Miller SGA 100 Manuel utilisateur

Owner’s Manual

SGA 100 And SGA 100C

2012 MILLER Electric Mfg. Co.

2012−03 FORM: OM-190 753L

Use above FORM number when ordering extra manuals.

1. Safety Symbol Definitions

DANGER! −Indicates a hazardous situation which, if not

avoided, will result in death or serious injury. The possible

hazards are shown in the adjoining symbols or explained

in the text.

Beware of electric shock from welding electrode or wiring.

Touching the electrode while in contact with the work or

ground can cause electric shock. Always wear dry

gloves. Keep all panels and covers closed.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible ha-

zards are shown in the adjoining symbols or explained in

the text.

Hot parts can cause burns. Welding makes parts very hot

−let them cool before touching.

NOTICE Indicates statements not related to personal injury.

Indicates special instructions.

Wear safety glasses with side shields.

Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in

some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)

This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm.

Wash hands after use.

.The SGA 100 and SGA 100C are not required for use with the Millermatic 185, Millermatic 210, and IronMan 210 models, and IronMan 250 models

effective with serial no. LA135884 and following).

2. Weld Control Specifications

Specification

Input Power Single-Phase 115 Volts AC, .5 Amperes, 60 Hertz

Control Circuit Voltage Provided To Spool Gun 36 Volts DC

Welding Power Source Type Constant Voltage (CV) DC, With or Without Contactor

Connections Gun Trigger Controls, Gas And Weld Cables

Welding Process DC Gas Metal Arc Welding (GMAW)

Input Power Cord With Plug 10 ft (3 m)

Overall Dimensions SGA 100: 13 in. (330 mm) L x 8 in. (203 mm) W x 5 in. (127 mm) H

SGA 100C: 13 in. (330 mm) L x 8 in. (203 mm) W x 9 in. (229 mm) H

Weight SGA 100: 10 lb (4.5 kg); SGA 100 C: 13 lb (5.9 kg)

3. Duty Cycle

Maximum rating for the SGA 100

and SGA 100C is 150 amperes at a

60% duty cycle.

Duty Cycle is percentage of 10 min-

utes that unit can weld at rated load

without overheating.

NOTICE −Exceeding duty cycle

can damage unit and void warranty.

6 Minutes Welding 4 Minutes Resting

.If you are connecting this spoolgun adapter to a unit with an output contactor, proceed to Section 4. If you are connecting this spoolgun adapter

to a unit without an output contactor, proceed to Section 5.

OM-190 753 Page 2

4. Installing SGA 100 Spoolmate Adapter (Kit 043 856)

A. Making Connections To Units With An Output Contactor (Millermatic 185, Millermatic 210, And IronMan

210 Models, And IronMan 250 Models Effective With Serial No. LA135884 And Following Do Not Require

This Accessory)

Ref. 802 181

!Turn Off and disconnect input

power.

1 Spoolmate Spoolgun

2 SGA 100 Control Box

3 Welding Power Source With 1/2 in.

(13 mm) Weld Cable Stud

4 1/2 in. (13 mm) Weld Cable Stud

5 Front Panel

6 Front Panel Opening

7 Spoolgun Weld Cable

Route Spoolgun weld cable through front

panel opening and connect to 1/2 in. (13

mm) weld cable stud. NOTE: if unit does

not have a 1/2 in. (13 mm) weld cable stud,

proceed to Section 3B

8 Interconnecting Cord

Connect interconnecting cord as shown.

NOTE: a second interconnecting cord with

female friction terminals on each end (not

shown) is provided with this kit. If your unit

requires this type of interconnecting cord

for trigger operation, connect female

friction terminals to matching male friction

terminals on welding power source and

SGA 100 control box. Polarity is not

important.

9 Spoolgun Gas Hose

Slide spoolgun gas hose onto barbed fitting

on SGA 100 control box where shown.

10 Spoolgun Trigger Control Plug

Connect spoolgun trigger control plug to

matching receptacle on SGA 100 control

box where shown.

11 Gas Hose

Slide gas hose onto fitting on back of SGA

100 control box.

12 115 VAC Plug

Connect plug as shown.

Tools Needed:

3/4 in.

.Drawing shows typical welding

power source installation.

.Loosen and raise drive tension arm

on power source wire feeder, and

turn off mild steel shielding gas

supply when using spool gun.

.100% argon shielding gas

required for aluminum.

OM-190 753 Page 3

B. Connecting Spoolmate Spoolgun Weld Cable To Units Without A 1/2 in. Weld Cable Stud

Ref. 802 181

1 Wire Drive Assembly

2 Gun Securing Bolt

3 Gun Securing Nut

Remove gun securing nut.

4 Terminal

Slide terminal onto gun securing bolt

and secure with gun securing nut.

5 Spoolgun Weld Cable Ring

Terminal

Cut off ring terminal and strip

insulation back 1/2 in. (13 mm).

Slide spoolgun weld cable into

terminal 1/2 in. (13 mm). Tighten

set-screw.

Go back to Section 3A, Item 8, to

complete the installation.

Tools Needed:

5/16 in.

1/2 in.

.Drawing shows typical welding

power source installation.

OM-190 753 Page 4

5. Installing SGA 100C Spoolmate Adapter w/ Contactor (Kit 043 857)

A. Making Connections To Units Without An Output Contactor

802 188

!Turn Off and disconnect input

power or shut off engine.

1 Welding Generator

2 Weld Cable (Customer Supplied)

3 Spoolmate Spoolgun

4 Spoolgun Weld Cable

5 SGA 100C Control Box

Proceed to Section 4B

6 Spoolgun Gas Hose

Slide spoolgun gas hose onto barbed

fitting on SGA 100C control box where

shown.

7 Spoolgun Trigger Control Plug

Connect spoolgun trigger control plug

to matching receptacle on SGA 100C

control box where shown.

8 Gas Hose

Slide gas hose onto fitting on back of

SGA 100C control box.

9 115 VAC Plug

Connect plug to 115 volt power supply.

.Drawing shows typical welding

power source installation.

OM-190 753 Page 5

B. Making Connections In The Contactor Control Box

Ref. 802 189-A

.The SGA 100C can be used

with MIG welding power

sources by simply following the

hookup procedure for an SGA

100.

1 SGA 100C Control Box

2 Contactor Box

Remove contactor box

3 Contactor Control Leads

4 Spoolgun Weld Cable Ring

Terminal

Cut off ring terminal and strip

insulation back 1/2 in. (13 mm).

5 Terminals

Slide spoolgun weld cable into

terminal 1/2 in. (13 mm). Tighten

set-screw.

6 Weld Cable

Strip insulation back 1/2 in.

(13 mm).

Slide weld cable into terminal 1/2 in.

(13 mm). Tighten set-screw.

Install contactor box back onto

SGA 100C control box.

Go back to Section 4A, Item 6 to

complete this installation.

Tools Needed:

1/2 in.

3/8 in.

Model Wire Size / Type Metal Size Wire Feed Speed Setting Voltage %

SGA 100 w/3035 spool

gun on Millermatic 135 .030 / 4043

14 ga aluminum 25 −30 65 −85

1/8 in. aluminum 25 −30 100

3/16 in. aluminum — —

1/4 in. aluminum — —

SGA 100 w/3035 spool

gun on Millermatic 135 .035 / 4043

14 ga aluminum 25 −30 80 −100

1/8 in. aluminum 25 −30 100

3/16 in. aluminum — —

1/4 in. aluminum — —

SGA 100 w/3035 spool

gun on Millermatic 175 .030 / 4043

14 ga aluminum 35 −40 35 −40

1/8 in. aluminum 45 −50 45 −50

3/16 in. aluminum 50 −55 80 −100

1/4 in. aluminum 50 −55 80 −100

SGA 100 w/3035 spool

gun on Millermatic 175 .035 / 4043

14 ga aluminum 28 −32 35 −40

1/8 in. aluminum 38 −42 45 −50

3/16 in. aluminum 40 −45 100

1/4 in. aluminum 40 −45 100

.These values are starting parameters only. When welding aluminum use 100% argon shielding gas, maintain a 1/2 to 3/4 in. tip to work distance,

and a 10 to 15 degree push angle with the spool gun.

OM-190 753 Page 6

6. Electrical Diagram

206 578

Figure 6-1. Circuit Diagram

OM-190 753 Page 7

Notes

OM-190 753 Page 8

7. Parts

Figure 7-1. Main Assembly

802 302-A

1415

OM-190 753 Page 9

Description

Part

No.

uantity

Kit

043856

SGA 100 Spoolmate Adapter Kit 043 856 Or

SGA 100C Spoolmate Adapter w/Contactor Kit 043 857

043857

1 057 357 BUSHING, snap-in nyl .937 ID x 1.125 mtg hole 2...... ............. ......................

2 190 421 COVER, ext contactor 1...... ............. .............................................

3 190 418 HANDLE 1...... ............. ........................................................

4 131 515 LABEL, warning electric shock 1 1...... ............. ........................... ........

5 252 907 W CONTACTOR, def prp 60A 3P 120 VAC coil 1...... ....... .. ..........................

6 206 951 T1 XFMR, control 115V pri 35V/24V sec 1 1...... ....... .. ..................... ........

7 170 970 GS1 VALVE, 115 VAC 2way 2 pipes 6mm 60 Hz 1 1...... ..... .. ................ ........

8 195 531 CB1 CIRCUIT BREAKER, man reset 1P 2.5A 250V 1 1...... ..... .. ............ ........

9 206 960 CABLE, power 1 1...... ............. ........................................ ........

10 114 050 R2 RESISTOR, ww fxd 10W 1K ohm 1 1..... ....... .. ........................ ........

11 072 817 CR1 RELAY, encl 24 VAC DPDT 20A/120 VAC 8 pin fla 1 1..... ..... .. ......... ........

12 048 282 RC2 RECEPTACLE w/skts 1 1..... ..... .. .................................. ........

13 134 201 STAND-OFF SUPPORT, pc card 4 4..... ............. ........................ ........

14 191 345 FOOT, mtg snap-in vinyl 3 3..... ............. ................................ ........

15 184 734 BUSHING, terminal 2 position 1 1..... ............. ........................... ........

16 172 171 FTG, hose brs barbed coupler 1 1..... ............. ........................... ........

17 097 924 KNOB pointer 1.625 dia 1 1..... ............. ................................ ........

18 206 815 NAMEPLATE 1..... ............. .........................................

18 206 816 NAMEPLATE 1..... ............. ....................................................

19 206 949 BASE 1 1..... ............. ................................................ ........

20 198 087 R1 POT, CP std slot 1T 2W 1K ohm 1 1..... ....... .. ......................... ........

21 240 157 PC1 CIRCUIT CARD ASSY, motor 1 1..... ..... .. ........................... ........

22 190 420 WRAPPER 1 1..... ............. ........................................... ........

23 025 338 BUSHING, nyl univ 23/32 hd dia .625 mtg hole 1..... ............. .......................

23 024 376 BLANK, snap-in nyl 1..... ............. ....................................

24 191 103 LUG, univ w/scr 600V 1 2..... ............. .................................. ........

190 681 CABLE, interconnecting 6 ft trigger fric to fric 1 1........ ............. .............. ........

190 682 CABLE, interconnecting 6 ft trigger (amp) 4 pin to fric 1 1........ ............. ....... ........

183 581 HOSE, gas 1 1........ ............. ........................................... ........

OM-190 753 Page 10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Miller Système de soudage

Miller

Miller Big Blue 800 X Duo Air Pak Manuel utilisateur

Miller

Miller PipePro 304 Manuel utilisateur

Miller

Miller Millermatic Pulser M-15 Gun Manuel utilisateur

Miller

Miller Bobcat 200 Air Pak Manuel utilisateur

Miller

Miller TRUE BLUE MigMatic 260i Manuel utilisateur

Miller

Miller STH 160 Manuel utilisateur

Miller

Miller GOLDSTAR 302 Manuel utilisateur

Miller

Miller Maxstar 200 Manuel utilisateur

Miller

Miller Bobcat 225 Manuel utilisateur

Miller

Miller INVISION 350 MPa AUTO-LINE Manuel utilisateur

Miller

Miller Syncrowave 250 DX Manuel utilisateur

Miller

Miller Gold Seal GS-250 Manuel utilisateur

Miller

Miller Millermatic 140 Manuel utilisateur

Miller

Miller Dimension NT 450 Manuel utilisateur

Miller

Miller HJ134589 Manuel utilisateur

Miller

Miller Millermatic 212 Auto-Set Manuel utilisateur

Miller

Miller INFINITY 35 Manuel utilisateur

Miller

Miller SQUAREWAVE 1000 Manuel utilisateur

Miller

Miller Bobcat 250 Manuel utilisateur

Miller

Miller SUBARC DRIVE 100 CE Manuel utilisateur

Miller

Miller XR Python 25 Ft. Manuel utilisateur

Miller

Miller Big Blue 400P Manuel utilisateur

Miller

Miller Shielded Metal Arc Welding Mode d’emploi

Miller

Miller XR-Aluma-Pro 15W Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur