Miele CVA 4075 EN-CA Manuel utilisateur
Installation Instructions
CVA 4075 en-CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
The machine must be connected to
the water supply in accordance with
local and national regulations.
The water being used should have
the drinking water standards of the
respective country where the
machine is used.
– All units and systems used to deliver
the water to the coffee system must
conform with the requirements of the
respective country.
– The machine is designed to be
plumbed to a cold water connection.
– The machine can be connected
without a non-return valve.
– The on-site water line must have a
water valve to turn the water off if
needed. If not present, have a water
valve installed by a licensed
plumber.
– The water faucet must be accessible
after installation.
– Water pressure on-site:
Minimum: 14.5 psi
Maximum: 145 psi, if higher, install a
pressure reduction valve.
– Suitable 1/4" tubing or copper piping
must be supplied for plumbing.
– To ensure the best coffee quality, the
maximum length of the tubing or
copper pipe should not exceed
4 ft. 11" (1.5 m). If too much water
remains in the tubing the coffee
quality could be affected.
Connection to the water
supply
^Disconnect the machine from the
electrical supply.
^Remove the water connection cover
at the lower rear side of the coffee
machine.
^Screw the supplied brass
compression fitting, with the ¾" end,
tightly onto the water connector of the
coffee machine. The fitting includes
an opening for standard ¼" piping.
^Connect the compression fitting to
the water supply.
^Check for leaks.
Plumbing
57
Ensure that power is not supplied to
the machine while installation or
maintenance work is performed.
All electrical work should be
performed by a qualified electrician
in strict accordance with national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous.
The manufacturer cannot be held
responsible for unauthorized work.
Verify that the voltage, load and circuit
rating information found on the data
plate match the household electrical
supply before installing the coffee
system.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or contact Miele’s
Technical Service Department. See
back page for contact information.
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
Important
The coffee system comes equipped
witha6ft(1.8 m) power cord with a
NEMA 5-15P molded plug for
connection to a 120 V, 15 A, 60 Hz
power supply.
Electrical connection
58
Installation options
The coffee system is designed to be
built into cabinetry.
A combination with other Miele built in
appliances is possible. If the machine
is installed in combination with other
appliances, it should be installed with a
protective base between the appliance
and the unit (exception: installation with
a built-in plate warmer).
A special display cabinet is also
available from your dealer or Miele, as
an installation option.
Installation
59
Installation
Make sure power is not supplied to
the appliance while installation or
maintenance work is performed.
Disconnect the power supply to the
work area by unplugging the unit,
tripping the circuit breaker or
removing the fuse. The coffee
system must be installed into
cabinetry before being used.
^Unscrew the height adjustable feet
on the underside of the machine
about 1/16" (2 mm).
^Push the appliance all the way back
into the cabinet and center it. If
necessary level the unit with the four
height adjustable feet.
The feet can be turned out up to 3/8"
(10 mm).
^If your cabinet has 3/4" (19 mm) side
walls, drill four holes for the
mounting.
^Center the unit and turn the screws a
little bit in and then out again.
^Take the unit out of the niche and drill
four holes at the screw markings
(1/16" [2 mm], diameter 3/16"
[4.5 mm]).
^Connect the appliance to a cold
water supply.
^Plug the appliance into the electrical
outlet.
^Push the appliance into the niche.
^Open the door and partially tighten
the screws.
^Carefully turn the lower screws, a,to
center the machine.
^To secure the appliance in the
cabinet, tighten the upper screws, b,
by hand. Do not use an electric
screwdriver.
Installation
60
Adjusting the door hinges
The door hinges can be adjusted if the
door cannot be opened easily.
^To adjust the door sideways, a, turn
screw a.
^To adjust the door to the front or
back, b, turn screw b.
Installation
61
M.-Nr. 06 984 320 / 03
Alteration rights reserved / 2707
with convertible water connection
CVA 4075
For the most updated manual see the Miele website.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Miele Cafetière
Miele
Miele CVA 3650 Manuel utilisateur
Miele
Miele CVA 7445 Manuel utilisateur
Miele
Miele CVA 4080 Fiche technique
Miele
Miele CM5300 Manuel utilisateur
Miele
Miele CVA 5060 Manuel utilisateur
Miele
Miele CM5310BRRT Manuel utilisateur
Miele
Miele CVA7440CTS Manuel utilisateur
Miele
Miele 07 173 930 Manuel utilisateur
Miele
Miele CM6 Series Manuel
Miele
Miele DGC 6800 Manuel utilisateur
Miele
Miele CVA 2662 CVA 2662 Manuel utilisateur
Miele
Miele CVA 4062 BRWS Manuel utilisateur
Miele
Miele CM 7750 Manuel utilisateur
Miele
Miele CVA 5065 Manuel utilisateur
Miele
Miele CVA 7840 Manuel utilisateur
Miele
Miele CM 5100 Manuel utilisateur
Miele
Miele CVA 2662 Manuel utilisateur
Miele
Miele CVA 7775 Manuel utilisateur
Miele
Miele 11 674 750 Manuel utilisateur
Miele
Miele CVA 6805 Manuel utilisateur
