Mighty Mule R4222 Manuel utilisateur

PHOTO BEAM

R4222

THROUGH BEAM

Mighty Mule, Linear and GTO are registered trademarks of Nortek Security & Control LLC.

www.nortekcontrol.com

Technical Support: (800) 421-1587

TABLE OF CONTENTS

Photoelectric Dual Beam Detector.................................... 3

Parts ............................................................... 3

Receiver Indicators.................................................... 3

Transmitter Indicators ................................................. 3

Mounting Cautions ................................................ 4

Mounting and Connections.......................................... 5

Wiring the R4222 Photo Eyes to Gate Operators............................. 7

Transmitter Terminal ................................................... 7

Receiver Terminal ..................................................... 7

Pole Mounting ....................................................... 8

Dip Setting ....................................................... 8

Beam Alignment .................................................. 9

Beam Interruption Time Adjustment .................................. 10

Verify Correct Operation ............................................ 10

Troubleshooting................................................... 11

Specications .................................................... 11

PHOTOELECTRIC DUAL BEAM DETECTOR

Cover

Receiver Wiring Terminals Transmitter Wiring Terminals

Internal View

Wiring Knockout

Connection Terminals

Indicator

Lens

Vertical

Alignment

Screw

Signal Level Display

Cover Locking Screw

Tamper

Parts



POWER HEATER TAMPER

COM

ALARM

NO 

POWER HEATER TAMPER

Receiver Indicators

• GOOD LED (Green). Use when adjusting

beam alignment. ON when beams are

aligned, OFF when beams are not aligned.

(Refer to operation instructions)

• LEVEL LED (Red). ON indicates received

signal. Brightness varies, depending on

incident level.

• ALARM LED (Red). ON indicates beam

blocked. Use when setting response time.

(Refer to operation instructions)

Transmitter Indicators

• POWER LED (green). ON when light

beam is transmitting.

MOUNTING CAUTIONS

Do not mount the detector in the following conditions:

Where obstructions (plants,

fences, etc.) are between the

receiver and the sender.

Where sunlight and headlights

shine directly into the front of

the receiver.

Where the mounting

surface is unstable.

MOUNTING AND CONNECTIONS

1. Loosen the cover holding screw, and

remove the outer cover.

2. Remove the rubber knockout, and use the

screw holes to mount the unit.

3. Remove the rubber knock-out, and pull the

wire through.

Wiring

Back Cover

4. Mount the detector on the wall.

5. Connect wires to the terminals:

See wiring diagram, next page.

• Wire with 22awg minimum

• 300 ft (91 .4m) max length

• Be sure to capture the wire ends under the

wire clamp plates.

• Avoid frayed ends on wires that might

produce a short circuit.

Correct Wrong Wrong



POWER HEATER TAMPER

COM

SAFETY

ALARM



POWER HEATER TAMPER

RED

BLACK

Wiring the R4222 Photo Eyes to Gate Operators

Compatible with Mighty Mule Gate Openers

1. Connect the () Terminals of the TRANSMITTER and RECEIVER to the POSITIVE terminal of

battery with wire.

2. Connect the () Terminals of the TRANSMITTER and RECEIVER to the NEGATIVE terminal of

battery with wire.

3. Connect the () Terminal of the RECEIVER to the COM/COMMON terminal of your gate

opener control board with wire.

4. Connect the () Terminal of the RECEIVER to the SAFETY terminal of your gate opener control

board with wire.

Transmitter Terminal

Receiver Terminal

Pole Mounting

1. Break out the wire hole on the

bracket then pull out the wires.

2. Remove the cover.

3. Attach the base plate on the

bracket using the Regular Ring.

DIP SETTING

NOTE:

1. DIP 1 & 2 on Transmitter & Receiver must be on the same position (same channel).

2. Dial the PIN 5 at “ON” position on Receiver. STARTUP time is about 0.06 seconds.

BEAM ALIGNMENT

1. Remove the cover, and turn ON

power.

2. Adjust the horizontal pivot, and the

vertical adjustment screw using the

built-in viewer.

3. Look through the peep hole on

either side and adjust to put the

opposite sensor in the middle of

the cross-hairs in the viewnder.

BEAM INTERRUPTION TIME ADJUSTMENT

VERIFY CORRECT OPERATION

After installation, conrm correct operation by suitable walking.

Condition Indication

Transmitter Transmitting Greed LED is ON

Receiver

Beam Clear GOOD-LEVEL Indication

Beam Blocked Alarm indication lamp is ON

Table des matières

Autres manuels Mighty Mule ouvre-porte

Mighty Mule

Mighty Mule FM350 Manuel utilisateur

Mighty Mule

Mighty Mule Mighty Mule Manuel utilisateur

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Manuel utilisateur

Mighty Mule

Mighty Mule MM360 Manuel utilisateur

Mighty Mule

Mighty Mule Silver-md single Manuel utilisateur

Mighty Mule

Mighty Mule FM502 Manuel utilisateur

Mighty Mule

Mighty Mule Automatic Gate Opener SystemFOR DUAL SWING... Manuel utilisateur

Mighty Mule

Mighty Mule Silver-HD Dual 25th annivesary series Manuel utilisateur

Mighty Mule

Mighty Mule MM272 Manuel utilisateur

Mighty Mule

Mighty Mule MMK200 Manuel utilisateur

Mighty Mule

Mighty Mule MM260 Manuel utilisateur

Mighty Mule

Mighty Mule VEHICLE SENSOR Manuel utilisateur

Mighty Mule

Mighty Mule TS571W Manuel utilisateur

Mighty Mule

Mighty Mule MM362 Manuel utilisateur

Mighty Mule

Mighty Mule MM362-D Manuel utilisateur

Mighty Mule

Mighty Mule MM562 Manuel utilisateur

Mighty Mule

Mighty Mule GTO PRO MM371W Manuel utilisateur

Mighty Mule

Mighty Mule MM660 Manuel utilisateur

Mighty Mule

Mighty Mule MM571W Manuel utilisateur

Mighty Mule

Mighty Mule MMS915 Manuel utilisateur

Mighty Mule

Mighty Mule Mighty Mule MM600 ET-PRO Manuel utilisateur

Mighty Mule

Mighty Mule TS571W Manuel utilisateur

Mighty Mule

Mighty Mule MM202 Series Manuel utilisateur

Mighty Mule

Mighty Mule UL325 SERIES Manuel utilisateur

Manuels ouvre-porte populaires d'autres marques

Elite

Elite CSW200UL Manuel utilisateur

CAME

CAME FROG-PM4 Manuel utilisateur

SOMFY

SOMFY FX230 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Manuel utilisateur

Turnstiles

Turnstiles FSW 900 Manuel utilisateur

Erreka

Erreka BUL BL33 Mode d'emploi

Erreka

Erreka VULCAN S Manuel utilisateur

Beninca

Beninca R1-2 WBV Manuel utilisateur

Erreka

Erreka VULCAN D Manuel utilisateur

Motorline professional

Motorline professional FORT Mode d’emploi

Beninca

Beninca BOB5024 Manuel utilisateur

AGA

AGA GATEMASTER 900 HD Manuel utilisateur

Chamberlain

Chamberlain MotorLift HC280ML Manuel utilisateur

SOMFY

SOMFY Dexxo RTS Pro Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur

Westfalia

Westfalia 85 27 06 Manuel utilisateur

CAME

CAME F500 Manuel utilisateur

Extel

Extel VERA Manuel utilisateur