Miller Deltaweld 350 Manuel utilisateur

DANGER! − Indicates a hazardous situation which, if not

avoided, could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or explained in

the text.

Have only trained and qualied persons install, operate, or

service this unit. Read the safety information at the beginning

of these instructions and in each section. Call your distributor

if you do not understand the directions. For WELDING SAFETY

and EMF information, read owner’s manual(s).

Falling equipment can injure, and damage equipment. Never

put any body part under unit while lifting. Lifting forks must

extend out opposite side of base. Lift and support unit only

with proper equipment and correct procedures. Follow the

guidelines in the Applications Manual for the Revised NIOSH

Lifting Equation (Publication No. 94−110) when manually

lifting heavy parts or equipment.

Wear safety glasses with side shields.

Deltaweld®350 Quick Setup Guide

2 x 3/4 in.

1/2 in., 9/16 in., 3/4 in.

1. Getting Started

Ensure sufcient room exists behind assembly before

removing it from pallet.

Remove shrink wrap. Remove and unbox all packages from

the cart. Verify that all parts are present.

Wire feeder

Accessories kit includes weld cables, gas regulator,

gas hose, control cable, drive roll kit, and hardware kit.

Hardware kit includes gas bottle chain, 1/2 in. bolt,

and washer.

Bernard™MIG gun

2. Removing Integrated Cart From Pallet

Have only trained and qualied persons

install power cable and select input voltage.

See welding power source Owner’s Manual.

Do not connect power until assembly is complete.

See welding power source Owner’s Manual.

Remove the two lag bolts and two mounting brackets

from the rear of the cart. Remove the bolt from the

front underside of the cart.

Push cart backwards off the front and rear blocks.

When wheels and casters are on the pallet, slide rear

block out of the way. Continue to push cart backward

until wheels and casters are on the ground.

1/2 in.

Safety Symbol Denitions

Tools Needed

Scan this code or visit

MillerWelds.com/deltaweldsetup

to view a video of the Deltaweld 350

integrated cart setup.

MillerWelds.com

4. Installing MIG Gun, Cables, and Gas Cylinder

5. Setting Up Wire Feeder

Loosen knob on drive assembly.

Insert MIG gun into drive assembly.

Align Accu-Mate™with groove in gun and tighten knob.

Align MIG gun control plug with connector on feeder.

Push on and twist to tighten.

Align power source end of control cable to connector

on the front of the welding power source. Push on and

twist until it clicks. Route cable through hole in cart

base, then up through hole in gas cylinder upper

bracket, and underneath the spool support. Align

feeder end of cable with connector on the rear of

feeder. Push on and twist until it clicks.

Connect positive (+) weld cable (power source side) to

positive output stud. Route cable through hole in cart

base. Finish routing cable in the same manner as

control cable (5).

Connect negative (-) weld cable (power source side) to

negative output stud.

Secure gas cylinder with chain from hardware kit.

Gas regulator (see installation instructions in box)

Gas hose

Connect positive

(+)

weld cable (feeder side)

to connection point inside feeder. Tighten to

27–33 ft. lb. (36.6–45 N•m).

Push down knobs to open drive assembly.

Install drive rolls.

2 x 3/4 in.

9/16 in.

3. Attaching Wire Feeder To Integrated Cart

Do not leave wire feeder unattended until it is

secured to the cart.

Lock casters.

Remove wire feeder and wire feeder Owner’s Manual

from box. Discard packaging.

Obtain 1/2 in. bolt, washer, and spacer from

hardware kit.

Align hole under wire feeder spool support with post

on top of cart. Lower feeder onto post. Use 1/2 in.

bolt, washer, and spacer to secure feeder to post.

Tighten to 21 ft. lb. (28.5 N•m).

Remove pin (leave lanyard secured to back of cart

assembly) and insert through hole in feeder base into

post on top of the cart upper assembly.

Finishing Installation — See Owner’s Manual

for your specic wire feeder and welding

power source for information on connecting

input power and operating equipment.

3/4 in.

Table des matières

Autres manuels Miller Système de soudage

Miller

Miller PipePro XC Manuel utilisateur

Miller

Miller Spectrum 875 Auto-Line Manuel utilisateur

Miller

Miller MW225 Manuel utilisateur

Miller

Miller DIVERSION 165 And Manuel utilisateur

Miller

Miller Maxstar 210 Manuel utilisateur

Miller

Miller AXCESS E 450 CE Manuel utilisateur

Miller

Miller DC 253 Stick Manuel utilisateur

Miller

Miller DYNASTY 200 DX Manuel utilisateur

Miller

Miller D-74 MPa Plus Manuel utilisateur

Miller

Miller Gold Seal 422 Manuel utilisateur

Miller

Miller AUTO ARC TIG 50A Manuel utilisateur

Miller

Miller Blue Thunder 253 Manuel utilisateur

Miller

Miller SUBARC DRIVE 100 CE Manuel utilisateur

Miller

Miller TRAVEL MAASTER SPT-1C Manuel utilisateur

Miller

Miller AA40GB w/OCP Manuel utilisateur

Miller

Miller matic 250mp 1995 Manuel utilisateur

Miller

Miller Dynasty 400 Manuel utilisateur

Miller

Miller Spectrum 625 X-TREME Manuel utilisateur

Miller

Miller Syncrowave 250 DX Manuel utilisateur

Miller

Miller Dialarc 250 AC/DC Manuel utilisateur

Miller

Miller Big Blue 400 Eco Pro CC Manuel utilisateur

Miller

Miller Maxstar 150 STL Manuel utilisateur

Miller

Miller SP-1 Manuel utilisateur

Miller

Miller EnPak A60GBHW Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuel utilisateur