MilDef RB14 Manuel utilisateur

Workstation Computer

RB14

User’s Guide

○

Notice

The company reserves the right to revise this publication or to change its contents

without any notice. Information contained herein is for reference only and does not

constitute a commitment on the part of the manufacturer or any subsequent vendor.

They assume no responsibility or liability for any errors or inaccuracies that may

appear in this publication nor are they in anyway responsible for any loss or

damage resulting from the use (or misuse) of this publication.

Any of the software described in this manual is sold or licensed "as is". Should the

programs prove defective following purchase, the buyer (and not the manufacturer,

its distributor, or its dealer) assumes the entire cost of all necessary servicing,

repair and any incidental or consequential damages resulting from any software

defects.

Brand and product names mentioned in this publication may or may not be

copyrights and/or registered trademarks of their respective companies. They are

mentioned for identification purposes only and are not intended as an

endorsement of that product or its manufacturer.

Trademarks

All other brand and product names are trademarks or registered trademarks of

their respective companies.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

RF exposure warming

This equipment must be installed and operated in accordance with provided

instructions and antenna(s) used for this transmitter must be installed to

provide a separation distance of at least 20 cm from persons and must not be

co-located or operating in conjunction with any other antenna or transmitter.

End-users and installers must be provided with antenna installation

instructions and transmitter operating conditions for satisfying RF exposure

compliance.

Regulatory Information/ Disclaimers

Installation and use of this workstation must be in strict accordance with the

instructions included in the user documentation provided with the product. Any

changes or modifications (including the antennas) made to this device that are not

expressly approved by the manufacturer may void the user’s authority to operate

the equipment.

The manufacturer is not responsible for any radio or television interference caused

by unauthorized modification of this device, or the substitution of the connecting

cables and equipment other than manufacturer specified. It is the responsibility of

the user to correct any interference caused by such unauthorized modification,

substitution or attachment. Manufacturer and its authorized resellers or distributors

will assume no liability for any damage or violation of government regulations

arising from failing to comply with these guidelines.

III

Federal Communications Commission regulatory compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

The device has been tested in accordance to FCC regulation Part 15 Subpart B,

Subpart C, Subpart E and found the test results indeed meet the limitation of the

relevant test standard(s) listed below:

FCC 47 CFR Part 15 Subpart B (15.109/15.107)

FCC 47 CFR Part 15 Subpart C (2019)

FCC 47 CFR Part 15 Subpart E (2019)

Note:

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency

energy and if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

⚫Reorient or relocate the receiving antenna.

⚫Increase the separation between the equipment and receiver.

⚫Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

⚫Consult the dealer or an experienced radio/TV technician for help to assure

continued compliance, any changes or modifications not expressly approved

by the party responsible for compliance could void the user's authority to

operate this equipment. (Example - use only shielded interface cables when

connecting to computer or peripheral devices).

Important:

Changes or modifications to this product not authorized by MilDef could void the

electromagnetic compatibility (EMC) and wireless compliance and negate your

authority to operate the product.

In order to maintain compliance with FCC regulations, compliant peripheral

devices and shielded cables must be used with this equipment.

CE Declaration of Conformity

The device is hereby confirmed to comply with the requirements set out in the

Council Directive on the Approximation of the Laws of the Member States relating

to Electromagnetic Compatibility Directive (2014/30/EC) and Complies with the

essential requirements of Article 3 of the RED 2014/53/EC Directive, if used for its

intended use and that the following standards have been applied:

EN55032 Class B: 2015/A11:2020

EN55024 Class B: 2010/A1:2015

EN 62368-1 2014/ A11:2017

EN 300 328 V2.2.2 2019-07

EN 301 893 V2.1.1:2017-05

EN 303 413 V1.1.1:2017-06

EN 50332-2:2013

EN 301 489-1 V2.2.3 (2019-11)

EN 301 489-17 V3.1.1 (2017-02)

EN 301 489-19 V2.1.1 (2019-04)

EN62311 2008

Power Conservation

This workstation consumes less power compared to conventional consumer

workstations. The power consumption may be further reduced by properly

configuring the Power Management Setup.

It is recommended that the power saving features be enabled even when not

running on battery power. Power Management features can conserve power

without degrading system performance.

Power Safety

There are specific power requirements for your workstation:

⚫Only use an approved AC adapter designed for this workstation.

⚫There is a 3-prong grounded plug for the AC adapter. The 3rd prong is an

important mechanism for ensuring product safety. Please do not neglect

the importance of this mechanism. If you are unable to access a

compatible outlet, please hire a qualified electrician to install a compatible

outlet for you.

⚫When unplugging the AC power cord, please make sure to disconnect the

cord by pulling from the plug head instead of pulling from the wire to

prevent wire damage.

⚫Make sure the power outlet and any other extension cord(s) you use can

support the total current load of all the connected devices.

⚫Before cleaning the workstation, please make sure it is disconnected from

any external power source.

Warning

Before any upgrade procedures, make sure the power is turned off, and all

the cables are disconnected. Also, it is advisable to remove your battery to

prevent your workstation from accidentally turning on.

VII

Battery Precautions

⚫Only use batteries designed for this workstation. Using incompatible

battery types may cause explosion, leakage or damage to the workstation.

⚫Do not remove the battery from the workstation while the workstation is

powered on.

⚫Do not continuously use a battery that has been dropped, or that appears

damaged (e.g. bent or twisted) in any way. Even if the workstation is able

to continuously work with a damaged battery, the circuit damage may

occur and possibly cause fire.

⚫Always use the charger designed for this workstation to recharge the

battery. Incorrect recharging may cause the battery to explode.

⚫Do not try to repair a battery by yourself. For battery service or

replacement, please contact with your service representatives.

⚫Please dispose damaged battery promptly and carefully. Explosion or

leakage may occur, if the battery is improperly handled or discarded.

Notice:

For safety, charging will stop if the internal temperature of the battery is out of

range (<0°C; >50°C), while discharging stops if the internal temperature of the

battery is detected over 65°C. Please note that charging could have stopped

before the ambient temperature reaching these boundaries because the internal

temperature of the battery does not equal to the ambient temperature.

Battery Disposal & Caution:

The product that you have purchased contains a rechargeable battery.

The battery is recyclable. At the end of its service life, under various state

and local laws, it may be illegal to dispose of this battery into the

municipal waste stream. Check with your local solid waste officials for

details in your area for recycling options or proper disposal. Danger of

explosion may possibly occur, if the battery is incorrectly replaced.

Replace only with the same or the equivalent battery recommended by

the manufacturer. Discard the used battery according to the

manufacturer’s instructions.

VIII

Environmental Information, Material Safety & Recycling

All materials used in the manufacturing of this equipment are recyclable or

environmentally friendly. Please recycle the packing materials in accordance with

local regulations at the end of the product's service life.

Notice:

⚫The equipment may contain insignificant amount of hazardous

substances for health and environment below control level.

⚫To avoid spreading such substances into the eco system and to minimize

the pressure on the natural environment, you are encouraged to reuse or

recycle most of the materials in a safe way after an end of the product life.

⚫For more information on collection, reuse and recycle of materials, please

consult local or regional waste administrations for more information. You

can also contact your dealer for more information on the environmental

details of the equipment.

⚫The symbol of the crossed out wheeled bin indicates that the product

(electrical and electronic equipment) should not be placed in municipal

waste. Please check local regulations for disposal of electronic products.

 
 
TABLE OF CONTENTS 
 
TABLE OF CONTENTS................................................................9
CHAPTER ONE - GETTING STARTED......................................11
UNPACKING ...............................................................................................11
 QUICK OPERATION....................................................................................11
APPEARANCE OVERVIEW ............................................................................13
CHAPTER TWO - OPERATING INFORMATION .......................17
WORKPLACE..............................................................................................17
RUGGEDNESS............................................................................................17
WORKING WITH POWER BUTTON .................................................................18 
OPERATING SYSTEM ..................................................................................19 
BOOT UP AND POST..................................................................................19 
SHUT DOWN...............................................................................................21
SLEEP/HIBERNATE .....................................................................................21
TOUCHPAD ................................................................................................22
KEYBOARD ................................................................................................23 
LED INDICATORS .......................................................................................24
MANAGING SOLID STATE DRIVE (SSD)........................................................24 
RTC.........................................................................................................25
SYSTEM MANAGER.....................................................................................26
SETTING WAKE ON LAN.............................................................................29
USING KENSINGTON LOCK SLOT..................................................................30
INSTALLING HANDLE ...................................................................................31
INSTALLING SMART CARD READER (OPTION)................................................33
CHAPTER THREE - MANAGING POWER.................................34
AC ADAPTER.............................................................................................34
BATTERY...................................................................................................35 
BATTERY RECALIBRATION...........................................................................38
POWER CONSERVATION .............................................................................40
CHAPTER FOUR - BIOS SETUP...............................................42
MAIN MENU ...............................................................................................42
ADVANCED MENU.......................................................................................43 
CPU Configuration Sub-Menu......................................................................45 
PCH-FW Configuration Sub-Menu ...............................................................45 
Trusted Computing Sub-Menu.....................................................................46 
RF Device Control Sub-Menu.......................................................................46 
EC Thermal Control Sub-Menu ....................................................................47 
AC In Boot Control Sub-Menu......................................................................47 
USB Power Control Sub-Menu.....................................................................48 
Battery Recalibration Sub-Menu..................................................................48 
IT8786 Super IO Configuration Sub-Menu...................................................49 
Intel® BIOS Guard Technology Sub-Menu....................................................49 