Supplemental Information: The DA-066MP Remote Chime Transmitter is activated by a relay closure on a Drive-Alert, or by pushing the button on the case. It requires 15-30
volts DC at .025 AMPS on the RED and BLACK wires. The WHITE wire when pulled to ground will activate the transmitter. DA-066MP Specications: Frequency: 315 Mhz
Crystal Controlled with ASK/OOK encoded signal, Power: .002 WATTS, Weight: 9 Ounces, Antenna: 1/8 Wave Quasi-Loop, -2 DBI Gain, Duty Cycle: 50% Encoder Duty Cycle at
1 Mhz, On Time: Normally 1 Second of Transmit Time
FCC ID: SGXMPIDA066
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes not expressly authorized by Mier Products, Inc. may void the user’s authority to operate this equipment.
IC ID: 5583ADA-066MP
Cet appareil est conforme a des reglements d’industrie Canada exempts de license standard RSS (s). Son fonctionnement est soumis aux deux conditions:
(1) Ce dispositif ne doit pas causer d’interferences nuisibles
(2) Cel appareil doit accepter toute interference recue, y compris les interferences pouvant entrainer un functionnement indesirable.
To install the DA-078 Wireless Plug-In Chime:
Turn the On/Off/Volume Knob to the desired position, and then simply plug it into a standard wall outlet within 100 feet of the DA-066MP
transmitter. Depending on the installation site, you may be able to get even greater distances.
To install the DA-080 Battery-Powered Wireless Portable Chime:
The DA-080 operates on two (2) D Batteries which will last approximately one year in a residential installation. The chime will stop
working when the batteries run too low.
To install/change batteries make sure the On/Off/Volume Knob is in the off position, remove the four black Phillips-head screws in the four
corners, and carefully open the case. Install fresh D Batteries in the battery case making sure to observe correct polarity. Replace the cover
and re-insert and tighten the four black screws making sure not to over-tighten them which might result in cracking the case. Turn the unit
back on, and turn the volume up. The chime should work up to 100 feet from the DA-066MP, and beyond, depending on the installation.
Choosing One of the Three Alert Chime Tones:
To select a different chime remove the four (4) bottom cover screws to expose the electrical board. (See Figure A)
Move the slide select switch to any of the three (3) positions. To the desired tone. Position 1 is a “Ding-Dong” chime, position 2 is a Ding-
Ding-Ding chime, and position 3 is a Dong-Ding-Dong chime. (See Figure B)
DA-078 & DA-080 Wireless Chimes
Now with New Chime Selection
Troubleshooting:
In some locations the chimes may not operate due to disruptions in the transmission path from the DA-066MP to the chimes. Common
causes of this would be appliances, furnaces, duct work, plumbing, etc. Moving the chime and/or the DA-066MP a few feet typically
solves this. If you have an older Drive-Alert system, you may have older chimes and will need to call us.
Please
contact
Mier
Products,
Inc.
with
an
y
product
or
tec
h
support
questions
at
800-473-0213
or
[email protected]Testing the chimes (see Figure C):
1) Make sure your Drive-Alert control panel is plugged in, turned on, and a DA-066MP Transmitter Pushbutton
is properly attached. Make sure your chime is either plugged-in (DA-078) or has fresh batteries (DA-080), the
On/Off/Volume Knob is turned up, and the chime is within a few feet of the DA-066MP.
2) Press the DA-066MP Transmitter Pushbutton for at least 2 seconds to make sure it activates the chime(s).
Drive-Alert Control Panel
with a DA-066MP attached
Figure A Figure B Figure C
