Mighton MightyLock Manuel utilisateur

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

MightyLock

Installation Instructions

Please read the operation and ﬁtting instructions carefully before starting the installation.

MightyLock is suitable for doors from 17mm to 39mm thick.

Important: The default master code is *000000#. MightyLock requires 4 x AAA batteries to operate,

if the batteries fail, you can either use the E-Key to power the lock and gain access or use an alternative

power source via an A-B USB cable, the power output must not exceed 9v.

Do not turn the square door spindle more than 90 degrees before installing MightyLock on the door.

Important!

First install 4 x AAA batteries into the Handle Power Pack (E)

and check the handle operates using the default master code:

*000000#

Mark the height and centre of the door edge

at the height you want your door handle installed.

Parts List

Installation

1 2

A1 x MightyLock

B1 x Tubular Latch

C1 x Strike Plate

D1 x Frame Insert

E1 x Handle Power Pack

F4 x Screws

G2 x 27mm Screws

H2 x 37mm Screws

I1 x E-Key

J1 x Door Template

B C D

F G

“Make It Once...Make It Mighton...” www.mightonproducts.com

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

DOOR EDGE

CENTRE

ALIGNMENT

ø 10mm

ø 15mm

MightyLock Door Template

ø 39.5mm

ø 60.0mm

ø 80.5mm

www.mightonproducts.com

5–6

7–8

9–0

3–4

1–2

Ekey Set

“Make It Once...Make It Mighton...” www.mightonproducts.com

Installation - continued

Align the Door Template (J) with the door edge and the

template centre line with the height mark on the door. Hold

in position using masking tape.

As shown on the template, drill two 10mm holes and one

15mm hole through the door (ensure the drill is square with

the door and take care as the drill exists the opposite side).

Install the MightyLock Handles (A) using the screws (G)

provided. Ensure the handle keypad is on the correct side.

In the appropriate position on the door frame,

install the Strike Plate (C) and Frame Insert (D) using the

screws (F) provided.

On the door edge, drill a 25mm diameter hole to a depth of

88mm for the latch (ensure the drill is square with the door).

Insert the Latch (B) into the hole and draw around the edges of

the face plate. Remove the Latch (B), use a hammer and chisel

to cut out a 3mm recess to allow the face plate to sit ﬂush in

the door edge.

Install the Latch (B) into the door using the screws (F) provided.

Plug the MightyLock (A) cable into the Handle Power Pack (E).

Close the handle cover using screws (G) provided.

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

Door frame

Power Pack plug C

5–6

7–8

9–0

3–4

1–2

Ekey Set

“Make It Once...Make It Mighton...” www.mightonproducts.com

Operation

Trouble Shooting

The default master code is *000000#, this should be changed to your own code by following the steps

below. Please store your master code and the E-Key (I) in a safe place.

You can have 14 different user entry codes and each code can be up to 16 digits long.

The LED will ﬂash green for successful operations and red if the operation has failed, please check the

following table to solve any problems:

Unlock door:

*user-entry-code#

Add new user entry code:

*#master-code#1#new-user-entry-code#

Change master code:

*#old-master-code#3#new-master-code#

Delete a user entry code:

*#master-code#5#user-entry-code#

Delete all user entry codes:

*#master-code#5#000000#

Example code entry of above:

If you want to change the master code from 000000 to 132435, you would enter:

*#000000#3#132435#

5–6

7–8

9–0

3–4

1–2

Ekey Set

Operation and Status Sound LED Flashes

Adding new user entry code - Successful Long Beep 3 x Green

- Failed Alarm 3 x Red

- User code already exists 3 x Beeps 2 x Red

- Memory full, no space for new user codes 2 x Beeps + Alarm 2 x Red

Changing master code - Successful Long Beep 3 x Green

- Failed Alarm 3 x Red

Deleting a user entry code - Successful Long Beep 3 x Green

- User entry code does not exist 3 x Beeps 2 x Red

- You cannot delete the master code 3 x Beeps 2 x Red

Deleting all user entry codes - Successful Long Beep 3 x Green

- Failed Alarm 3 x Red

Unlocking door - Battery low warning n/a Green Red Green

Important: If the batteries in MightyLock fail, you can either use the E-Key to power the lock and gain

access or use an alternative power source via an A-B USB cable, the power output must not exceed 9v.

4 x new AAA batteries should then be installed.

“Make It Once...Make It Mighton...” www.mightonproducts.com

Mighton Products Ltd, Hinxton, Cambridgeshire CB10 1RG 01223 497097 [email protected]

E-Key Pairing and Operation

Resetting MightyLock

The E-Key (I) can be used as an external emergency power supply for MightyLock (A).

It can also be paired with MightyLock (A) which will allow the E-Key to unlock the door simply by

pressing the Open Button on the E-Key. You can pair up to 5 E-Key’s with each MightyLock.

If you lose or forget the master code, you will need to completely reset MightyLock (A). Doing this will

delete all user entry codes. The master code will reset to default *000000#.

Resetting MightyLock:

Open the back cover on the inside handle of MightyLock (A), press and hold the Set Button on the

Handle Power Pack (E) until MightLock beeps three times. MightyLock has now been reset to factory

settings, the master code is *000000#.

Using the E-Key as emergency power supply:

Insert the E-Key (I) into the MightyLock (A) E-Key Port. The MightyLock keypad will light up, you can

now unlock the door using your user entry or master code.

Pairing an E-Key with MightyLock:

Insert the E-Key (I) into the MightyLock (A) E-Key Port. Open the back cover on the inside handle of

MightyLock (A), press the E-Key Pairing Button on the Handle Power Pack (E) the keypad will light up

red, now press the E-Key (I) Open Button twice, the keypad will ﬂash three times. Press the E-Key (I)

Open Button and conﬁrm the door unlocks.

Unlock MightyLock using a paired E-Key:

Insert the E-Key (I) into the MightyLock (A) E-Key Port, press the E-Key (I) Open Button once, the door

will now unlock. Open the door and then remove the E-Key (I).

Unpair an E-Key with MightyLock:

Insert the E-Key (I) into the MightyLock (A) E-Key Port. Open the back cover on the inside handle of

MightyLock (A), press the E-Key Pairing Button on the Handle Power Pack (E) the keypad will light up

red, now press the E-Key (I) Open Button once, after a few seconds the keypad will ﬂash once.

Press the E-Key (I) Open Button and check the door does not unlock.

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

5–6

7–8

9–0

3–4

1–2

Ekey Set

Open Button

E-Key Pairing Button

Set Button

E-Key Port

DOOR EDGE

CENTRE

ALIGNMENT

ø 10mm

ø 15mm

MightyLock Door Template

ø 39.5mm

ø 60.0mm

ø 80.5mm

www.mightonproducts.com

Table des matières

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur