Middle Atlantic FlexView Series Manuel utilisateur

Thank you for purchasing a FlexView Conferencing Cart Cat 6 (FVS-800-CAT6-20F) and/or Power

(FVS-800-RET15F) Cable Retractor option. Please read these instructions thoroughly before

installing or assembling this product.

THANK YOU

FlexView Series

Conferencing Cart

Cat 6 (FVS-800-CAT6-20F) and Power (FVS-800-RET15F)

Cable Retractor Options

Instruction Sheet

Cat 6

Cable Retractor Power

Cable Retractor

100-00059 Rev A

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the

equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to

specifications.

WARNING: Middle Atlantic Products, electrical systems conform to and should be properly grounded in compliance with require-

ments of the current National Electrical Code or codes administered by local authorities. All electrical products may present a possible

shock or fire hazard if improperly installed or used. Electrical products may bear the mark of a Nationally Recognized Testing

Laboratory (NRTL) and should be installed in conformance with current local and/or the National Electrical Code.

WARNING: A warning alerts you to a situation that could result in serious personal injury or death.

AVERTISSEMENT: Un avertissement vous avertit d'une situation pouvant entraîner des blessures graves ou la mort.

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ

AVERTISSEMENT:Refus de lire, comprendre et suivre la renseignements suivants peut traduire par de graves blessures, des

dommages à l'équipement ou invalider la garantie. Il est la responsabilité de l'installateur / utilisateur de s'assurer que ce produit

est chargé conformément aux spécifications.

AVERTISSEMENT: Les produits Middle Atlantic, les systèmes électriques sont conformes et doivent être correctement mis à la

terre conformément aux exigences du Code national de l'électricité en vigueur ou aux codes administrés par les autorités locales.

Tous les produits électriques peuvent présenter un risque d'électrocution ou d'incendie s'ils sont mal installés ou utilisés. Les

produits électriques peuvent porter la marque d'un laboratoire d'essais reconnu au niveau national (NRTL) et doivent être installés

conformément au code électrique local et/ou national en vigueur.

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with dry cloth.

• Only use attachments/accessories specified by the manufacturer.

• Lire ces instructions.

• Conservez ces instructions.

• Respectez tous les avertissements.

• Suivez toutes les instructions.

• Nettoyer uniquement avec un chiffon sec.

• N'utilisez que des accessoires spécifiés par le fabricant.

DANGER HAZARDOUS VOLTAGE: The lightning flash with the arrowhead symbol, within an equilateral triangle is intended to alert the user to the

presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons.

DANGER TENSION DANGEREUSE: Le symbole de la pointe de flèche, dans un triangle équilatéral, est destiné à alerter l'utilisateur sur la

présence de tension dangereuse non isolée dans l'enceinte du produit qui peut être d'une ampleur suffisante pour constituer un risque d'électrocu-

tion.

WARNING: Exceeding the weight ratings listed can result in serious injury or damage to the equipment. It is the responsibility of the

Installer/User to ensure the components installed do not surpass the weight ratings as an unstable condition can occur which may

cause possible injury or damage.

AVERTISSEMENT: Le dépassement des poids nominaux indiqués peut entraîner des blessures graves ou des dommages à

l'équipement. C'est l'responsabilité de l'installateur/utilisateur de s'assurer que les composants installé ne dépassent pas les notes

de poids comme un instable condition peut se produire qui peut causer des blessures ou dommages.

Page 2

SUPPLIED COMPONENTS AND HARDWARE

If any pieces are missing or damaged, please report it immediately to Technical Support at

[email protected] or (866) 977-3901.

• Parts A - K are for the Cat 6 Cable Retractor (FVS-800-CAT6-20F)

• Parts L - T are for the Power Cable Retractor (FVS-800-RET15F)

Cat 6

Cable Retractor

Cat 6

Roller

Bracket

(4x)

6-32 x ⅜”

Truss Head

Screw

(4x)

6-32

Flange Nut

(2x)

10-32 x ½”

Screw

(6x)

4-40 x ½”

Pan Head Screw

INTRODUCTION

NOTE:

• Cat 6 and Power Cable Retractor options are purchased separately; however, this instruction sheet

covers the installation of both options.

• Only install your FlexView Conferencing Cart Cat 6 (FVS-800-CAT6-20F) and/or Power

(FVS-800-RET15F) Cable Retractor options after completing the steps in the FlexView Conferencing

Cart with HuddleSHOT FC instruction sheet (100-00057).

• After completing all installation procedures for your cart and any options you may have purchased,

learn to correctly operate your HuddleSHOT FC by using the additional documentation available

online at:

https://www.legrandav.com/products/technical_furniture/display_carts_and_stands/flexview_videoconferencing_cart_with_huddleshot

Some of the documents include:

• The Complete Manual for the HuddleSHOT FC (411-0037-30, this manual also includes camera

configuration details such as system administration, operation, and troubleshooting.)

• The Installation Guide for the HuddleSHOT FC (411-0037-31, a subset of the complete manual.)

• The HuddleSHOT FC Firmware Release Notes

NOTE: All documents may be accessed at

www.legrandav.com.

SUPPLIED COMPONENTS AND HARDWARE (CONTINUED)

Page 3

NOTE:

• To order more hardware, contact support at [email protected] or (866) 977-3901.

• Additional hardware is included that may not be required for your installation.

(2x)

10-32 x ½” Screw

2” Lever Lock™

Channel

Lever Lock

Adapter

Bracket

Set

(2x)

10-32 Nylon Locking Nut

Power Cable

Retractor Pin

Power Cable

Retractor Bracket

(2x)

10-32 x ⅜” Thread Cutting

Hex Head Screw

(6x)

4-40

Washer Nut

(2x)

Large Grommet

REQUIRED TOOLS

• Protective Eyewear

• Power Driver

• Hammer

• #2 Phillips Bit

• #2 Phillips Screwdriver

• 5/16” Socket or Wrench

• ¼” Socket or Wrench

• ⅜” Socket or Wrench

WARNING: Use tools with caution and

follow all necessary safety protocols.

AVERTISSEMENT: Utiliser des outils

avec prudence et suivre tous les

protocoles de sécurité nécessaires.

Power Roller

Bracket

(2x)

Small Grommet

Top, Middle, and Bottom

Audio/Video

Interface

Plates

(AVIP)

Power

Cable

Retractor

1. Open the rear door on your FlexView Conferencing Cart.

2. Temporarily remove any devices, cables, and cable

management from the inside of your cart.

3. Remove any Lever Lock™ plates and/or channels from

inside your cart. For more information, refer to "Removing

Lever Lock™ Plate and Channels" on page 15 of the

FlexView Conferencing Cart with HuddleSHOT FC

Instruction Sheet (100-00057).

4. Use a power driver or wrench and a 5/16” socket to

remove 10-32 x ⅜” hex head screws from any installed

Lever Lock™ brackets as shown (1 screw per bracket)

and set all components and hardware aside.

(FIGURE A)

5. Use a hammer and carefully clear the

knockouts on the lower-left side of the

cart as shown. (FIGURE B)

6. Use power driver, #2 Philips bit,

(4x) 6-32 x ⅜” truss head screws (A) and

(4x) flange nuts (B) to attach the

roller bracket (C) to your cart as shown.

(FIGURE C)

Page 4

PREPARING YOUR CART FOR CAT-6 RETRACTOR INSTALLATION

FIGURE A

Hex

Head

Screw

Lever Lock

Bracket

FIGURE B

FIGURE C

Clear

Knockouts

SCALE 0.500

NOTE: Hex head screw

shown in black for clarity.

