Micsig CP2100A Manuel utilisateur

1 / 8

Micsig AC/DC Current Probes

CP2100 Series User Manual

Applies to

CP2100A/CP2100B

2 / 8

Safety Precautions

➢

The measuring circuit should be CAT II 600V or below.

➢

Do not measure bare conductor.

➢

Do not touch the conductor under test and the sensor head while

measuring.

➢

Do not operate in wet/damp conditions.

➢

Do not touch the instrument or the object under test with wet hands.

➢

Please use this product within the scope permitted by the terminal.

➢

Please use this product as required.

➢

Please ground the product through the USB power cable.

3 / 8

1. Introduction

The CP2100 series is a current probe that can measure both DC and AC. It is

a split-type design that is small and beautiful. It uses a standard BNC

interface for oscilloscopes or a multi-connector for adapters. The maximum

current that can be measured is 100Apk

(70Arms); it is divided into 2 models, CP2100A measurable bandwidth range

is DC~800KHz, CP2100B measurable bandwidth range is DC~2.5MHz,The

CP2100 series current probe has two optional ranges: 10A and 100A . With

automatic and manual zero adjustment, USB power supply, no additional

power supply, making measurement more convenient. Often used in motor

drive, power frequency, inverter, power supply, avionics and other fields.

2. Appearance

4 / 8

2. Specifications

Parameter

CP2100A

CP2100B

Bandwidth

DC~800KHz

DC~2.5MHz

Rise time

≤583ns

≤175ns

Ranges

10A/100A

Output sensitivity

0.1V/A (10A)

0.01V/A (100A)

DC accuarcy(typical)

3%±50mA (10A)

4%±50mA (100A, 500mA~40Apk)

15% (100A, 40Apk~100Apk)

Signal delay

<150ns (10A)

<200ns (100A)

DC signal linearity (typical)

DC signal linearity, typical on page 6

Measuring range

50mA~10Apk (10A)

1A~100Apk (100A)

Maximum measurable

current

100Apk, 70.7Arms (DC+ACpk)

200Apk-pk, 70.7Arms (AC)

Maximum working voltage

CAT III 300V CAT II 600V

Maximum float voltage

CAT III 300V CAT II 600V

Maximum conductor

diameter

13mm

Overload indication

The buzzer beeping, the button light flashing

Power supply

DC 5V

Probe head size

11*6.1*2.5cm

Control box size

10.8*5.6*2.6cm

Length

228cm

Weight

290g

Single package weight

1000g

Single package size

29.5*23.6*5.7cm

Operating Temperature

0°C ~50°C

Storage Temperature

-20°C ~80°C

Operating Humidity

5%~95% (0°C ~40°C , No condensation)

5%~65% (40°C ~50°C , No condensation)

Operating Altitude

≤3000m

Storage Altitude

≤12000m

5 / 8

Maximum current versus frequency

Amplitude-frequency characteristic curve -CP2100A

6 / 8

Amplitude-frequency characteristic curve -CP2100B

DC signal linearity

7 / 8

3. Instructions：

1.ConnecttheBNCofthecurrentprobetotheoscilloscope(orotherinstrument)

andconnecttheUSBcabletopowerthecurrent probe.

2.According to the current, select the appropriate range on the probe, the

corresponding button light turns green.

3.Adjust the oscilloscope settings: input impedance 1MΩ; Select current or

set display unit as A; Set the probe attenuation multiplier of the corresponding

channel. If the probe is 100A(0.01V/A), the oscilloscope should be 100X, if

the probe is 10A(0.1V/A), oscilloscope is 10X.

4.Press the auto zero button to realize the auto zero adjustment of the

probe. After the zero adjustment is successful, the buzzer will beep for

once. Otherwise, the “beep” sound will be 3, indicating that the zero

adjustment fails; The external magnetic field may have a slight influence

on the DC zero of the probe. After the zero adjustment is completed,

please do not move it in a large range.

5. Open the clamp of the current probe to clamp the conductor under test

according to the direction indicated by the clamp head. Note: If the

measured current flow direction is opposite to the direction indicated by

the clamp head, the output is negative.

6. Adjust the oscilloscope to get the best waveform.

Note: When the current exceeds the range, the buzzer will sound for a long

time and the button light will flash.

5. Maintenance

During the product warranty period and under normal use, the company

will be responsible for free maintenance due to the failure of the product

itself due to quality problems.

Please keep the product as dry, clean and tidy. If there is dirt, use a soft

cloth or sponge with alcohol to remove dirt. Do not use water.

In order to ensure the performance of the product, it is recommended to

conduct an inspection or calibration once a year.

8 / 8

Version

Modify content

release time

1.0

First release

2019.05

The information provided in this document is provided on an "as is" basis

and is subject to change without notice in future editions. Further, Micsig

disclaims all warranties, either express or implied, with respect to this

manual and any information contained herein, including but not limited to

the implied warranties of merchantability and fitness for a particular

purpose, to the fullest extent permitted by applicable law. Micsig is not

responsible for errors or accidental or consequential damages resulting

from the furnishing, use, or use of this document or any information

contained herein. In the event that a separate written agreement between

Micsig and the user contains a warranty term covering the contents of this

document, but the warranty terms conflict with those terms, the warranty

terms in the separate agreement shall prevail.

Shenzhen Micsig Instruments Co.,Ltd.

Tel: +86-755-88600880 E-mail: sales@micsig.com

Web: www.micsig.com

Add:305 Block A, CLOU Building, Baoshen RD, North Area,

Nanshan Science&Technology Park, Shenzhen, Guangdong,

China, 518000

Autres manuels pour CP2100A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Micsig Équipement de test

Micsig

Micsig DP10007 Manuel utilisateur

Micsig

Micsig ATO1000 Series Manuel utilisateur

Micsig

Micsig Smart Series Manuel utilisateur

Micsig

Micsig RCP Series Manuel utilisateur

Micsig

Micsig MS300 Series Manuel utilisateur

Micsig

Micsig SigOFIT MOIP01P SigOFIT MOIP01P Manuel utilisateur

Micsig

Micsig tbook mini Series Manuel utilisateur

Micsig

Micsig MS200 Series Manuel utilisateur

Micsig

Micsig DP5013 Manuel utilisateur

Micsig

Micsig DP750-100 Manuel utilisateur

Micsig

Micsig MDP Series Manuel utilisateur

Micsig

Micsig VATO Series Manuel utilisateur

Micsig

Micsig ATO Series Manuel utilisateur

Micsig

Micsig SATO1000 Series Manuel utilisateur

Micsig

Micsig DP750 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur