Miller Dynasty 210 DX Manuel utilisateur

OWNER’S MANUAL

OM-267 827C 2015−05

Dynasty210 DX and 280 DX

AC Independent Expansion

Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.

Read the safety information at the beginning of the manual and in each section.

1-1. Software Expansion

.A software update is required to ensure proper

operation of all purchased feature expan-

sions. For instructions to download TIG Soft-

ware updates, see PDF file F269272A on soft-

ware expansion memory card.

Card Requirements:

.Purchased software expansion memory card

required.

1 Memory Card Port

2 Indicator LED

Enabling Software Expansion:

Insert card containing software expansion into

port.

LED indicator blinks green while machine is read-

ing from or writing to the card. After successfully

readingfrom or writing to the card, the LED switch-

es from blinking green to continuous green. The

machineis now ready to use software expansion.

Do not remove card while LED is blinking green.

.Software expansion card must remain in memory

card port to enable software expansion.

Disabling Software Expansion:

Remove the software expansion card from the

memorycard port.

Troubleshooting:

Problem: Indicator LED is continuous red.

Remedy: Remove and reinsert card. If problem

continues,the card is bad. Contact Factory Autho-

rized Service Center for a replacement card.

The memory card port uses an SD memory card.

The SD Logo is a trademark of the SD-3C LLC

Company.

OM−267 827 Page 2

1-2. AC Independent Amplitude (Dynasty DX Models Only)

1 AC Waveshape Control

Press switch pad until desired function is select-

ed.

2 Encoder Control (Set Value)

3 Ammeter (Displays Value)

4 Voltmeter (Parameter Selection)

EN Amperage [EN] -Use with AC TIG only to se-

lect electrode negative amperage value.

EP Amperage [EP] -Use with AC TIG only to se-

lect electrode positive amperage value.

.Both Balance and AC Frequency LEDs light

wheneither EN or EP Amperage is selected.

5 AmperageControl

Average Amperage Control: Setting EN Am-

perage,EP Amperage, Balance, and Frequency

values creates an average amperage. The oper-

ator can change the average amperage value

whilemaintaining the same EN amperage to EP

amperageratio at the existing balance and fre-

quency. To change the average amperage value,

press the Amperage switch pad and turn the En-

coder control. The changing average value is dis-

playedon the ammeter. Example: If EN Amper-

age is 150, EP Amperage is 100, Balance is 75%,

and Frequency is 120, the average amperage is

138 amps. If you press the Amperage switch pad

and turn the Encoder control until 69 amps is dis-

played,the EN amperage is now 75 and EP am-

perageisnow 50. The balance remains 75%, and

the frequency is still 120, and the 1.5 to 1 EN am-

perageto EP amperage ratio is maintained.

150 A

1-3. AC Independent Waveshape (Dynasty DX Models Only)

.See Dynasty 210 DX and 280 DX Opera-

tion section in Owner’s Manual for addi-

tionalinformation on Accessing User Set-

up Menu. The [ACEN], [ACEP] option re-

places the [AC] option.

1 Amperage (A) Control

2 Gas/DIG Control

3 Parameter Display

Press Gas/DIG control until [ACEN] is dis-

played.Press the Amperage (A) control to tog-

gle between [ACEN] and [ACEP].

4 Setting Display

5 Encoder Control

Use Encoder to select between advanced

squarewave [ADVS], soft squarewave

[SOFT], sine wave [SINE], or triangle wave

[TRI]. The default is [SOFT].

345

USER

SOFT

ACEN

ACEP

Autres manuels pour Dynasty 210 DX

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Miller Système de soudage

Miller

Miller Gold Seal Model 440 Manuel utilisateur

Miller

Miller Continuum 500 Manuel utilisateur

Miller

Miller Millermatic 212 Auto-Set Manuel utilisateur

Miller

Miller Deltaweld 500 Manuel utilisateur

Miller

Miller Auto-Continuum 500 Manuel utilisateur

Miller

Miller Shielded Metal Arc Welding Mode d’emploi

Miller

Miller FieldPro Feeder CE Manuel utilisateur

Miller

Miller Maxstar 152 Manuel utilisateur

Miller

Miller LMSW-52 Manuel utilisateur

Miller

Miller Summit Arc 1000 Manuel utilisateur

Miller

Miller SuitCase 8VS X-TREME CE Manuel utilisateur

Miller

Miller Gold Seal 160 i Manuel utilisateur

Miller

Miller Big Blue 302D Manuel utilisateur

Miller

Miller XMT 300 CC Manuel utilisateur

Miller

Miller Spectrum 625 X-TREME Manuel utilisateur

Miller

Miller M-100 Manuel utilisateur

Miller

Miller RAD-400 Manuel utilisateur

Miller

Miller SQUAREWAVE 1000 Manuel utilisateur

Miller

Miller AC 150 Stick Manuel utilisateur

Miller

Miller RFCS-5 Manuel utilisateur

Miller

Miller CST 280 Manuel utilisateur

Miller

Miller MigMatic 300 Manuel utilisateur

Miller

Miller TRAILBLAZER 302 AIR PAK Manuel utilisateur

Miller

Miller Multimatic 220 AC/DC Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur