Temperature Range
-30°C to 50°C (-22°F to 122°F)
Drawing:
0-8130007Z-DU-B
PL-545 7 InterRanger IR-200
IRT-100D SENSOR
Description
A small, submersible, dual head Sensor constructed of
polyurethane and 316 stainless steel. It is fitted with a 3/4”
NPT nipple and includes 7.5 m (25’) of shielded cable
(optional 22.5 m (75’) available).
Temperature Range
-30°C to 80°C (-22°F to 176°F)
Drawing
0-8140001Z-DU-C
IRT-100DC SENSOR
Description
Same as the IRT-100D but is constructed of high
temperature epoxy. Supplied with either a Kynar®or 316
stainless steel 3/4” NPT nipple and 7.5 m (25’) of Teflon®
jacketed cable (optional 22.5 m (75’) available).
Temperature Range
-30°C to 105°C (-22°F to 221°F)
Drawing
0-8140002Z-DU-C
InterRanger IR-200 8 PL-545
RAIL MOUNT FOR MONITOR
Description
This anodized aluminum plate allows the Monitor to be mounted on a horizontal or vertical, standard 2” hand
rail. Two 2” U-bolts are supplied and all holes are pre-drilled.
Drawing
0-8130004Z-DU-C
RAIL MOUNT FOR TRANSCEIVER
Description
This anodized aluminum plate allows the Transceiver to be mounted on a horizontal or vertical, standard 2”
hand rail. Two U-bolts are supplied and all holes are pre-drilled.
Drawing:
0-8130008Z-DU-C
Anodized Aluminum Plate
2” Hand Rail
Anodized Aluminum Plate
2” Hand Rail
PL-545 9 InterRanger IR-200
STATIONARY HANDRAIL BRACKET KIT FOR SENSOR
Description
This kit contains a two piece mounting bracket, two 2” U-bolts and two 3/4” U-bolts for suspending an IRT-100
series Sensor from a standard 2” handrail. The 3/4” pipe and coupling needed to connect the Sensor to the
bracket are supplied by the customer.
Drawing
0-8140004Z-DD-C
SWING OUT ADAPTOR KIT FOR SENSOR
Description
This kit contains a swing-out bracket, a skimmer
guard, and six 3/4” U-bolts for use with an IRT-
100 series Sensor and Stationary Handrail
Bracket. This kit should be used if the tank has a
surface skimmer so that the Sensor deflects out
of the way when the skimmer moves past it.
Drawing
0-8140005Z-DD-C
Skimmer
InterRanger IR-200 10 PL-545
STORAGE
All components can be stored in a dry area with a maintained temperature range of -20°C to 50°C
(-4°F to 122°F). The Monitor and Transceiver should be sealed to prevent moisture intrusion in humid areas.
MAINTENANCE
The only part of the InterRanger IR-200 that requires maintenance is the Sensor face and only when it is
subject to algae or scale build-up.
Cleaning of the Sensor face is required is if build up of material exceeds:
»algae or debris: >1.5 cm (1/2”)
»scaling: >0.75 cm (1/4”)
Greater build-ups than these will make it difficult for the Sensor to detect the return echo signal and may result
in incorrect or null readings. The timing of this maintenance is determined by the rate of accumulation and
should be estimated at the installation site.
There is no routine maintenance or calibration procedures that need to be performed on the IR-200
electronics.
Table des matières
Autres manuels Milltronics Moniteur