ATTACHING CAT-6 RETRACTOR TO THREADED INSERTS ON BACK OF LOWER PANEL

THREADING THE CAT-6 CABLE AND INSTALLING AVIP PLATES

• Use a power driver, #2 Philips bit, and

(2x) 10-32 x ½” screws (D) to attach the Cat 6 retractor (E)

to the threaded inserts on the back of the lower panel

of your cart as shown. (FIGURE D)

Page 5

FIGURE D

Back of

Lower

Panel

FIGURE E

SCALE 0.500

1. Carefully pull at the Cat 6 cable and thread it under the roller on the roller bracket (C) and through the

knockout openings as shown. (FIGURE E)

THREADING THE CAT-6 CABLE AND INSTALLING AVIP PLATES (CONTINUED)

Page 6

SCALE 0.500

2. Slide the cable stopper down and through the knockout openings so it sits on the span of Cat 6 cable

outside of your cart. (FIGURE F)

3. Use a power driver, #2 Philips bit, (6x) 4-40 x ½” pan head screws (F), and (6x) 4-40 washer nuts (G)

to attach the AVIP pieces (H) to your cart while making sure to thread the Cat 6 cable and stopper

through the larger hole on the upper right (shaded) as shown. (FIGURE G)

5. Pull cable to desired slack and slide the stopper against the outside of the AVIP pieces (H) to secure

the length in place.

4. Use (2x) large (J) and (2x) small (K) rubber grommets to line each hole of your assembled

AVIP pieces as shown. Grommets are cut along circumference. Slip grommets around cables and line

press them into place.

6. Reinstall Lever Lock brackets, 10” Lever Lock plates, 2” channels, devices, cables, and

cable management as necessary. For more information, reverse steps 2, 3, and 4 in “Preparing Your

Cart for Cat-6 Retractor Installation” on page 4.

FIGURE F

FIGURE G

NOTE: Thread the Cat 6 cable and stopper through

the larger hole on the upper right (shaded) while

attaching the AVIP pieces (H) to your cart.

Shaded locking nuts

(G) indicates location

inside of cart.

Cable

Stopper

Page 7

1. Open the rear door on your FlexView Conferencing Cart.

2. Temporarily remove any devices, cables, and cable

management from the inside of your cart.

3. Remove any Lever Lock™ plates and/or channels from

inside your cart. For more information, refer to "Removing

Lever Lock™ Plate and Channels" on page 15 of the

FlexView Conferencing Cart with HuddleSHOT FC

Instruction Sheet (100-00057).

4. Use a power driver or wrench and a 5/16” socket to

remove 10-32 x ⅜” hex head screws from any installed

Lever Lock™ brackets as shown (1 screw per bracket)

and set all components and hardware aside.

(FIGURE H)

5. Use power driver or wrench, 5/16” socket, (2x) 10-32 x ⅜”

hex head screws (L) to attach the provided Lever Lock

adapter brackets (M) into the 4th and 5th openings (and

the 5th screw hole) from the bottom inside your cart

as shown. (FIGURE J)

6. Install Lever Lock™ channel (N) into the

adapter brackets (M).

For more information, reverse the

steps in "Removing Lever Lock™ Plate and

Channels" on page 15 of the FlexView

Conferencing Cart with HuddleSHOT FC

Instruction Sheet (100-00057).

PREPARING YOUR CART FOR POWER RETRACTOR INSTALLATION

Hex

Head

Screw

Lever Lock

Bracket

NOTE: Hex head screw

shown in black for clarity.

FIGURE J

FIGURE H

Left

Adapter

Bracket

(M)

Right

Adapter

Bracket

(M)

Fifth

Screw

Hole

NOTE:

• Attach the left and right brackets (M) into the

4th and 5th openings (and use the 5th screw

hole) from the bottom of the inside your cart.

• Brackets, 4th and 5th openings, and hole are

shown in black for clarity.

Page 8

1. Use power driver, #2 Philips bit, (2x) 10-32 x ½”

screws (P), and (2x) 10-32 nylon locking nuts

(R, not visible in figure) to attach the power

retractor bracket (S) to the 5th and 7th channel

slots on the Lever Lock channel (N) as shown.

(FIGURE K)

2. Put the top end of the retractor (U) into the

bracket (S) while aligning the holes on both

parts as shown. (FIGURE L)

3. Insert the pin (T) through the holes to secure the

retractor to the bracket.

ATTACHING POWER RETRACTOR TO LEVER LOCK CHANNEL

1. Use power driver and ⅜” socket to remove the (2x) flange nuts from the studs holding the brush in

place on your cart as shown. (FIGURE M)

2. Remove the brush from the studs.

INSTALLING THE POWER ROLLER BRACKET

FIGURE M

NOTE: The brush is attached directly

behind this location on your cart; therefore,

the expanded figure on the right shows a

flipped view of this region for clarity.

Brush

Flange

Nuts

FIGURE K

NOTE: Channel

(N) attached to

adapter brackets

inside of cart.

Align holes while

putting the top end

of retractor (U) into

bracket (S). Then insert

pin (T) through

holes on the

bracket and

retractor.

FIGURE L

Page 9

INSTALLING THE POWER ROLLER BRACKET (CONTINUED)

THREADING THE POWER CABLE

1. Carefully pull at the power cable while holding the cable stopper.

2. Thread the cable and stopper under the roller on the roller bracket (T), through the brush, and the

opening on your cart as shown. (FIGURE P)

3. Pull cable to desired slack and slide the

cable stopper against the outside of the

cart opening and brush to secure the

length in place.

4. Reinstall Lever Lock brackets,

10” Lever Lock plates, 2” channels,

devices, cables, and cable management

as necessary.

For more information, reverse steps 2,

3, and 4 in “Preparing Your Cart for

Power Retractor Installation” on page 7.

3. Place the roller bracket (T) onto the studs.

4. Use power driver, ⅜” socket, and flange nuts to reinstall the brush over the roller bracket (T) and

onto the studs as shown. (FIGURE N)

FIGURE N

Flange

Nuts

Studs

Brush T

FIGURE P

Brush

Cable

Stopper

NOTE: Thread the power

cable and stopper under

the roller on the roller

bracket (T), through the

brush, and opening.

Page 10

WARRANTY

For warranty information, refer to legrandav.com/policies/warranty_information.

Corporate Headquarters

P: (866) 977-3901 | F: (877) 894-6918 | legrandav.com | [email protected]

Middle Atlantic Canada

P: (888) 766-9770 | F: (888) 599-5009 | ca.middleatlantic.com | [email protected]

Middle Atlantic EMEA Technical Support

P: +31 495-726-003 | [email protected]

Factory Distribution

United States: New Jersey, California, and Illinois | Canada: Ontario | The Netherlands: Weert

At Legrand AV Inc. we are always listening. Your comments are welcome.

Legrand AV is an ISO 9001 and ISO 14001 Registered Company.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Middle Atlantic Dispositif de protection

Middle Atlantic

Middle Atlantic RackLink Series Manuel utilisateur

Manuels Dispositif de protection populaires d'autres marques

Sola HD

Sola HD STV100K Series Manuel utilisateur

socomec

socomec COUNTIS AMd Manuel utilisateur

Kemo Electronic

Kemo Electronic M148-24 Manuel utilisateur

SK ClickClick Manuel utilisateur

Endress+Hauser

Endress+Hauser HAW569 Manuel utilisateur

Ultrasonic

Ultrasonic SonicPRO Manuel utilisateur

nxt

nxt BIA-nXt-DPC 1-22 Manuel utilisateur

TFortis

TFortis SG-Switch Manuel utilisateur

BERNINI DESIGN

BERNINI DESIGN Be172 Manuel utilisateur

Rayleigh Instruments

Rayleigh Instruments RI-ENERGYSET-3P-ESS-50-100 Manuel utilisateur

GE Multilin 3 Series Manuel utilisateur

E.K.T.

E.K.T. ke-DP01 Manuel utilisateur

Siemens

Siemens SIPROTEC 7SD80 Manuel utilisateur

cias

cias MICRO-RAY Manuel utilisateur

Sungrow

Sungrow PVS-16MH Manuel utilisateur

Reer

Reer 32010 Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Ross

Ross Opengear SRA-8901-R Manuel utilisateur